Question about 2005 Kia Sedona

Open Question

Po337 code ckp sensor replacement - 2005 Kia Sedona

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 odyssey CKP problem code P0335. I replace the crank seal and this code show up after that. then I open again to replace the sensor and code still there. What I can do? thanks


code p 0335 refers to crankshaft position sensor (CKP)---circuit malfunction===causes ---wiring---CKP sensor ---ECM
the wires are a good place to start and check for damaged insulation , broken wires or bad harness connections
next there is an air gap setting between the sensor and the exciter (segmented bars on a ring) on the crankshaft check that is correct ---dimension available from the workshop manual

Oct 06, 2016 | 2000 Honda Odyssey

1 Answer

CAR WAS NOT STARTING ALL THE TIME-CODE PO337. REPLACED CPS, CLEARED CODES, CAR DOES NOT START AT ALL. HELP


code p 0337 refers to crankshaft position(CKP) sensor ---low input====causes ---wiring short to ground--CKP sensor ---ECM
did you replace the correct sensor as it is the crank shaft sensor and not the cam shaft position sensor which would be a code p 0340 on wards

Dec 01, 2015 | 2003 Saab 9-3 Linear

1 Answer

P1336 gm code


P1335 CHEVROLET P1335 CHEVROLET - Crankshaft Position Circuit Possible causes
- Faulty Crankshaft Position Sensor
- Crankshaft Position (CKP) Sensor harness is open or shorted
- Crankshaft Position (CKP) Sensor circuit poor electrical connection help.png Help with this
Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power
- Engine Stall
P1335 CHEVROLET Description
The Crankshaft Position (CKP) sensor sends pulses to the Powertrain Control Module (PCM) as the reluctor wheel teeth rotate past the CKP sensor. The PCM uses the CKP pulses to synchronize the ignition and fuel injector operation, and to time the interval between each CKP pulse. The PCM determines when an excessive change in crankshaft speed occurs by comparing each new time interval with the previous interval. A misfire causes an unexpected change in the crankshaft speed. A certain amount of acceleration/deceleration is expected between each firing stroke, but if the crankshaft speed changes more than an expected amount, the PCM interprets this as a misfire. The interval between CKP sensor pulses is extremely small. At high engine speeds, slight variations in the following components make misfire detection difficult:
- Crankshaft
- Reluctor wheel
- CKP sensor
The PCM learns variations during the Crankshaft Position System Variation Learning Procedure. The PCM compensates for these variations when performing detect misfire calculations. Only a scan tool can command the PCM to perform the Crankshaft Position System Variation Learning Procedure again.
Perform the learning procedure after the following actions:
- A PCM replacement
- Any operation or repair involving the crankshaft, the CKP sensor, or the CKP sensor to reluctor wheel gap relationship.
- An engine replacement.
- The ignition switch is in the ON position until the battery is drained.


Read more: http://nissanhelp.com/diy/obd_codes/p1335_chevrolet.html#ixzz37IoD1Imx

Jul 12, 2014 | 2001 GMC Safari

1 Answer

I replaced the engine control module


code po335 refers to crankshaft position sensor(CKP)--circuit malfunction===causes wiring--CKP sensor --ECM
check the air gap and rotor security . Check for dirt in the air gap. Change CKP sensor.
code po113 refers to intake air temperature (IAT) sensor ---circuit malfunction===causes ---wiring open circuit /short circuit to positive ---wiring short to ground---ground wire defective--IAT sensor ---ECM

Mar 25, 2014 | Hummer Cars & Trucks

1 Answer

Kia Amanti Ignition failure sensor


Code p0320 refers to crank shaft position (CKP) sensor/engine speed RPM sensor-circuit malfunction===causes---wiring CKP/RPM sensor ---ECM. Get your hands on an aftermarket workshop manual for the car and you should be able to replace the items

Dec 27, 2013 | Kia Amanti Cars & Trucks

1 Answer

Car wont start when hot


do not use an aftermarket sensor, get one from your dealer

Jun 15, 2012 | 2004 Saab 9-3

1 Answer

Code P1391, replaced camshaft and crankshaft sensors, plugs and wires, rotor, and a couple fuses, can a loose or bad distributor be the cause for this code?


DIAGNOSTIC TROUBLE CODE (DTC) P1391: "INTERMITTENT LOSS OF CMP OR CKP"
This DTC is monitored with the engine cranking or running. This DTC will be stored in the Powertrain Control Module (PCM) when the PCM FAILURE COUNTER reaches 96 failures for 2 consecutive trips.
Posiible causes are: Craknkshaft Position (CKP) sensor improperly installed, defective CKP sensor, defective distributor, defective Camshaft Position (CMP) sensor, defective PCM, defective or broken flywheel, defective connectors or defective wiring.
Proper diagnosis is recommended before replacing ANY parts.

Oct 21, 2011 | 1999 Dodge Dakota

2 Answers

Have a 2004 kia sedona have replaced the crank position sensor but still shuts off and gives p 0335 code


WHAT CKP SENSOR DID YOU REPLACE I BELIEVE THE SEDONA 3.5L ENGINES HAS 2 CKP SENSORS.YOU HAVE ONE CKP SENSOR LOCATED FRONT OF ENGINE ON THE OIL PAN MOUNTED BEHIND CRANKSHAFT PULLEY AND THE OTHER CKP SENSOR LOCATED NEAR THE TRANSMISSION BELLHOUSING. CHECK TO SEE IF YOU HAVE CKP SENSORS. IF NOT CKP SENSOR WIRE COULD BE DAMAGED.ALSO CHECK TO MAKE SURE BATTERY POWER GOING TO CKP SENSOR B PLUS WIRE IF NOT CHECK THE ECCS RELAY OR FUSES MAKE SURE POWER IS GOING TO CKP POSITION SENSOR

Oct 10, 2011 | 2004 Kia Sedona

2 Answers

2005 nissan almera,1.5letre.. fault code po725


P0725 NISSAN - Engine Speed Signal

The P0725 Codes is triggered when TCM does not receive the engine speed signal from ECM.

The Engine Control Module (ECM) monitors the engine speed through the Crankshaft Position (CKP) sensor with the engine running, and send signal to the Transmission Control Module (TCM).

Symptoms:
- Engine Light ON (or Service Engine Soon Warning Light)

Possible causes:
- Open or shorted CKP sensor circuit condition
- Poor CKP sensor electrical connection
- Check communication error between the ECM and TCM
- Failed CKP Sensor

Possible solution:
Very common problem with Nissan vehicles, usually replacing the Crankshaft Position sensor takes care of the problem.

Keep us updated.

Feb 12, 2011 | 2005 Nissan Altima

1 Answer

What are error codes P0372, and P0335


Hi, these codes relate to the crankshaft position sensor. Recommend you check the sensor to make sure it is tight and the connector is fully on. If it looks in order, consider replacing the sensor. If you reply with your model and year, I will see if I can provide additional information.

P0335 Crankshaft position (CKP) sensor - circuit malfunction
Possible causes: Wiring, CKP sensor, ECM

P0372 Timing reference, high resolution signal A - too few pulses
Possible causes: Wiring, CKP/RPM/CMP sensor, ECM

Jan 02, 2011 | Hyundai Sonata Cars & Trucks

Not finding what you are looking for?
2005 Kia Sedona Logo

Related Topics:

478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...