Question about 2004 Chrysler Sebring

2 Answers

AC only works on high

The AC only works when it is set to 4 which is high. when it is on 3 it doesn't blow out anything. It is the same with just the blower and AC is off.

Posted by on

  • dan92752 Aug 01, 2008

    this problem seems to only involve the switch as it shows the same when on heat not air

  • charlenat Nov 25, 2008

    I had the same problem, but now the dial 4 doesn't work.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I had the same problem where the blower fan would only work on the "4" setting, not 1,2, or 3. The problem was the blower motor resistor block. I got the part from Oreily for about $30. To replace, start by removing the panel on the bottom of the passenger side dash. There was some kind of funky self tapping nut on a plastic post but it went on and off easy enough. Take the glove box out and locate the 2 wires coming off the blower motor. trace these back to the bundle going into the resistor block underneath. The wires (5 i think) go into a plug that plugs into the block. I unplugged the block after much frustration with the tiny plastic parts that latch the plug in (taking the block out at one point so I could see what I was dealing with but ended up putting it back in to get enough force on it to get it unplugged). Two screws hold the actual block in, unscrew these (i believe it was a 1/4 inch socket). If you bought the aftermarket part to save a buck like I did congratulations as you've just caused yourself more work. I used a file to expand the entryhole the block inserts into. Be careful not to file any plastic that may cause an air leak. the resistor block sits in the air duct to keep it cool while in use so don't leave it hang loose or you will have a potential fire hazard and an air leak reducing air flow while the fan is in use. Once you fit the new one in replace everything and you should be good to go. good luck, it took me 2 hours mostly trying to get the block unplugged. Still cheaper then the shop, which quoted me $300 for the repair.

Posted on Sep 02, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I recently by a 2004 sebring and the problem sometimes is the freon you have to check for leaks in the system... I need more details to give you my opinion.........

Posted on Aug 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

05 cobalt ac and heat wont blow air


you said your issue is the blower motor not working, the resistor likes to take a **** on these A LOT ($65). and if that doesn't fix it, it could be a issue with the heater control module. Ive had these issues with my 06 SS several times due to my stupidly high millage. Hopes this helps

Jun 05, 2012 | Cars & Trucks

1 Answer

The compressor is working but the ac is still blowing hot air what's the problem


even if the compressor is turning doesn't mean the compressor is good. You need to have someone put a set of gages on your system to see what the pressures are on the high side and the low side.This will give you an idea what your problem is.

May 29, 2012 | 2003 Toyota Corolla

1 Answer

Where is the AC overflow discharge valve in a 2001 hyundai sante fe v6? I overcharged my ac and it burst ac out for 4 seconds as I was charging then immediately stopped but it happened so fast that I...


There is a high pressure relief valve on the compressor to avoid over filling the system and locking up the compressor, or blowing a A/C hose, ect.,
You need a set of gauges to do it right (connected to high and low ports) then read this.
http://www.denlorstools.com/autoblog/2009/04/adding-freon-to-car-ac-gauge-readings-explained/

Aug 03, 2011 | 2001 Hyundai Santa Fe

1 Answer

Location of ac high pressure cutout switch on a 97 Plymouth voyager. Could it be a different problem? Had to replaced the PCM and a couple sensors because of a short in the wiring cluster. Now the ac...


HIGH PRESSURE CUTOFF SWITCH LOCATED ON AC COMPRESSOR DISCHARGE LINE LEADING TO THE CONDENSOR.THE HIGH PRESSURE CUTOFF SWITCH WILL CUT OFF THE AC COMPRESSOR IF SYSTEM PRESSURE RISES TO HIGH CAUSED BY RESTRICTION IN THE REFRIGERANT CIRCUIT OR OVERHEATED CONDENSOR.MAKE SURE COOLING FAN IS RUNNING WHEN THE AC SWITCH IS ON.THE COOLING FAN KEEP CONDENSOR COOL, IF COOLING FAN DONT RUN.YOUR AC WILL STOP BLOWING COLD AIR.HAVE THE REFRIGERANT SYSTEM CHECK OUT.MAKE SURE YOUR LOW SIDE PRESSURE IS 10 - 37 PSI. THE HIGH SIDE PRESSURE SHOULD BE 112 - 210 PSI. CHECK THE AC COMPRESSOR CLUTCH FUSE AND RELAY.

Jul 29, 2011 | Plymouth Voyager Cars & Trucks

1 Answer

Rear AC blows but front doesn't blow at all. It just all of a sudden quit working today. Also when the AC was working up front the car would act like it was going to stall out and has actually died on...


Sorry no quick fix here as this gas is highly toxic and poloutes the ozone layer so take vehicle to a specialist AC garage who can then vacate the system and then check the front ac unit expansion valve or the restrictor valve if you call it that

Jun 18, 2011 | 2004 Chevrolet TrailBlazer

1 Answer

2006 hyundai tucson ac barely blows it is really cold, but doesn't blow hardly at all


The electric motor is probably shot. Does it work when you switch between settings like vent and floor? If one setting works and another doesn't then you have a problem with the dampers in the dash and the dash needs to be removed. If the motor is shot, you can find is location by listening very carefully for any noises when you turn on the ac coming from near the dash board. You can also ask a local auto parts rep to locate it for you, they can also sell you a replacement if you need it.

Jun 08, 2011 | 2006 Hyundai Tucson

2 Answers

Air conditioner blows hot air inadvertantly.


possibl ac compressor clutch problem,cooling fan at rad not working so ac goes into high press mode and turns off(so it doesn,t blow system apart,built in safety)not enough r134 in system(low charge)

Sep 19, 2009 | 1997 Chrysler Concorde

1 Answer

The AC blows on #4 fan setting but doesn't blow at all on 1-3


That is the blower resistor. 4 is wide open, so, no resistance. I had 4 of them put into my truck. The wires were burnt and shorted the others until the problem was found. Check the plug if you do this yourself.

Jun 13, 2009 | 2005 Chevrolet Colorado

2 Answers

Interior fan only working on high #4


it only takes a sprk to blow the heat and ac switch out such as installing a stero ormayby rounding the plastic off behind the switch

Jan 12, 2009 | 1999 Mercury Cougar

1 Answer

AC not working


Is the system set to the recirculate position? If so, check the inlet under the dash, by the passengers feet, for anything blocking the pickup.This can cut the output in half.

Aug 06, 2008 | 1999 Buick Century

Not finding what you are looking for?
2004 Chrysler Sebring Logo

331 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...