Question about 1998 Mercury Villager

1 Answer

1998 Mercury Villager --- Had to change the front motor mount and lift the engine some to do it. Everything went fine, but now we do not have heat. I could not see any lines loose or crimped, but I am a novice. Could anyone give me any leads on where to look and what to look for? Thank you! Steven

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Did you drain coolant? If yes, you have trapped air.

Also, check the cable or wiring going to hot water valve on passenger side in one of the 2 heater hoses going into cowl.

go here, read files, see photos

http://groups.yahoo.com/group/villagerquest/

Posted on Jan 08, 2011

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

localwonder
  • 6784 Answers

SOURCE: where is a knock sensor for 1998 Mercury Villager located?

  • The sensor is mounted in a fixed position in the engine block. The tip of the sensor protrudes into the crankcase at a distance of 0.05 plus or minus 0.02 inch from the crankshaft.
  • A crankshaft adjusting tool may be used to check these rings.
    • Place the tool on the pulley extension surface and rotate the tool around the pulley.
    • If any blade touches the tool, replace the pulley.
  • Inspect the trigger wheel behind the crankshaft pulley and the sensor for damage.
  • If the engine misfires all the time or on acceleration only, test the following components:
    • Engine compression.
    • Spark plugs.
    • Spark plug wires.
    • Ignition coils test for firing voltage with a test spark plug.
    • Crankshaft sensor.
    • Fuel injectors on multiport and sequential fuel injection systems.

Posted on May 18, 2009

  • 4 Answers

SOURCE: car stalls while moving, then after 2-5 minutes starts back up

disconnect the fuel filter at both ends to see if the filter is clogged. If you are not getting any fuel on either end then you should get a new fuel pump.

Posted on May 25, 2009

jagjeffery
  • 316 Answers

SOURCE: what it means p1166 and p1167 on a mercury villager 99

p1166 and p1167 are Air/Fuel ratio code sensor codes (O2 sensor codes) heater circuit problem

Posted on Jun 02, 2009

Molson02536
  • 3854 Answers

SOURCE: Code reader knock sensor where is it located

According to the Haynes manual it is under the intake manifold, Upper and lower intake manifolds must be removed for access. If you go to Auto Zone, they have the sensor and can give you the step by step instructions to replacing the knock sensor with common tools. Good luck and hope this help.

Posted on Sep 02, 2009

MNfisherman
  • 11896 Answers

SOURCE: need a daigram of the timing belt 1998 mercury

You can go to autozone.com and register for FULL FREE online repair manual with everything you could need.
Or you can go to google ebooks and view a chilton's repair manual for your car.

Posted on Oct 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 mercury villager van, passenger auto seat belt motor running continuously & seat belt won't work. Drained battery. Where is the fuse located?


Engine compartment main fuse panel 30 AMP fuse Fuse #4 scroll down and look at this diagram picture on this link. http://www.autogenius.info/mercury-villager-1st-generation-1993-1998-fuse-box-diagram/ caution, this fuse runs power seats, windows and sun roof as well.

Mercury Villager 1st Generation 1993 1998 fuse box diagram Auto Genius

Oct 15, 2016 | 1994 Mercury Villager

1 Answer

Where is the freeze plug on a 1996 mercury villager


Freeze plugs run along the side of the engine block. There are some also between the rear of the engine and where the transmission mounts that you can't see when there connected. Some can be difficult to change depending on which ones are leaking. Sometimes accessories or motor mounts have to be removed to gain access, again depending on which one is leaking.

Jun 06, 2015 | 1996 Mercury Villager

1 Answer

Need xplodd view of motor mounts , transmission mount , brackets on a 1996 mercury villager van


On a lift is the easiest way because you will need to raise and support the engine while the motor mount is replaced. Once you have a new mount, I would replace both while you are at it, the procedure will become self evident. Not a difficult job.

Actually this can be done at home in your driveway in a couple hours max. Raise the vehicle on jack stands and be sure to set the parking break and block the rear tires. Then use a block of wood and a floor jack under the pulley to raise the motor just enough to take the weight off the mounts. Both the front and rear mounts are attached to the same cross member and you will need to do 50% of the job of taking out the front mount to get the rear mount out and visa versa so it is worth it to replace both if you are going to do one. Remember not to tighten them down more than snug until after the weight of the motor is back on the mounts. There are torque specifications in the front of your repair manual. Of course if you have a lift great, but for most of us do not think that you cannot do this simply because you don't have a lift.


Increase Engine Horsepower.

Jun 02, 2012 | Cars & Trucks

2 Answers

Need to replace motor mounts on my 2000 mercury villager sport and need a diagram or instructions to do this


yahoo group for villager quest owners has files on this and part numbers. front ones break.

Sep 12, 2011 | 2000 Mercury Villager

1 Answer

Where is the fuel filter?


1998 Mercury Truck Villager Van 3.0L SFI SOHC 6cyl The Fuel Filter is located: Under hood, driver side, rear engine area, driver side of master cylinder, mounted in fuel line .

Hope helps (remember rated this).

Jun 15, 2010 | 1998 Mercury Villager

1 Answer

Just aquired A Ford Mercury Villager 1998 any suggestions as to stores for spares ie servicing Brake Pads, etc


On the villagers the front motor mount alot of the time is bad on these vehicles.Change the oil every 3,000 miles.Also check the air cleaner and the battery terminals and make sure they are clean if not clean them with like some 100 -150 grit sandpaper on the battery cables the positive and negative wires and also clean the battery post where the cables hook up to.

Apr 01, 2010 | 2000 Mercury Villager

1 Answer

Engine motor mounts are broken.


besure when you replace engine mount.you have to use a engine lift to take weight off the mount.you need a haynes manual.it will show you where engine mounts located.

May 29, 2009 | 1999 Mercury Villager

1 Answer

How can i replace it?


http://autos.groups.yahoo.com/group/villagerquest/

it's usually called the trans mount cause that's what's on that side.

Section 02-03: Engine and Transaxle Mounting 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Support Insulator, Front Transaxle Removal
  1. Remove the battery (10655). Refer to Section 14-01 for the removal procedure.
  2. Remove the Engine Air Cleaner (ACL) (9600). Refer to Section 03-12 for the removal procedure.
  3. Remove the radiator coolant recovery reservoir (8A080). Refer to Section 03-03 for the removal procedure.
  4. Remove the battery tray (10732). Refer to Section 14-01 for the removal procedure.
  5. Support the transaxle with a floor jack.
  6. Remove the front transaxle support insulator through bolt and nut.
  7. Remove the three front transaxle support insulator bolts and the front transaxle support insulator.
-----------------------------------------------------------
Support Insulator, Rear Transaxle Removal
  1. Remove the rear transaxle support bracket. Refer to the procedure in this section.
  1. Raise and support the vehicle.
  1. Remove the three rear transaxle support insulator nuts.




  1. Lower the vehicle.
  1. Remove the rear transaxle support insulator from the vehicle.

Mar 29, 2009 | 1997 Mercury Villager

Not finding what you are looking for?
1998 Mercury Villager Logo

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

fordexpert

Level 3 Expert

5471 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...