Question about Ford Escort

Open Question

Where is the water pump located on a ford split port induction 2000 also the thermastat

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 62 Answers

SOURCE: Low pressure port 2000 ford explorer

im assuming your talking about the a/c low pressure port? it should be on the receiver/drier(steel can with 2 lines hooked to it) or in the lines connecting to it

Posted on May 15, 2009

seans46
  • 161 Answers

SOURCE: location low pressure port a/c 2000 ford ranger 3.0

I am not sure I thought some of them were on the back of the compressor which makes it hard to see . but one thing for sure follow the low press line towards the evap and you will find it

Posted on Jun 09, 2009

  • 1 Answer

SOURCE: NEED THE FAN BELT DIAGRAM OF A FORD FOCUS 2000 2.0

replacement belt diagram 2000 ford focuszx3

Posted on Jul 26, 2009

techbuster
  • 5081 Answers

SOURCE: How to change a 2000 ford explorer bypass hose?

You have to remove the tensioner assembly, not just the tensioner pulley, but the whole assembly, in order to access the plastic bypass hose.
Be very careful, as these pipes get old, the plastic becomes brittle, and possibly the flange end will break off and remain in the block when you remove the pipe, check the block opening carefully to remove all of the remaining flange.
Also, be very careful when removing the lover pipe nipple into the engine block, if you try to pry the tensioner assembly off the block, you will probably snap off the machined nipple that locates into the block, Ask me how I know!!! Good Luck, it can be done but you need to move carefully and deliberately. (by the way, a rebuilt tensioner assembly costs about $80 US, the pipe is about $6. New tensioner assembly comes with the pipe)

Posted on Sep 21, 2009

bsdracing
  • 57 Answers

SOURCE: where is the water pump located on a 2000 ford

it is on the passenger side of car/ front of engine pretty hard to get too it is probably easier to see from under front of car it will be center of the way up the front of engine

Posted on Apr 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need a vacuum hose diagram for a ford mercury tracer ls. the motor is a 4 cylinder split port induction 2000. i cant seem to find one.


Basic vacuum routing is under hood above your head when you lift hood, or sometimes near center top of radiator support in front of you. don

Jan 12, 2017 | Mercury Tracer Cars & Trucks

2 Answers

Where is the thermostat located on a 2000 nissan xterra? Is there a diagram anywhere?


Hi, the thermostat is located in the housing just above the water pump. Follow the top hose on the radiator. There is a metal tubing in the middle of that top hose that leads to the thermostat housing. The housing has 3 screws that attaches it to the engine.

Jun 11, 2011 | 2000 Nissan Xterra

1 Answer

How can I tell which 2.0L engine is in my 1998 Ford Escort?


If the spark plug wires go in the front of the engine it is an 8 valve SPI (split port induction) motor.

Apr 10, 2010 | 1998 Ford Escort

1 Answer

My 1995 ford winstar gl 3.8 split port induction.....i changed the oil pump and am still not getting any oil pressure...I pulled it off again and checkt 2 c if the oil pump shaft is turning and it is...


did you prime the oil pump, if not you locked the oil pump up. when installing a new oil pump you must prime it with new oil. if your cam isn't turning it sounds like your cam broke or your timing chain broke.

Jan 25, 2010 | Ford Windstar Cars & Trucks

1 Answer

Radiator is overheating chaned thermastat still


water pump is the problem,you will find the the water pump impellor has broken or come loose from the shaft,you going to have to replace the water pump

Oct 19, 2009 | 2000 Volkswagen Jetta TDI

1 Answer

How to change a 2000 ford explorer bypass hose?


You have to remove the tensioner assembly, not just the tensioner pulley, but the whole assembly, in order to access the plastic bypass hose.
Be very careful, as these pipes get old, the plastic becomes brittle, and possibly the flange end will break off and remain in the block when you remove the pipe, check the block opening carefully to remove all of the remaining flange.
Also, be very careful when removing the lover pipe nipple into the engine block, if you try to pry the tensioner assembly off the block, you will probably snap off the machined nipple that locates into the block, Ask me how I know!!! Good Luck, it can be done but you need to move carefully and deliberately. (by the way, a rebuilt tensioner assembly costs about $80 US, the pipe is about $6. New tensioner assembly comes with the pipe)

Sep 21, 2009 | 2000 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...