Question about 1999 Chevrolet Lumina

2 Answers

1999 lumina chev brake light stop no work - 1999 Chevrolet Lumina

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Check the turn signal switch. This is a bad problem in luminas. See if brake lights work after jiggleing switch

Posted on Nov 03, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 870 Answers

Check the brake light fuse if its ok then check the bulbs if they are ok then check the brake light switch. Good luck

Posted on Jan 03, 2011

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1201 Answers

SOURCE: how can I add freon to 1999 chev lumina

Get an a/c charging kit, it comes with a can of freon usually with a blue hose, and a small guage on it. The type is R134a.
Under the hood look for the a/c pipes, one has a red cap which is the high pressure, and the other has a blue cap,( that can be anywhere), that's the you need. Unscrew the cap, screw the blue hose on to the pipe, DO NOT TURN CAN UPSIDE DOWN. Start engine, turn on a/c full blast, open valve on can. Shake once in a while. When can is empty disconnect. If no other problems with system, there should be cool air coming out.

Posted on Jun 29, 2009

jturcotte
  • 7795 Answers

SOURCE: 1999 Chev Lumina, brake lights

Hi, this symptom is caused by a failed turn signal switch. I have pasted procedures below for replacing the switch. You will need a steering wheel puller to access the switch. Other tools needed are mostly screwdrivers or small nut drivers, except for the steering wheel nut, which is a larger one--about 15 or 17 mm.

REMOVAL & INSTALLATION

  1. Center the front wheels and lock the steering column. Remove the key from the ignition.
  2. Disable the SIR (air bag) system by removing the SIR fuse and disconnecting the negative battery cable.
  3. Remove the air bag module from the steering wheel using the following procedure:
NOTE The air bag can be retained to the steering wheel with several different types of fasteners, depending on Model Year and vehicle equipment. A small mirror may be helpful to examine the back of the steering wheel to determine how the air bag is retained on your vehicle. It could be by Torx®screws which are unscrewed using the proper bit (usually a #30 driver bit). An alternate method of attachment is by small leaf-type springs which are unclipped with a small flat-blade prytool.
  1. On the back side of the steering wheel, locate and remove the air bag fasteners.
  2. Gently pull on the air bag module to free it from the steering wheel.
  3. Detach the electrical connections from the steering wheel to the air bag module.
  4. Place the air bag in a safe place, with the trim pad facing upwards.

  1. Scribe an alignment mark on the steering wheel hub in line with the existing mark on the steering shaft.
  2. Loosen, but do not remove the steering wheel shaft nut, positioning it flush with the end of the steering column shaft. This is protect the steering column shaft threads from the foot of the steering wheel puller center screw.
  3. Assemble a suitable steering wheel puller (GM recommends their J 1859-A puller with J 36541 special legs) to the steering wheel and pull the wheel loose from the shaft.
  4. Remove the steering wheel shaft nut and the remove the steering wheel. Detach the electrical connectors.

jturcotte_2031.gif

Fig. If leaf-type springs are used to retain the air bag, release the spring clip retainers and separate the air bag module from the steering wheel


jturcotte_2032.gif

Fig. Carefully pull the air bag module away from the steering wheel, then detach the electrical connector

jturcotte_2033.gif

Fig. Exploded view of the air bag module and electrical connections-Buick shown, others similar


jturcotte_2035.gif

Fig. Typical steering wheel and the recommended puller with special legs to fit steering wheels designed for air bags





  1. Make sure the multifunction lever is in the OFF position.


jturcotte_2036.gif

Fig. Typical multifunction switch removal

  1. Remove the screws from the lower steering column cover. It may be helpful to tilt the column down and slide the cover back to disengage the plastic locking tabs. Work carefully. The plastic column covers are easily damaged.
  2. Remove the screws from the upper steering column cover and lift off the cover.
  3. Disconnect the wire harness strap.
  4. It is likely that wire ties restrain the multifunction switch harness. Cut off the plastic wire ties.
  5. Detach the steering column harness connector from the vehicle wire harness.
  6. Remove the two tapping screws and separate the turn signal and multifunction switch assembly from the steering column.
  7. Installation is the reverse of the removal process. Use new plastic wire ties to secure the harness as before.
  8. Test all multifunction switch operations.


  1. Route the SIR connector through the steering wheel.
  2. Align the scribe mark on the steering wheel made at removal with the existing mark on the steering column shaft. Make sure the steering wheel is seated.
  3. Install the steering wheel shaft nut and tighten to 33 ft. lbs. (45 Nm).
  4. Install the air bag module using the following procedure:
    1. Attach the electrical connections to the air bag module.
    2. If equipped with leaf-spring type clips, line up the air bag module retainers with the openings in the steering wheel. Gently press the air bag module into place until it 'snaps' into place.
    3. If equipped with screws to retain the air bag, install the screws using care to line up the screw openings.

  5. Enable the SIR system by replacing the fuseand reinstally the negative battery cable.
  6. Check the operation of the horn and steering wheel. Check the operation of the steering wheel switches, as equipped.

Posted on Aug 07, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Left turn signal doesnt work and my brakelights


  1. Check the fuse make sure it is not busted and also use a designated amp only.
  2. Check the bulb and the wires also.

Mar 28, 2010 | 1997 Chevrolet Lumina

1 Answer

I have a 99 lumina i have no brake lights and


check for power to brake light switch and comming out, sounds like bad brake light switch

Feb 04, 2010 | 1999 Chevrolet Lumina

1 Answer

Brake lights will not work turn signal works fuse is ok


if no brake lights are working,not even the high stop light in the rear window,And you have checked the brake lights fuse with a test light,it will be time to check the stop light switch located on brake pedal under dash.

Nov 26, 2009 | 1999 Chevrolet Lumina

1 Answer

I have break light in the back window, but not on the taillights


95 Chev Luminas have a problem with the combination signal light, light dimmer switch. Found out by holding brake and wiggling switch.

Sep 23, 2009 | 1995 Chevrolet Lumina

1 Answer

1999 Chev. Cavalier no brake lights. Bulbs and fuses O.K.


check the brake light switck .its under the dash above the brake pedle

Jul 17, 2009 | 1999 Chevrolet Cavalier

1 Answer

Brake lights do not turn on


try brake switch under the brake pedal and check all fuses.

Apr 11, 2009 | 1999 Chevrolet Lumina

1 Answer

Dash and tail lights went out


look at fuse for your cigar lighter

Dec 26, 2008 | 1995 Chevrolet Lumina

Not finding what you are looking for?
1999 Chevrolet Lumina Logo

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...