Question about Nissan Frontier

2 Answers

Hello. I have a jeep wrangler with a nissan td27 turbo engine adaptation. After the job was done it ran great for about 1500 miles and one day goin up hill it felt like it was running out of diesel but having a full tank of gas, it failed till it shut off by lack of diesel. After that I changed filters and serviced the diesel pump and cleared the fuel lines. It works great and gets about 28mpg. but very often goin up hill again still does it. I have to get out and pump the filter to fill it up again and usually that solves it. Some times I have to do it more than once in the same hill. I you can help me i will really appreciate it. Jc. from Guatemala, Central America

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Nissan Expert
  • 279 Answers

Check the pickup in the fuel tank. Depending on what that pick up is, and howitzer is shaped, the angle caused by going uphill may be such that the pickup is sucking onto the floor of the tank, blocking the flow of fuel. The alternate is that the pickup is actually exposed to air when the fuel angles away from it going uphill, or the flexing of the pickup creates an air leak in the pickup. If none of this applies, then I support the previous answer;fitting an inline electric fuel pump , a low pressure one should keep the injection pump supplied with the right amount of fuel at all times.

Posted on Feb 02, 2015

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,400 Answers

You might consider adding a low pressure electric pump to keep diesel flowing and pressure in the lines

Posted on Jan 02, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a nissan diesel 4 cylinder td27 engine , what i the normal oil pressure gauge reading for this engine whilst running


2.9 to 3.9 bar at 3000 rpm is fairly general for the Nissan range including turbo diesel, though the pressure isn't listed for the td27 engine. I doubt it would be more or less than the others.
I notice one Nissan commercial vehicle engine where 3.0 bar at 2000 rpm is specified.

The oil pressure test should be carried out at normal operating temperature.

Feb 26, 2015 | Nissan Cars & Trucks

1 Answer

How do i connect a wrangler speedometer to a turbo 350 transmission


Your factory tach won't be accurate because a 350 is an 8 cylinder engine. I put a 350 into a Vega, and my speedo was slightly off because of the differences between the ratios as well. I recommend looking for an aftermarket adapter, or a kit if you can't get the cable to connect into the tranny.

May 06, 2014 | 1990 Jeep Wrangler

1 Answer

Navara forum


yes this is possible to do but you need the proper computers and wireharness from the doner vehicle. it is a matter of swaping parts good luck

Dec 02, 2013 | Cars & Trucks

2 Answers

Nissan engine td27 valve clearns


I need the wiring digram for the TD27 turbo Diesel Engine I'm changing from YD25 to TD27 turbo

Aug 15, 2010 | Nissan Hardbody Cars & Trucks

1 Answer

Theres a slight tap/rattling noise on my subaru impreza 2 litre turbo it started when i changed the 2 head gaskets due to water in the oil.any help would be great


does it sound from the top of the engine like teppets or the bootom of engine ? sometimes after you have a job like that done it takes sometimr for the tappets to fill up with oil .Have you ran it and for how long if you havent ran it for atleast 5 mile try running it in to fill the tappets up . please tex me if you need more help.

Oct 28, 2009 | 1999 Subaru Impreza

1 Answer

Transmisson on my jeep knocks


Sounds like you may have a bad cluster gear in the tranny. You can get a brand new tranny for a decent price through Quadratech. Be wary of the rebuilt tranny. If not done correctly you will have more problems again.

Feb 26, 2009 | 1992 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...