Question about 1999 Lincoln Navigator

1 Answer

Can the front two wheels be disconnected from being 4 wheel drive on a 1999 navagator?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 144 Answers

Hi, frist of all is it all time four wheel drive,if it is all time the answer is no. but if you have to put it in four wheel drive , just pull the axels out of front . thanks dodge tec

Posted on Jan 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honda passport 1999 stuck in 4 wheel drive


Possible bad front diff actuator.

Jan 14, 2015 | 1999 Honda Passport

1 Answer

My 1999 Rav 4 is normally a front wheel drive but can switch to 4 wheel drive. Do I need alignment in all 4 wheels or just the front?


Most alignment shops these days use a 4 wheel system,so they see all 4 wheels anyway,I would try to tell the shop if the rear is ok ,just do the front.
That 2 wheel 4 wheel price is a moneymaker
So hard to find an honest shop.

Apr 10, 2012 | 1999 Toyota RAV4

1 Answer

My 1999 Blazer 4X4 will not go into 4 wheel drive.


The cv shafts will turn in 2wd but the front driveshaft should not. Can you jack up all 4 wheels to test this?

Jul 04, 2009 | 1999 Chevrolet Blazer

2 Answers

1999 GMC sonoma starte installation


2.2L Engine remove protective shields as needed then remove front exhaust pipe. Remove the brace from the engine to the clutch housing, then disconnect starter wiring. 4.3L Engine 2 wheel drive just remove the right front tire and you will have access to the wiring. 4.3L Engine 4 wheel drive you must remove the differential carrier shield if equipped then remove the starter bolts and rotate the starter to get access to the wiring. Good Luck.

Jun 15, 2009 | 1999 GMC Sonoma

1 Answer

I have a Disco II and the wheel hub bearing went and i'm tryign to change it but i cant seem to get the hub off, can any one help with a step to step guide or something, thanks.


RAVE says the following:
1) Release ABS Sensor harness grommet from inner wing valance and disconnect multi plug.
2) Raise front of vehicle.
3) Remove road wheel.
4) Pull ABS Sensor harness through aperture into wheel arch.
5) Release harness from brackets on inner wing valance, suspension turret and front hub.
6) Release stake from drive shaft nut
7) Remove drive shaft nut with assistance & discard.
8) Remove front brake disk (Remove calliper, pad holder, screw and tap to remove)
9) Remove 4 bolts securing wheel hub to steering knuckle.
10) Release wheel hub from steering knuckle then remove wheel hub and drive shaft assembly from axle. DO NOT REMOVE ABS SENSOR FROM HUB. HUB AND SENSOR ARE SUPPLIED AS AN ASSEMBLY.
11) Position the wheel hub and drive shaft on a press, place supports beneath the wheel studs and press the drive shaft from the wheel hub.
12) Remove drive shaft oil seal from axle casing.

Refit is mostly the reverse, you need to take care to lubricate things in the right places and put loctite on the drive shaft and locate the loom and torque everything right.

Mar 24, 2009 | 1999 Land Rover Discovery

1 Answer

1999 Silverado, 5.3 engine, 4 wheel drive, How to tow.


i have towed this type of truck with disconnecting both drive shafts and putting front wheels onto a tow dolly so you don't blow out transfer case or do damage to front axle

Nov 30, 2008 | 1999 Chevrolet Silverado 1500

1 Answer

1999 Isuzu Rodeo LS, 4 wheel drive


it is probably a brake adjustment problem

Oct 18, 2008 | 1999 Isuzu Rodeo

1 Answer

Warning light for 4-wheel drive


I had this problem on my 1995 Montero. The 4-wheel-drive indicator lights wouldn't stop blinking when I switched from 4-wheel drive to 2-wheel drive. It turns out that I had a slow leak in one of the front tires. After I fixed the leak and made sure the pressure was the same in both front tires, the problem went away. 
This made sense to me because if one tire is much lower in pressure, it's closer to the ground, i.e. has a smaller radius, and therefore rotates more quickly. The manual says to drive in a straight line when disengaging 4-wheel drive but with the lower tire pressure on one side it was the equivalent of driving in a circle. 
You could try checking your tire pressures and see if that makes a difference. Hope this helps. 

Sep 06, 2008 | 1999 Mitsubishi Montero Sport

1 Answer

Front wheel will not engage for 4 wheel drive


very possible. Put your jeep on 4 jackstands and put in 4 wheel drive. if the front drive shaft turns pull the vacuum disconnect and check the shift fork. They usually break before the shift actuator.

Jun 28, 2008 | 1992 Jeep Wrangler

Not finding what you are looking for?
1999 Lincoln Navigator Logo

Related Topics:

236 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...