Question about 1991 Chevrolet S-10 Blazer

1 Answer

HOW TO REMOVE STEERING WHEEL ON A 1991 S10 PU 2 WHEEL DRIVE TO GET TO COLUMN MOUNTED WIPER SWITCH

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

The wiper switch just pulls out with a little force you only need to pull the steering wheel if you are removing the turn signal switch.

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replace wiper switch


wiper and washer switch in steering column you more likely need to remove steering wheel to get to switch two mountings screws on the right side.disable airbags before replacing switch. first turn off radio ignition switch off then disconnect negative battery cable. wait 20 minutes before removing steering wheel and remove steering column.

Sep 12, 2013 | Cars & Trucks

1 Answer

Turn indicator/wiper switch assembly replacement instructions please?


steps required to remove and replace indicator switch assembly.
1.disconnect the battery earth lead.
2.from the rear of the steering wheel remove the screws retaining the horn pad..
3.lift the horn assembly away from the steering wheel far enough to remove wiring.
4.Once that is done then move to the next step.
5.Remove the locknut and steering wheel nut .
6.then mark the end of the steering shaft and the steering wheel to correctly relocate and install in same position.
7.then with the correct tool remove the steering wheel from shaft.
8.then once the steering wheel is removed you can then move on to removing the lower steering column cover screw and then remove cover.
9.disconnect the wiring from the multi point connector under instrument panel.
10.release and free wiring harness.
11.unscrew and remove the hazard switch knob.
12.remove the dipper-wiper switch securing screw and manoeurve the switch upwards.guiding the wiring through the column.
13.you will actual find there are 3 phillip head screws securing the switch to lever switch to the combination switch.

14.when putting this assembly back to together just follow these steps in reverse..
hope you find this helps you

Aug 03, 2012 | Holden VK Cars & Trucks

1 Answer

The windshield wiper switch on my 2001 lumina needs to be replaced and I am thinking of doing it myself. How hard is it to do this? Is it true that I would need to take the steering wheel off?


No , the steering wheel doesn't need to be pulled off . The wiper switch just pulls out of the steering column .

Verify that the lever (2) is in the center of the OFF position.
Disconnect the electrical connection (3) behind the lever (2).
Remove the switch lever (2) by pulling straightly outward on the lever .

Nov 25, 2010 | 2001 Chevrolet Lumina

2 Answers

1994 ford tauris windshirld wiper switch


Remove plastic cover around column, three or four screw's, then remove three small bolt's on wiper switch same switch as turn signal there together, disconnect harness and remove and replace with new switch, there's no service to switch if bad it just get replace.Hope this was very helpful

Jan 21, 2010 | 1994 Ford Taurus

1 Answer

Some times wipers would come on with out turning on the wiper switch and now will not turn off at all


Sounds like a bad wiper switch assembly.

Removal & Installataion
  1. Disconnect the negative battery cable. Remove the steering wheel.
  2. On vehicles equipped with tilt wheel, remove the tilt lever.
  3. On vehicles equipped with tilt wheel, remove the steering column collar by pressing on the collar from the top and bottom while removing the collar.
537bccf.gif
To remove the tilt column control lever, simply rotate it counterclockwise until removed

4ab784d.gif Exploded view of the combination switch mounting and column related wire harness connectors


  1. Remove the instrument panel trim cover retaining screws. Remove the trim cover.
  2. Remove the 2 screws from the bottom of the steering column shroud. Remove the bottom half of the shroud by pulling the shroud down and toward the rear of the vehicle.
  3. If the vehicle is equipped with automatic transmission, move the shift lever as required to aid in removal of the shroud. Lift the top half of the shroud from the column.
  4. On 1991 automatic transmission equipped models, disconnect the selector indicator actuation cable by removing the screw from the column casting and the plastic plug at the end of the cable.
  5. Remove the 2 self tapping screws that retain the combination switch to the steering column casting. Disengage the switch from the casting.
  6. Disconnect the 3 electrical connectors, using caution not to damage the locking tabs. Be sure not to damage the PRNDL cable.
  7. Installation is the reverse of the removal procedure. Torque the combination switch retaining screws to 18-27 inch lbs. (2-3 Nm).

Oct 26, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Is it difficult to replace the combination light switch


It all depends on the tools you have and if you have patience....this is the task for removing and replacing the switch:

Removal & Installataion
CAUTION These models covered are equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS and refer to the precautions in the Chassis Electrical Section.


  1. Make sure the steering wheel is in the center position (wheels in the straight ahead position)
  2. Remove the key from the ignition.
  3. Disconnect the negative battery cable first, then the positive cable.
  4. Wait 10-20 minutes for the back-up power to discharge. Do NOT proceed until the back-up power is discharged from the SRS system!
  5. Remove the driver’s side air bag module and steering wheel, as outlined under the Steering Wheel Removal & Installation procedure in this section.
  6. Remove the steering column nacelle, as follows:
    • Open the fascia lower access panel.
    • Remove 3 screws securing steering column nacelle halves together.
    • Release clips securing nacelle together and remove from steering column.
91d9def.gif
Exploded view of the steering column nacelle (cover) mounting

Remove the rotary coupler, as follows:
  • Release rotary coupler connector from bracket and disconnect from harness.
  • Disconnect rotary coupler connector from harness.
  • Remove rotary coupler.
36a7806.gif
View of the rotary coupler

  1. Release passive coil from steering column lock and lower the coil without disconnecting the harness.
  2. Release front wiper delay connector from column switch mounting bracket and disconnect from harness.
  3. Disconnect harness connector from wiper switch.
  4. Remove 2 screws securing switch, carefully raise edge of switch bracket to clear location peg and remove switch.
c23a31c.gif
Release front wiper delay connector (3) from column switch mounting bracket and disconnect from harness. Disconnect the wiper switch connector (4), then remove the switch mounting screws (5)

To install:
  1. Install the new switch to bracket and secure with screws.
  2. Connect harness connector to switch.
  3. Connect front wiper delay connector and Install the connector to switch bracket.
  4. Install the passive coil to column lock.
  5. Install the rotary coupler, as follows:
    • Install the rotary coupler to steering column and connect connector to harness.
    • Connect rotary coupler connector to harness and secure to bracket.
  6. Install the steering column nacelle, as follows:
    • Position the nacelle to steering column and secure with clips and screws.
    • Close fascia lower access panel.
  7. Install the steering wheel and driver’s air bag module, as outlined in this section.
  8. Connect the positive, then the negative battery cables.

Oct 13, 2009 | 2001 Land Rover Discovery Series II

1 Answer

How do you replace the wiper switch on the column of paseo


you need to remove the steering wheel once the wheel is off you should be able to remove the switch

Sep 25, 2009 | 1994 Toyota Paseo

3 Answers

I have a 87 blazer s10... the turnswitch /wiper/highbeam switch is broken and is shorting out my brakelights ..i cant seem to get to it.. took the steering weel off but ..?


Unfortunately there are some special tools required you will need to get to the turn-signal switch. Below is the procedure for replacing the turn-signal switch. Generally you can rent the puller from a local auto parts jobber or you can purchase one.
Good luck, let me know how it goes.
Regards,

Many vehicles use a turn signal switch that is separate from the multifunction switch. The steering wheel will have to be removed to gain access to the turn signal switch on these vehicles. The following procedure is a common method of turn signal switch replacement:
  • Place the fender covers on the fenders.
  • Disconnect the negative battery cable.
  • Remove the steering column trim.
  • Remove the horn pad from the steering wheel.
f_aee_cc14.28.jpg Steering wheel attachment. Courtesy of General Motors Corporation, Service Technology Group.
  • Remove the steering wheel and horn collar.
  • Use a suitable puller to remove the steering wheel.
  • With a suitable compressor, compress the preload spring to the lock plate. Compress the spring only enough to remove the snap ring.
f_aee_cc14.29.jpg To remove the snap ring, use the compressing tool to relieve the pressure against the snap ring. Courtesy of General Motors Corporation, Service Technology Group.
  • Use a pick and a small flat blade screwdriver to remove the snap ring.
  • Remove the lock plate, horn contact carrier, and spring.
  • Remove the bolts at the upper steering column support and the upper mounting bracket from the column.
  • Disconnect the turn signal wiring connector.
  • Wrap tape around the wire and connector.
  • Remove the hazard warning knob from the column.
  • Remove the switch retaining screws and remove the switch.
f_aee_cc14.30.jpg Remove the turn signal switch from the column. Courtesy of Chrysler Corporation.
  • Replace the switch and reverse these procedures for reinstallation.

Sep 19, 2009 | 1987 Chevrolet Blazer

1 Answer

How do i remove ignition switch on a 1991 f150 ?


HI, follow the steps below to help with this issue.



Step 1

Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing or unclipping them.

Step 2

Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

Step 3

Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

Step 4

Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

Step 5

Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

Step 6

Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.



Jul 11, 2009 | 1991 Ford F150

1 Answer

Need to relace the wiper/cruise control lever s10


take the cover off the wheel remove the center nut and you will have to get a steering wheel puller and crank that down on the center screw until the wheel comes off and then once you have the switch in just get the steering wheel in place and have it where you can catch a few threads and tighten it back down

Apr 12, 2009 | 1987 Chevrolet S-10 Pickup

Not finding what you are looking for?
1991 Chevrolet S-10 Blazer Logo

482 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...