Question about Oldsmobile Bravada
Its the round black can located in the bottom passenger side front corner. has two to three hoses plugged into the top of it.
Posted on Jan 02, 2011
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Jun 25, 2017 | Cadillac Cars & Trucks
Jul 26, 2016 | GMC Sierra Cars & Trucks
May 27, 2016 | 2004 Chrysler Sebring
Feb 08, 2016 | Cars & Trucks
P0443 The fuel vapor canister reduces that gas smell on hot days outside/inside of car. The fuel vapor canister fillers bad smells from gas tank on hot days when the gas expands and burps fumes through carbon canister filter. From the canister (gas vapor fumes) goes back into the engine to be burned again...it's a closed loop for vapors to be recycled though engine. Don't worry, once the carbon canister dries out and no longer flooded with raw fuel the code should go away...just don't let the top off fuel tank back flow into the 'Evap emission control' carbon filter near the top and close to the gas cap...:)
Apr 20, 2014 | 2000 Ford Mustang
Feb 11, 2014 | Nissan Frontier Cars & Trucks
May 04, 2011 | 1997 Ford Escort
Mar 25, 2011 | Ford Aerostar Cars & Trucks
OPERATION Changes in atmospheric temperature cause fuel tanks to breathe, that is, the air within the tank expands and contracts with outside temperature changes. If an unsealed system was used, when the temperature rises, air would escape through the tank vent tube or the vent in the tank cap. The air which escapes contains gasoline vapors.
The Evaporative Emission Control System provides a sealed fuel system with the capability to store and condense fuel vapors. When the fuel evaporates in the fuel tank, the vapor passes through the EVAP emission valve, through vent hoses or tubes to a carbon filled evaporative canister. When the engine is operating the vapors are drawn into the intake manifold and burned during combustion..
A sealed, maintenance free evaporative canister is used. The canister is filled with granules of an activated carbon mixture. Fuel vapors entering the canister are absorbed by the charcoal granules. A vent cap is located on the top of the canister to provide fresh air to the canister when it is being purged. The vent cap opens to provide fresh air into the canister, which circulates through the charcoal, releasing trapped vapors and carrying them to the engine to be burned.
Fuel tank pressure vents fuel vapors into the canister. They are held in the canister until they can be drawn into the intake manifold. The canister purge valve allows the canister to be purged at a pre-determined time and engine operating conditions.
Vacuum to the canister is controlled by the canister purge valve. The valve is operated by the PCM. The PCM regulates the valve by switching the ground circuit on and off based on engine operating conditions. When energized, the valve prevents vacuum from reaching the canister. When not energized the valve allows vacuum to purge the vapors from the canister.
During warm up and for a specified time after hot starts, the PCM energizes (grounds) the valve preventing vacuum from reaching the canister. When the engine temperature reaches the operating level of about 120°F (49°C), the PCM removes the ground from the valve allowing vacuum to flow through the canister and purges vapors through the throttle body. During certain idle conditions, the purge valve may be grounded to control fuel mixture calibrations.
The fuel tank is sealed with a pressure-vacuum relief filler cap. The relief valve in the cap is a safety feature, preventing excessive pressure or vacuum in the fuel tank. If the cap is malfunctioning, and needs to be replaced, ensure that the replacement is the identical cap to ensure correct system operation.
OBD-II EVAP System Monitor
Some of the models covered in this guide have added system components due to the EVAP system monitor incorporated in the OBD-II engine control system. A pressure sensor is mounted on the fuel tank which measures pressure inside the tank, and a purge flow sensor measures the flow of the gases from the canister into the engine. The purge valve is now called the Vapor Management Valve (VMV). It performs the same functions as the purge valve, however it looks slightly different. A canister vent solenoid is mounted on the canister, taking the place of the vent cap, providing a source of fresh air to the canister.
The PCM can store trouble codes for EVAP system performance, a list of the codes is provided later in this information. Normal testing procedure can be used, see EVAP System Component Testing in this Section.
Oct 04, 2010 | 1997 Ford F150 Regular Cab
Jul 19, 2010 | 1996 Ford Explorer
101 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: