Question about 1991 Toyota Camry

2 Answers

Need direction / assistance on how to remove and replace the power steering pump on 1991 Toyota Camry 4 cyl 3sfe. I am not a pro, but I think I can handle this as DIY project . Also, does the same belt that runs the altenator, water pump, A/C also drive the Power steering pump, or does it use another belt? I think I have enough tools, but if you know the sizes I need, that will help. Thanks, Bill Chase

Posted by on

  • Bill Chase Jan 03, 2011

    The diagram did not show up...please re=send....also answer belt question.....also , what do I have to remove under the car to get access to the pump.... do you know 1991 Camry ? Thanks

  • Bill Chase Jan 03, 2011

    No diagram has come through yet...please try again...thanks

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,299 Answers

This is a pretty in depth job. I can tell you how to do it, but I would be going off of memory. And could leave important steps out. I would be going off of memory. The best suggestion that I can give is to go to your local library and check out the Chilton's or Haynes Manual. This will give step-by-step illustrated instructions. As far as tools go, you will need a set of metric sockets, both flat and phillips head screwdrivers, a pair of channel-locks or water pump pliers, and a set of metric wrenches. Also if you have a swivel for your sockets and an extension will both be very helpful. The belt that turns the power steering is the same belt that turns everything else. It is called a serpentine belt. There will be a tensioner to get the belt off. Make sure that you draw yourself a diagram of how the belt goes. Sometimes I have seen in the manuals a different routing than the actual routing.

Posted on Jan 03, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 144 Answers

Hi, 1st lets disconnect the neg side of battery to be safe. Here is a diagram that will help you a deep well socket will make it easier for you. next take off pwr steering belt off ,then disconnect lines to pwr steering pump , then remove the bolts that holds pump on and replace with new . put back in reverse order. If you need any more info just re post.
Thanks dodge tec


The diagram shows the pump and the bolt location.

Need direction / assistance on how to remove and - 192750_powersteeringbelt91camry6cylfig09_1.jpg

Posted on Jan 02, 2011

  • dodge tec Jan 03, 2011

    Hi, 1st lets disconnect the neg side of battery to be safe. Here is a diagram that will help you a deep well socket will make it easier for you. next take off pwr steering belt off ,then disconnect lines to pwr steering pump , then remove the bolts that holds pump on and replace with new . put back in reverse order. If you need any more info just re post.
    Thanks dodge tec

  • dodge tec Jan 03, 2011

    hope you can see it now having problems with my scanner. my shows two belts . you should not have to take nothing off bottom to remove pump. if u cant see every thing it will be tomorrow before im in my shop and can use that computer to send more info . sorry

    The diagram shows the pump and the bolt location.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota Camry 1993 4 cyl water pump failing, have removed thermostat, considering Electric inline pump as replacement as option ? Please advise me of pro's and con's.


i owned the 1995 4 cyl wide body camry till the cooling system failed in heavy traffic and over heat stripped out the head bolt threads in the block

the toyota camry engine designation is a 5S-FE

water pump is driven by timing belt
behind timing belt covers
they have to be removed to get to the water pump

normally timing belt, seals ,tension er pully and water pump are replaced at the same time ..comes in a kit

i dont have the 5S-FE cooling system hot under pressure specs

so I cant answer which inline electric pump pressure is required to work on the 5S-FE


engine repair manual free download pdf
5S-FE 431 pages
http://www.turboninjas.com/camry/eg1.pdf
ENGINE MECHANICAL to page 144
EMISSION CONTROL SYSTEMS
MFI/SFI SYSTEM page 164
COOLING SYSTEM page 238
LUBRICATION SYSTEM page 268
DIAGNOSIS SYSTEM page 296
CIRCUIT INSPECTION page 336
water pump as a part

timing belt water pump kit
water pump
,location on the engine with timing covers removed


e7622159-98af-4a83-8989-bd6dd48bcde3.jpg26279563-dp42dlzfhn4dbdhi1rc14q4e-1-2.jpg26279563-dp42dlzfhn4dbdhi1rc14q4e-1-3.jpg

Sep 10, 2016 | 1993 Toyota Camry

2 Answers

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ?


Where is the crank position sensor on a 95 Toyota celica gt 2.2

search.aibing.cc/Where+is+the+crank+position+sensor+on+a+95+Toyota...
P1335, No Crankshaft Position Sensor Signal - Engine Running. ... 91 1991 ToyotaCelica GTS Engine Mount Right 2.2L 4 Cyl Genuine. ... 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001 . ... Powered by a 2.2-liter engine, the Celica now had ST and GT trim models. ... in 1986 and a 2.0-liter ...

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ...

www.fixya.com/cars/t26080657-crank_position_sensor_1994_toyota
31 mins ago - It is not behind pully nor in dist all videos show - Toyota Cars & Trucks question. ... Change a crankshaft position sensor on a 2000 eclipse.

toyota camry crankshaft sensor - ABMforum.com

abmforum.com/toyota-camry-crankshaft-sensor.html
toyota camry crankshaft sensor 99 camry crankshaftcamshaft position codes i got a problem with my 97 ... The car 96 toyota camry 2.2 liter 4 cyl. ... 1994 toyota camry 2.2L 257k miles Symptoms Car overheats Top radiator hose hot bottom cold ...

Toyota Camry 5SFE Engine Timing Belt, Water Pump and ...

hubpages.com > Autos > Do It Yourself Auto Repair
Jul 10, 2014 - The Toyota 5SFE motor is a four-cylinder, 2.2 liter, timing-belt-driven, double ..... Remove the lower timing belt cover with the crankshaft position sensor. ..... I've never, ever replaced the harmonic balancer on a 4cyl 5SFE.

1995 Toyota Camry LE 4 cylinder - YouTube

? 2:27
https://www.youtube.com/watch?v=7TW6hlUiHWQ
Sep 6, 2011 - Uploaded by jacasan2000

Feb 03, 2016 | Toyota Cars & Trucks

1 Answer

Toyota camry 1991 4 cyl auto power steering belt has come off pulley how do I get it back on?


There is either a pulley that acts like a tensioner or the pump will pivot when loosened. Look for slots on the pump and pulley brackets. Loosen bolts, install new belt, tighten belt then bolts. As an additional note, there is likely something else wrong (that is why the belt came off).

Aug 30, 2011 | Toyota Camry Cars & Trucks

1 Answer

Hi, my 1990 Toyota Camry with 3S-FE engine noises on timing belt side recently. I got my timing belt and water pump changed in 2006 December. So far I drove the car around 50,000km. I changed my power...


I had the same problem in my 3sFE, I thought the same way you did, but it turn out to be the fan, check if there is any play in the fan, change it and your scrutching noise will be no longer there


Asadullah

Oct 24, 2010 | 1990 Toyota Camry

1 Answer

1991 toyota camry 4 cyl. how to change fuel pump.


I saw this DIY site on how to replace the fuel pump of the 1992 Toyota Camry. This solution can be used in all vehicle types.

http://www.automd.com/62/how-to-replace-a-fuel-pump/

Feb 03, 2010 | 1991 Toyota Camry

1 Answer

Need to know how to replace water pump in 1992 6 cyl Toyota Camry


Miss sexy girl, do you want step by step instructions because I can direct you to the place to get them, It is not very easy, but if you can follow directions, I can tell you where to get them, I make no money sharing my expertise and will help you every step of the way through getting your car fix. My rating is all I gain in return. Please help me to increase it...thanks I can help you save money for free.

Dec 19, 2008 | 1991 Toyota Camry

Not finding what you are looking for?
1991 Toyota Camry Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...