Question about 2001 Chevrolet Impala

1 Answer

When starting the engine the coolant light comes on but the coolant level is where it should be. The temperature gauge is working properly. Is there a reset for the light after adding coolant?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 75 Answers

As i know of there are no resets for the cooland light most of the time you can take something soft and the container where the antifreeze goes hit it a couple of time just enough to jar it a little and the light will go off if that doesnt work then your sensor inside the container is bad in which case you will have to replace it, One of these suggestions should turn out the light. hope this helped.

Posted on Jan 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Broken temp gauge 2000 4.2V6 f150 were Is THE sending unit


Does your vehicle have a hard start first start up in the morning ? Does the vehicle shift properly ? Is the check engine light lit.?
I would not think the sending unit was bad if your not experiencing any of these type problems , I would think the gauge was bad ! You need to know how this works , the coolant temp. sensor is an input to the PCM - engine computer . The PCM use this info for more then just setting the gauge to the proper temp. It is used for proper shift points , how much fuel the PCM supplies to the engine etc.
Engine coolant temperature information is received by the instrument cluster from the PCM over the SCP network. Temperatures over 121°C (275°F) will display hot (H). If the engine coolant temperature data is missing or invalid for five seconds, the instrument cluster will move the engine coolant temperature gauge below the cold (C) position.
The SCP - a serial data communication network !

Oct 19, 2015 | Cars & Trucks

1 Answer

Temperature gauge


Temperature gauges will not work properly unless there is water in the radiator. For the light to come and the length of time it takes to work I would be checking the coolant level at the radiator cap first then checking the operation of the temperature sender unit.

Oct 26, 2013 | Cars & Trucks

1 Answer

1999 VW Cabrio dash light


Obviously it's temperature gauge light. Check for coolant level first. Then check for coolant leak. If coolant is leaking out of your car, the lower coolant levels in your engine will cause it to overheat. If you have your heater on and it starts blowing hot air instead of cool, your engine is low on coolant. This will cause to flash a warning light on your car's dashboard.

Jun 10, 2013 | Cars & Trucks

3 Answers

I have a 2004 durango 5.7l hemi that makes loud knocking rattling noise when started but cuts off right away. No codes could be found fro OBD. Oil level is fine, just a little dirty. Don't know wha


Engine noises don't leave fault codes unless the knock is so bad the engine is misfiring. When you say it "cuts off right away" do you mean the engine stalls or the knock goes away? If the answer is the knock goes away right away then you have a crank or rod bearing that is loose from wear, the oil pressure fills the excess bearing clearance gap and the knock stops.

Nov 22, 2011 | 2004 Dodge Durango

1 Answer

No my alero is overheating. I have replaced the thermostat and waterpump and put a new cap on reservior and im losing coolant out the overflow


YOU NEED BLEED AIR OUT THE COOLING SYSTEM.WAIT TO ENGINE COOL DOWN.YOUR VECHICLE YOU HAVE TO POUR COOLANT IN THE COOLANT OVERFLOW JUG UNTIL COOLANT LEVEL STAY AT THE FULL COLD MARK.THEN START ENGINE LET IT IDLE A FEW MINUTES WATCH COOLANT IN THE OVERFLOW JUG WHEN IT DROPS ADD MORE COOLANT UNTIL COOLANT LEVEL STAY AT FULL COLD MARK.WHEN COOLANT LEVEL STOP DROPPING IN OVERFLOW JUG.SCREW RADIATOR CAP BACK ON OVERFLOW JUG WATCH ENGINE COOLANT TEMPERATURE GAUGE AS COOLANT TEMPERATURE START CLIMBING TURN OFF ENGINE LET IT SET A WHILE KEEP FROM GETTING SCALDED.TAKE LARGE RAG PLACE OVER COOLANT OVERFLOW JUG CAP SLOWLY OPEN RADIATOR CAP A LITTLE AT A TIME UNTIL PRESSURE RELEASE.REMOVE OVER FLOW JUG CAP.ADD MORE COOLANT UNTIL COOLANT LEVEL AT THE FUL COLD MARK ON THE OVERFLOW JUG.THEN SCREW CAP BACK ON THE OVERFLOW JUG.START ENGINE LET IT IDLE AGAIN WATCH ENGINE COOLANT TEMPERATURE GAUGE WHEN TEMPERATURE GAUGE START CLIMBING.TURN OFF ENGINE WAIT A WHILE.CHECK COOLANT LEVEL IN THE OVER FLOW JUG.DO THIS PROCEDURE UNTIL THE COOLANT LEVEL IN THE COOLANT OVERFLOW JUG STOP DROPPING AND STAY AT FULL COLD MARK,WHEN THE TOP RADIATOR HOSE GET HOT THERMOSTAT OPENING AIR IS OUT THE COOLANT SYSTEM. WHEN ENGINE COOLS DOWN.CHECK COOLANT OVERFLOW JUG COOLANT MUST BE IN THE COOLANT OVER FLOW JUG AT THE FULL COLD MARK WHEN ENGINE COLD. DONT .DONT OVERFILL COOLANT OVERFLOW JUG.KEEP COOLANT IN THE OVERFLOW JUG IF YOU LET COOLANT OVERFLOW JUG RUN DRY AIR WILL BE DRAW IN COOLANT SYSTEM CAUSE ENGINE TO OVERHEAT.

Aug 12, 2011 | 1999 Oldsmobile Alero

1 Answer

I let my car heat up to get frost of window for about fifteen minutes. When I went out the frost was still on window and no heat coming from dash and car was overheating. I shut it off, let it cool down...


Start with engine cool, remove rad cap, start engine and turn heater on. Top up rad level and Let engine run until it get's up to normal operating temperature with cap off and add coolant as you see it go down. Watch in rad for coolant to start moving quicker, once gauge gets close to normal temperature, indicating that thermostat has opened. Wait until you see that 2 or 3 times, then top up and install rad cap. Top up coolant return bottle to proper level . You'll want to keep a close eye on coolant return bottle level for next little while. If coolant got that low in the first place, you have a leak somewhere that will have to be found.

Mar 31, 2011 | 2002 Chevrolet Impala

1 Answer

Heater on and working - temperature gauge normal. Heater starts to blow cold and temperature gauge goes to full hot and overheated coolant light comes on. Coolant overflow tank full and upper/lower...


one of two things could be happening... either the radiator is low on coolant or your thermostat is stuck (which if it is stuck you will have to replace) . But first let engine cool down, you need to check coolant level, squeeze one of the radiator hoses even if engine is cooled down to make sure there is little or no pressure in cooling system then remove radiator cap/coolant bottle cap to check level.by the way if it is low you will need to figure out why.. the obvious reason is a leak you may have to go to a shop and have system pressure tested to locate leak to repair.. good luck to ya.. hope this helps

Mar 20, 2011 | 2005 Buick Rendezvous

2 Answers

99 couger 2.5L 6 Cyl-temp gauge maxing out, overheating


I will normally remove rad cap when cool. Start engine, set heater in car to heat & turn on blower, if you use defrost setting, the rad fan &/or AC fan will come on, and you don't want that. Then while running with cap off, make sure coolant in rad is an inch or 2 from top of rad, and let it run. When engine gets to normal operating temperature on the gauge, you'll start to see more flow in radiator, and rad fan should come on shortly after, to cool the incoming hot liquid in the rad, that tells you the thermostat opened as it should, and the process starts again, engine coolant gets to temp, thermostat opens, hot goes to top of rad for cooling, and cooler liquid goes out the bottom to engine, etc etc. If your heater is not on while doing this, the coolant doesn't get to heater core in most cases, thus creates an airlock, or will cause level in rad to go down when it is turned on, and thus reduces amount of coolant in rad, plus airlocks in the entire system. So, let it run to the point that the rad fan comes on & off on it's own, about 3 times, while you watch the gauge, to make sure it doesn't overheat, if it does, shut it off and let it cool down & try again. if all appears good, top rad up if needed to an inch or so from top, put your cap on properly, add coolant to proper level in return bottle & try it and see what happens. Remember though, I am assuming thermostat was put in correctly, rad in good shape, fan is working properly as well as water pump doing it's job. If this method doesn't work, get back to me with results.

Feb 16, 2009 | 1999 Mercury Cougar

Not finding what you are looking for?
2001 Chevrolet Impala Logo

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...