Question about 1990 Toyota Corolla

1 Answer

When replacing a spark plug tube gasket, do you need to seat the gasket on the spark plug tube or in the cylinder head cover?

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 242 Answers

As far as I know there is no gasket we use sealant, we use a socket the same diameter that the tube then, the tube is spanned with pliers, the socket inside help the tube so don't get deformed.
when the tube is out clean the treads apply fpg (toyota silicon gasket) re-install.

Posted on Jan 02, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to remove valve cover on 2000 Camry Toyota


For the four cylinder engine:

  1. Remove and label all electrical wiring, connectors and vacuum hoses necessary to gain removal clearance.
  2. Remove the spark plug wires. Disconnect the PCV hose.
  3. Remove the four nuts and grommets located on top of the cylinder head cover.
  1. Remove the cylinder head cover and the cover gasket from the cylinder head.
  2. Discard the gasket and replace with a new one.
To install:
  1. With a wire brush or gasket scraper, remove all the old gasket material from the cylinder head and the cylinder head cover gasket surfaces.
  2. When the cylinder head surfaces are free and clean, apply beads of sealant to the cylinder head in the locations shown in the accompanying illustrations.
  3. Install the new cylinder head gasket in the cover. Make sure that the gasket seats evenly.
  4. Place the cylinder head cover with the gasket onto the cylinder head.
  5. Install the four grommets and nuts. Uniformly tighten the nuts in several passes to 17 ft. lbs. (23 Nm).
  6. Connect the PCV hose. Connect all removed vacuum hoses, connectors and electrical wiring. Connect the negative battery cable.
  7. Start the engine and inspect for oil leaks.
  8. Repair any leaks as necessary.
For the V-6 (3.0L) engine:
  1. Drain and recycle the engine coolant.
  2. Disconnect the radiator inlet hose.
  3. Disconnect the throttle and accelerator cables.
  4. Remove the air cleaner cap assembly.
  5. Remove the V-bank cover. Use a hexagon wrench to loosen the nuts.
  6. Label and remove all emission control valve hoses. Disconnect any wiring interfering with the valve cover removal.
  7. Remove the air intake chamber. This will gain you access to the back valve cover.
  8. Disconnect the engine wire from the left hand side, No. 3 timing belt cover, rear side and right hand side. Most of the wiring is secured by nuts and or bolts to the body of the vehicle.
  9. Remove the ignition coils, make sure the place them in order on a table so not to mix them up.
  10. Remove the 8 bolts retaining the valve covers and gasket.
  11. Clean the mating area of the valve cover and cylinder heads well. If necessary, scrape any left gasket from either surface.
  12. Apply seal packing to the cylinder heads and place new gaskets into position.
  13. Attach the valve covers. Uniformly tighten the bolts in several passes to 69 inch lbs. (8 Nm).
  14. Install the spark plugs in their proper locations, then place the ignition coils into place and secure.
  15. Attach all engine wiring be sure to secure each harness properly.
  16. Install the air intake chamber. Refer to Fuel System .
  17. Attach all emission hoses and wiring.
  18. Attach the V-bank cover.

Apr 15, 2014 | 2000 Toyota Camry

2 Answers

Oil on spark plugs?


Hi. If you mean oil is around the top of the plug (the porcelian and hexigan part the plug)
This is usually the gasket between rocker cover and cylinder head.
I think on the honda its a rubber gasket/seal
I hope this helps you and it should not be to exspensive
Good luck John ( South Wales UK)

Apr 16, 2011 | 1991 Honda Accord

1 Answer

Oil get into spark plug well. need to know how to replace the valve cover gasket on a 2003 dodge intrepid sxt . clean sparkplugs well of all oil and replaced sparkplugs


Hi
these are the things you need to do.

Allow the car engine to cool by letting the car sit idle for several hours. Lift the hood and disconnect the negative battery cable. Remove the upper intake manifold assembly. Using the spark plug tool, remove the spark plugs. Disconnect the spark plug wires. This can be accomplished by pulling straight out on the boot. Locate the cylinder head and disconnect the closed ventilation system and evaporation control system from it.

Locate the left cylinder head cover and remove the DIS coil. Using the wrench, loosen and remove the rocker arm cover mounting bolts. Carefully remove the rocker arm cover from the cylinder head. Remove the gasket cover. Using the screwdriver, gently nudge the gasket to remove it from the seating area.

Using the automotive cleaner, remove any particles, oil or other remnants that were left by the old gasket. Place the new gasket in the gasket seating area. Using the torque wrench, tighten the rocker arm cover fasteners. Reverse the steps used to remove the parts

Complete the maintenance by adding oil to the car and allowing it to run idle for 10 to 15 minutes.

Feb 22, 2011 | Dodge Intrepid Cars & Trucks

2 Answers

Valve cover gasket, how to replace?


Rocker Arm (Valve) Cover REMOVAL & INSTALLATION 2.3L 4-Cylinder Engines
  1. Disconnect the negative battery cable.
  2. Label and remove the spark plug wires.
  3. Remove the attaching bolts for the valve cover.
  4. Remove the valve cover from the cylinder head. If necessary, lightly tap the valve cover with a soft hammer to aid in removal. To install:
  5. Thoroughly clean the valve cover and cylinder head gasket mating surfaces.
  6. Install the valve cover on the cylinder head using a new gasket.
  7. Tighten the valve cover bolts to 14 ft. lbs. (20 Nm) in a crisscross pattern.
  8. Install the spark plug wires.
  9. Connect the negative battery cable.
  10. Start the engine and check for leaks. Fig. 1: Valve cover and gasket assembly 90953g12.gif
2.8L 6-Cylinder Engine
  1. Disconnect the negative battery cable.
  2. The following steps are necessary if your car has A/C and if you are removing the passenger side valve cover, if you do not need to remove the passenger side valve cover, skip them.
    1. Remove the A/C compressor belt and the compressor from the mounting bracket located on the passenger side of the engine. Do not remove the lines from the compressor.
    2. Place the compressor with the lines attached on the passenger side front shock tower and secure.
    3. Remove the compressor bracket.
  3. Remove the air cleaner-to-throttle body hose.
  4. Label and remove all necessary electrical and vacuum connections.
  5. Remove the attaching bolts for the valve cover(s).
  6. Remove the valve cover(s) from the cylinder head(s). If necessary, lightly tap the valve cover with a soft hammer to aid in removal. To install:
  7. Thoroughly clean the valve cover(s) and cylinder head gasket mating surfaces.
  8. Install the valve cover(s) on the cylinder head(s) using new gaskets.
  9. Tighten the valve cover bolts to 11 ft. lbs. (15 Nm) in a crisscross pattern.
  10. Install all necessary electrical and vacuum connections.
  11. Install the air cleaner assembly.
  12. Install the A/C bracket (if removed).
  13. Install the A/C compressor and belt (if removed).
  14. Connect the negative battery cable.
  15. Start the engine and check for leaks.
2.3L and 2.4L 5-Cylinder, and 2.9L 6-Cylinder Engines The 2.3L and 2.4L 5-cylinder, and 2.9L 6-cylinder engines have a two-piece cylinder head, the upper half and the lower half. The upper half is basically the same as a valve cover, except that it incorporates the bearing caps for the camshafts into the underside.
  1. Disconnect the negative battery cable.
  2. Remove the spark plug access cover.
  3. Label and remove the ignition coils and vent hoses or the distributor cap and wires if equipped.
  4. Check the cam alignment before removing the cylinder head.
  5. Remove the bolts attaching the upper cylinder head.
  6. Remove the upper cylinder head, lightly tap with a soft hammer if necessary. To install:
  7. Thoroughly clean the upper and lower cylinder head gasket mating surfaces.
  8. Apply liquid sealing compound to the upper cylinder head mating surface. WARNING
    Use a roller or your finger to spread sealant, do not use an excessive amount of sealant, or the oil passages could become clogged.
  9. Place the upper cylinder head onto the lower cylinder head.
  10. Check the cam alignment before tightening the cylinder head.
  11. Install Volvo tool number 5454 or equivalent to the upper cylinder head.
  12. Tighten the nut on the tools to seat the upper cylinder head.
  13. Tighten the upper cylinder head bolts, beginning from the center out to 13 ft. lbs. (17 Nm).
  14. Install the ignition coils and hoses or the distributor cap and wires.
  15. Install the spark plug access cover.
  16. Connect the negative battery cable.
  17. Start the vehicle and check for leaks. Fig. 2: Remove the clamp and detach the vent hose 90953p66.jpg
    Fig. 3: Remove the spark plug cover and the plug wires or ignition coils to access the retaining bolts 90953p80.jpg
    Fig. 4: Remove the retaining bolts 90953p72.jpg
    Fig. 5: A light tap with a soft-faced hammer is usually required to loosen the valve cover 90953p81.jpg
    Fig. 6: Carefully lift the upper cylinder head up and off the lower section. Note the integral camshaft bearing caps in the casting 90953p82.jpg
prev.gif next.gif

Jan 29, 2011 | 1999 Volvo S70

6 Answers

I have a 2002 Nissan Altima 2.5L that is leaking oil into the spark plug tubes; can these seals be replaced or does the valve cover have to be replaced?


Yes, you need a Rocker cover (valve cover) Gasket kit. Remove the valve cover, remove all old O-rings and cover gasket, clean grooves and mating surfaces without gouging or scratching them, put the new gaskets on as per factory recommendations, tighten to the proper torque and you're done. The spark plug holes in the cover are part of the valve cover gasket kit. Any Napa, Car Quest, Pep Boys, Auto Zone will have it.

Oct 03, 2010 | 2002 Nissan Altima

2 Answers

Cause of oil in sparkplug tube?


1.your valve cover's spark plug chamber seal is leaking. Which requires removing the valve covers and replacing the gaskets and seals. 2. Excessive oil spills on to the valve cover and ignition coils when adding oil.

**This excess oil on the plug boots can cause the coils to short and eventually fail.

Apr 20, 2010 | 2001 Lincoln LS

5 Answers

Head Gasket?? Valve cover Gasket???


most likely it is the valve cover gasket. it covers the valve train where there is alot of oil to lube the top of the motor. if the head gasket was leaking it may have more signs of running poorly. also having coolant leaks also. so i will have to say valve cover gasket. now usally you may have a oil burning smell with it depending on the area of the lek but not always.

the valve cover can easily be seen when the hood is open. it is right on the top and where it meets the clyinder head is where the gasket is and the leak can be seen.

if you have more question please ask.

Nov 12, 2009 | 1997 Geo Tracker 2 Door

1 Answer

How to change out valve cover gaskets on a 1989 Lincoln Town Car


This is All you need for this Repair, ALSO Be Sure ALL GASKET SURFACES ARE VERY CLEAN. This Engine Requires MORE than MOST ALL Engines do for this Repair.

REMOVAL

  1. To remove a valve rocker arm cover from the RH cylinder head, disconnect PCV closure tube from oil fill stand pipe at rocker cover.
  2. Remove the Thermactor bypass valve and air supply hoses as necessary to provide clearance.
  3. Disconnect the spark plug wires from the spark plugs using Spark Plug Wire Remover T74P-6666-A or equivalent. Do not pull on wire. Remove the wires and bracket assembly from the rocker arm cover attaching stud and position the wires out of the way. ALSO MARK THEM AS TO WHERE THEY CAME FROM !!!
  4. Remove upper intake manifold.
  5. Remove attaching bolts and remove the cover.
INSTALLATION

  1. Clean the valve rocker arm cover(s) and the cylinder head gasket surface(s). Position a new service valve rocker cover gasket.
  2. Position the cover(s) on the cylinder head(s). The cover is tightened in two steps. Tighten the bolts to 14-18 N.m (10-13 lb-ft). Two minutes later, tighten the bolts to the same specification.
  3. Install the crankcase ventilation tube in the RH cover.
  4. Install upper intake manifold.
  5. Install the spark plug wires and bracket assembly on the rocker arm cover attaching stud. Connect the spark plug wires. Install the air intake duct assembly.
  6. Install the Thermactor bypass valve and air supply hoses (if required).

Oct 03, 2009 | 1989 Lincoln Town Car

2 Answers

Oil leaking out of valve cover gasket


It is a Valve Cover Gasket. You can get a new one at any Auto Parts Store. To make this repair last longer, Do not get the Cheap one, Get a Felpro Gasket and it will Quadrupel the Gasket Life. Please Rate My Response! Thanks!

Jan 30, 2009 | 2001 Kia Sportage

Not finding what you are looking for?
1990 Toyota Corolla Logo

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...