Question about 2002 Chevrolet Silverado 1500

1 Answer

What is the torque on pinion nut for a 2002 1500 silverado with a rebuilt rear end?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 144 Answers

HI, If you have a gmc axel pinion seal nut torque is 270 FT.LBS or 366 NM
If you have a dana axel pinion seal nut torque is 255 FT.LBS or 346 NM
If i can help you anymore just re post
Thanks dodge tec

Posted on Jan 02, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need the pinion nut torque for a 1990 ford ranger


I believe your rear end uses a crush sleeve. You have to shim your pinion gear to the proper depth first, then you have to crush sleeve (impact gun helps), then measure the torque ( inch pounds I believe) it takes to rotate the pinion gear. If you don't have the right equipment to set up your rear end, take it to a shop.

Nov 12, 2015 | Ford Cars & Trucks

1 Answer

What is the torque specification for the pinion nut and 1960 Chevy Impala


We are talking rear end hear correct . However torque isn't spicific to vehicles what it is spicific to is the grade of the metal V S the treard pitch V S the size of the shaft and nut .Most poinion nuts are what is called flange nuts witch means there is a base on the nut and you need 2 differant wrenches to install or remove one to hold one side and the other to break it free on tighten .The problem here is its hard to know with a torque wrench on the nut and an open end wrench on the pinion side . So take to big open ended wrenches and crank them together as tight as you can . this gives you x2 torque but the spec about 65 ftlbs to 90 lbs for most although you will not be able to measure acuralty

Mar 17, 2015 | Chevrolet Impala Cars & Trucks

1 Answer

What is the torque spec for a 1978 Ford pinto differential pinion nut?


170 ft.lbs is the minimum; be aware that this differential uses a crush sleeve to set the backlash and the pinion torque is what crushes the crush sleeve. If you don't set the backlash correctly you can grind up your differential gears.
8 Inch Ford Rear End Torque Specifications eHow

Feb 02, 2015 | Ford Cars & Trucks

1 Answer

What size socket is needed to remove rear pinion nut on 1997 jeep grand Cherokee limited with a5.2 v8


the rear axle front pinion DANA 44 or AMC?
the answer is not simple , why not read the FSM and unstand it all.
experpted....
  1. On 1990-98 models, set bearing preload as follows:
    1. The required pinion gear bearing preload torque is 1/2 ft. lbs. over the noted release torque as measured above.
    2. Rotate the pinion gear three or four times with a torque wrench attached to the yoke nut. Measure the amount of torque necessary to rotate the pinion.
    3. Using a holding tool, tighten the yoke nut in small increments and remeasure until the specified torque is obtained.



$15
alldata.com
or
free
here
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service
see diff chapters. its non trivial.

Oct 01, 2014 | 1997 Jeep Grand Cherokee

1 Answer

What are torque specs on 1965 ford 7 and 1/4 inch rear


I have a '68 Motor's manual (goes back to'58) the only rear end specs I can find are for the pinion nut (140 ft. lbs.)
pinion preload: 17-27 in. lbs. w/integral carrier or 22-32 in.lbs. w/ removable carrier. Tightening the carrier bearings isn't so much a torque setting but more or a tightening procedure. Theses specs are done during the rebuild so I wonder if you're asking about the bearing caps or bolts that hold the diff. to the axle housing? I could not find a spec. for bolt torque. Since the bolts that hold it in (if that is what you asking about) are not a bearing adjustment, you can go with a generic torque based on bolt size. Again, I'm not sure what component, or bolts it is you are asking for torque specs on.

Sep 17, 2014 | Cars & Trucks

1 Answer

Rear end is leaking fluid where it connects to the drive shaft


you mean rear axle pinion seal. to change it you need to remove driveshaft. take a torque wrench to see the running torque. then remove center nut ,remove yoke. with screwdriver remove seal; reverse proc. then tight center nut to torque you find before you remove the center nut.

Sep 21, 2013 | 2001 GMC Jimmy

1 Answer

I need 2004 dodge ram 1500 rear pinion nut torque rating, ...


you need to know what rear end you have if it's a 8.25, 8.37, or 9.25 the pinion nut torque is a minimum of 210 ft. lbs.


if you have the Dana model 44 190-290 ft. lbs.

if you have a Dana model 60 215-315 ft. lbs.

Apr 27, 2011 | 2004 Dodge Ram 1500

1 Answer

Pinion nut torque spec chev


Axle Preload and Backlash Specifications 8.0 Axle Preload and Backlash Specifications Application
Specification
Metric
English
Backlash
0.08-0.25 mm
0.003-0.010 in
Backlash (Preferred)
0.13-0.18 mm
0.005-0.007 in
Pinion Bearing Preload, New Bearings
1.7-3.4 N·m
15-30 lb in
Pinion Bearing Preload, Used Bearings
1.1-2.3 N·m
10-20 lb in
Pinion and Differential Case Bearing Preload, New Bearings
3.4-6.2 N·m
30-55 lb in
Pinion and Differential Case Bearing Preload, Used Bearings
2.8-5.1 N·m
25-45 lb in

May 17, 2009 | 2006 Chevrolet Colorado

1 Answer

I need the torque for rear pinion on f350


depends on rear axle you have
Dana 80 pinion nut torque is 470 ft lb pionion brg pre load is 25-45 in lb
Dana S110 pinion nut torque is 832 ft lb pinion brg pre load is 20-40 in lb
Dana S135 pioion nut is 800 ft lb and pinion brg pre load is 10-40 in lb

Mar 20, 2009 | 2004 Ford F350

1 Answer

Tork specks for the pinion nut on a 10 1/4 rear end from a 97 f250 hd


dd3e543.gif
the pinion nut does not have a specific torque there is a crush sleeve in there and preload needs to be set

Sep 24, 2008 | 1997 Ford F250 SuperCab

Not finding what you are looking for?
Cars & Trucks Logo

409 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...