Question about 1995 Jeep Grand Cherokee

Open Question

1995 jeep 4.0 crankshaft position sensor ohms?? Cannot find information online.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 41 Answers

SOURCE: my 1996 jeep cherokee sports

The CPS is one of the first places to start, but remember that the signal goes thru the ECM first, which ultimately supplies power to the coil, I've had to replace the ECM on my 96 Grand Cherokee 4.0 3 times. The dealer wanted to replace the crack and cam sensors, but it was only the computer that was bad.  Sorry I cant give you any definitive answers but I did get it to turn over when I hit the computer with a wrench!

Posted on Dec 12, 2008

Ad
  • 41 Answers

SOURCE: no spark

Check the asd relay in the fuse block. Replace it with a known good relay

Posted on Apr 26, 2009

  • 10 Answers

SOURCE: location of crankshaft position sensor Jeep grand cherokee 1997

left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Posted on Jun 13, 2009

  • 285 Answers

SOURCE: crankshaft sensor located 98 jeep grnd cher 4wd 6cy

it is located at the back of the engine on top of the transmission bell housing,the plug runs over to the passenger side of the engine bay and it comes out from behind the engine,you can actually get your hand on the sensor itself from under the hood on the drivers side,and i believe its a 13mm bolt holding it in,the new sensor will have a sticker on the end of it...leave it there,it is used for correct spacing between the sensor and the flywheel,hope this helps

Posted on Sep 23, 2009

Testimonial: "Everything was just like you said but as a not atleast for my jeep it is an 11mm not 13mm. Works great so far (keep fingers crossed) "

emissionwiz
  • 76846 Answers

SOURCE: replace a crankshaft position sensor on a 1996

1st I need to know what engine you have, 4.0L or 5.2L V8.

Posted on Oct 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE TO CHANGE OUT A CRANK SENSOR IN MY GRAND CHEROKEE.


Jeep Crank Sensor Replacement, P Codes P0351, P1391 ...

? 6:24
www.youtube.com/watch?v=7D0vUEDSwXo
May 12, 2013 - Uploaded by Robert DIY Replaced the crank sensor on this 2003 Jeep Grand Cherokee.... to replace my crankshaft position sensor on my 1998 grand cherokee laredo.

Jeep Crankshaft Position Sensor Replacement (CKP, CKPS ...

? 4:07
www.youtube.com/watch?v=1Ho5iAKQV00

Oct 27, 2013 - Uploaded by WeekendHandymen
hi , do you think if I replace crank sensor will solve the problem ,my jeep .... Where's the crankshaft located in 99 jeep grand Cherokee laredo .


Oct 24, 2015 | Cars & Trucks

1 Answer

Crankshaft position sensor 4 0l


New Crank shaft sensor,& new battery, (check cables) may need ecu reflashed

Jan 04, 2014 | 1995 Jeep Grand Cherokee

2 Answers

Replace a crankshaft position sensor on a 1996


1st I need to know what engine you have, 4.0L or 5.2L V8.

Oct 02, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Need to know what fires coil 1995 mercury sable both wires to coil have power when key is turned on car cranks no spark from coil new coil what gives the coil extra power to fire


what engine? 3.0L 2 Valve? 4 Valve?
3.4L SHO engine?

The PCM (engine computer) fires the coils, but it is never the cause of a problem. I suspect it is the crankshaft position sensor on the front of the engine by the crank pulley. easy to change.

Crankshaft Position Sensor The crankshaft position sensor (CKP sensor) (6C315) is a variable reluctance sensor triggered by a 36-minus-1 tooth trigger wheel located on the crankshaft pulley and damper. The signal generated from the crankshaft position sensor is called the crankshaft position (CKP) signal, which provides base timing and crankshaft speed (rpm) information to the ignition control module (ICM) (12K072). Base timing is set at 10±2 degrees before top dead center (BTDC) AND IS NOT ADJUSTABLE. The powertrain control module (PCM) (12A650) will use this information with the spark advance information to determine ignition coil (12029) turn on or turn off time.

Sep 15, 2009 | 1995 Mercury Sable

2 Answers

I have a 1988 jeep with intermitent spark


replace the crankshaft position sensor, located at bell housing driver side.

Jul 06, 2009 | 1988 Jeep Wrangler

1 Answer

Locate crankshaft position/crank angle sensor


The crank posistion sensor is located on the top of the transmission bell housing right next to the motor, its a @$^&^ to get to and do without a lift,

Jul 02, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Location of crankshaft position sensor Jeep grand cherokee 1997


left rear of engine block,on transmission bell housing.best way from top under brake booster use a wrench,

Jun 13, 2009 | 1995 Jeep Grand Cherokee

2 Answers

CANT FIND CRANK SENSOR


The sensor is mounted in a fixed position in the engine block. The tip of the sensor protrudes into the crankcase at a distance of 0.05 plus or minus 0.02 inch from the crankshaft.

Apr 28, 2009 | 1995 Jeep Grand Cherokee

1 Answer

I CANT LOCATE CRANK POSITION SENSOR


7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
7X Crankshaft Position (CKP) Sensor
Lower rear of engine
4
25
--
24X Crankshaft Position (CKP) Sensor
Right hand side of engine, at end of crankshaft, behind harmonic balancer
Right hand side of engine, at end of crankshaft, behind harmonic balancer

Apr 12, 2009 | 1995 Chevrolet Monte Carlo

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...