Question about 1999 Chevrolet Blazer

1 Answer

1999 chevy blazer brake gos down to the floor i bleed the bleed the brake system but there is no pressure at rear

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

You need to bleed the fronts to reset the check valve .

Posted on Jan 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced brake line on 1999 blazer bleed brakes still goes to floor


you need to start at the farthest rear and bleed it make sure someone is pumping and holding brake while doing this .. then move to next farthest .. then pass front and then driver side until the whole system has gotten air out.. keep your brake master cylinder full all the time..

Apr 23, 2014 | 2000 Chevrolet Blazer

1 Answer

Replaced brake line on 1999 blazer bleed brakes still goes to floor


keep bleeding but u need to bleed all brakes---start with furthest passenger side rear --drivers side rear --passenger front than finish with drivers side front it will seem like your bleeding forever but you will have a lot of air when replacing a line

Apr 23, 2014 | Volkswagen Passat Cars & Trucks

2 Answers

Bled brakes on my 1999 chevy blazer still goes to floor


this is an indication that there is still air in the system and the bleeding process was inefficient. Bleed the lines at the master cylinder first by loosening off the lines and holding the pedal down until the lines are retightened. Then starting at the longest line first bleed the system finishing at the shortest line . Keep the fluid level in the reservoir topped up at all times.

Apr 21, 2014 | 1999 Chevrolet Blazer

1 Answer

Chevy blazer brake pedal going to the floor when engine is running


has to be air,try bleeding without the brake pedal,just open
the bleeders and let gravity run the fluid out,takes awhile but works.
(master cyl.cover off )

Dec 25, 2012 | 1999 Chevrolet Blazer

1 Answer

Brake pedal gos to floor. i have replaced pads master cylnder. bleed numerous times


Hi and welcome to FixYa!

Please do bleed the rear brakes too for the air to pass. If the fluid spits solid and the pedal still goes to the floor I strongly suggest that you have the hydrovac be replaced. This is the last thing to replace that can make the brakes go back to it's normal operation.

Hope you find this information helpful enough and thank you for using FixYa! Have a good one!

Jan 31, 2011 | 2000 Chevrolet Blazer

1 Answer

Brakes to the floor(almost) 99 blazer


bleed the brake again. if the pedal goes to the floor with little resistance, then the master cylinder is your problem.
the shim is to depress the noise when you applied the brake. you can skip that, if the brake works without it.

Apr 29, 2009 | 1999 Chevrolet Blazer

2 Answers

I need to know how to bleed the brakes on a 1999 chevy blazer


Start from right rear, then, left rear, right front, left front. Fill master cylinder. Have helper sit in car, have helper hold brake pedal down. open bleed screw. fluid and air comes out. close screw. release brake pedal. Continue until no air comes out. Move to next wheel. Keep an eye on master cylinder fluid level after each wheel.

Mar 27, 2009 | 1999 Chevrolet Blazer

1 Answer

Emergency brake foot pedal not working


Sounds like the cable is stuck also check the catch on the foot pedel

Mar 13, 2009 | 1999 Chevrolet Blazer

1 Answer

1999 Chevy S10 Blazer 4x4. Replacing rear pad's,& Bleeding Breaks


have one person in the blazer pumping the brake pedal and then hold to the floor, crack the bleeder then tighten, release pedal, repeat till all air is out one side at a time, if this does not work then your ABS unit is bad witch if u follow your lines from your master cylinder u will find a black box with a motor on it, or the master cylinder itself is bad, it also can cause u to have no pedal, replace the master cylinder first, most likely cheaper.

Mar 11, 2009 | 1997 Chevrolet S-10 Pickup

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...