Question about 2002 Ford E350

1 Answer

Looking for location of egr valve on 03' ford e350 5.4 ltr

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 375 Answers

On the side of the intake manifold

Posted on Jan 09, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the egr valve on a 99 Ford expedition


The EGR valve is in a very difficult spot to work on. If the EGR is bad it will set off the check engine light and make the vehicle run rough or stall at idle. It really doesn't make it run rough while driving or accelerating. What are the conditions when the car runs rough?

Mar 01, 2014 | 1999 Ford Expedition

1 Answer

Check engine light still on


You can have a look at the position of EGR valve and where it is located in following link:
6_17_2013_11_10_45_am.jpg

Jun 16, 2013 | 1999 Ford Explorer

1 Answer

Either code 4000 or 1400 on 2002 ford ranger 4.0 ltr v6. the right code should equate to the egr valve. I have replaced the egr valve but check engine light comes on again after reset showing same code.


code p1400 is a DPF EGR sensor CIRCUIT LOW VOLTAGE detected. most likely is a problem with the wiring to the egr or dpfe sensor. the pinpoint tests for code p1400 instruct you to test all wiring before replaceing the egr or dpfe sensor

Jan 19, 2011 | 2002 Ford Ranger Regular Cab

1 Answer

I need to know if my 2003 ford ranger 3.0 liter engine has a egr valve and where is it located


yes you have egr valve
its on the passenger side of the motor back at the fire wall
you can also locate it by looking at you exhaust
you will see a tube that goes from the exhaust up the fire wall and into the egr hope this helps
give feed back

Dec 28, 2010 | 2003 Ford Ranger Regular Cab

1 Answer

Where is the egr valve & position sensor located on a 1995 ford f-350 with a 460


The egr valve is located on the valve cover and has a 1/2 hose connected to it going to air cleaner.
The position sensor is located at the front bottom of motor it is looking at the harmonic balancer at the front bottom pulley under the fan blade pully.

Jul 12, 2010 | 1995 Ford F350

1 Answer

Check engine light is on. I was told it is the EGR. How do I locate the EGR on this vehicle? The code is P004. 2002 Chevy Express with 5.7 ltr. engine.


http://www.autoguide.net/apf/chevy-engine_parts/express_2500-2002-air_intake-b7010_148259del.html well it should be near the front of the intake manifold, you will see the EGR valve ( which looks like the thing on the web site link). Disconnect the electrical connector, remove the two 10 mm head bolts, remove the lead coated gasket from the intake. Be sure to clean the surface of all evidence of the gasket, using care to not get any into the intake. Place the new gasket on the EGR valve, using the bolts to keep it in place, put the new EGR on the intake. Tighten the bolts up evenly, plug the connector back in, hope this helps

Feb 09, 2010 | 2002 Chevrolet Express

2 Answers

Egr valve replacemebt


It's bolted onto the intake, next to the throttle body. If you look into the engine compartment and see the oil dipstick, look up and to the right. It will have a steel tube coming up to it from the exhaust. Why do you want to replace it? They rarely fail. EGR problems (codes) on Fords are usually caused by the Differential pressure feedback sensor.

Jan 24, 2010 | 2005 Ford Freestar

2 Answers

Need location of the erg sensor 2000 ford ranger


The egr valve has two sensors. One is an EGR position sensor which is physically attached to the EGR valve. The other sensor is the DPFE (Delta Pressure Feedback EGR) sensor, commonly called the EGR pressure sensor. It's location varies depending on the engine you have. You can fine this sensor by following the vacuum hose on the EGR valve. It will be with in inches of the EGR valve. The sensor will be black (plastic) or silver (metal), have two or three vacuum ports and an electrical connection on it.

The vacuum pressure sensor is a high failure item on fords. Any Ford parts department will have one in stock, as well as some aftermarket parts stores.

The new sensor may not look exactly the same as the old part, but will have all the hook ups as the old one. You may also need to replace the vacuum hose to the sensor as well

Feb 24, 2009 | 2000 Ford Ranger SuperCab

2 Answers

Location of the egr sensor on 2000 ford ranger


The EGR pressure sensor is located within inches of the EGR valve. The exact location varies depending on the engine (2.5L, 3.0L or 4.0L). It is usually attached to the upper intake manifold with two small bolts.

Feb 24, 2009 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
2002 Ford E350 Logo

Related Topics:

395 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...