Question about 2002 Chevrolet Silverado 2500HD
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Fuel Rail Pressure Low During Power Enrichment
The engine control module (ECM) uses the fuel rail pressure (FRP) sensor to determine fuel pressure to the fuel injectors. This is then compared to the calculated target fuel pressure as determined by the ECM. The ECM adjusts the FRP by modulating the duty cycle of the control driver of the fuel pressure regulator. Injector pulse duration is determined by the measured rail pressure and the target injection fuel into each cylinder. If a sensor circuit malfunction is detected, or the commanded fuel injection pump flow is not within the proper range for a given engine load and speed, DTCs will be set.
DTC U1000 and U1255 Circuit Description Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module records the identification number of the module which sent the message for State of Health monitoring. A critical operating parameter is one which, when not received, requires that the module use a default value for that parameter. When a module does not associate an identification number with at least one critical parameter within about five seconds of beginning serial data communication, DTC U1000 or U1255 is set. When more than one critical parameter does not have an identification number associated with it, the DTC will only be reported once. The class 2 serial data line on this vehicle is a ring/star configuration. The following modules communicate on the class 2 serial data line:
• The body control module (BCM) • The digital radio reciever • The driver door module (DDM) • The electronic brake control module (EBCM) • The front passenger door module (FPDM) • The HVAC control module • The inflatable restraint sensing and diagnostic module (SDM) • The instrument panel cluster (IPC) • The memory seat module (MSM) • The powertrain control module (PCM) • The radio • The radio amplifier • The rear seat audio (RSA) controller • The rear seat entertainment (RSE) assembly w/U42 • The rear wheel steering control module • The remote playback device-CD player w/U1S • The transfer case shift control module • The transmission control module (TCM) w/Allison transmission • The theft deterrent control module • The vehicle communication interface module (VCIM) w/UE1
Posted on Dec 09, 2008
The requirement is 10 QTS. I use 10 and check it cause some times they hold 11 QTS. I hope this helps. If you have more questions reguarding this or other conserns please ask me. Please remember high ratings are very important to me.
Posted on Aug 28, 2009
Testimonial: "Thanks very much for that Regards Bryan McRae New Zealand"
the power steering lines are very short hoses approximately 8 inches long that go from the power steering pump down to the steering box, which is located on the frame, just below the pump. The brake lines run from the master cylinder(where you fill it with fluid on the drivers side firewall) down to the frame, and then follow the frame both directions; both to the front end and the rear end, along the drivers side frame rail, just on the inside of it. The fuel line runs along the same path to the rear.
Posted on Oct 03, 2009
Clicking, especially while turning usually more so points to a problem with the CV joint, or axel, the easiest way to test a wheel baring is to jack up that side of the truck until the tire is off the ground, leave the lug nuts on and try to wobble the tire in all directions, if everything seems solid it is not likely the bearing casuse the sound, another note when a bearing starts to go bad, it usually hums opposed to clicks. Im sorry i dont have a diagram, but this proceedure should get you on the right track in diagnosing the issure, good luck!!
Posted on Mar 21, 2010
The air filter is located under the hood, passenger side, up by the windshield. it has a small retangular cover about 3 X 10 that pulls off
Posted on Jun 13, 2010
Tips for a great answer:
Aug 16, 2013 | 2005 Chevrolet Silverado 3500
Oct 09, 2011 | 2002 Chevrolet Silverado 2500HD
Jun 28, 2011 | 2002 Chevrolet Silverado 2500HD
Jun 13, 2010 | 2002 Chevrolet Silverado 2500HD
Jan 02, 2010 | 2002 Chevrolet Silverado
Sep 30, 2009 | 2007 Chevrolet Silverado 2500HD
Sep 12, 2009 | 2002 Chevrolet Silverado 2500HD
Jun 21, 2009 | 2003 Chevrolet Silverado 2500HD
Aug 04, 2014 | 2002 Chevrolet Silverado 2500HD
382 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: