Question about 2005 Dodge Neon

1 Answer

How do I replace the tensioner pulley on a 2005 Dodge Neon?

Posted by on

  • wyman
    wyman Oct 18, 2013

    how much help is this? take it off put other one on? duh?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

You have to remove the whole bracket that the tensioner assembly is attached to then you can get at the bolts that holed the tensioner and pulley together to service. Have fun.

Posted on Jan 06, 2011

  • wyman
    wyman Oct 18, 2013

    useless imformation

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power steering pulley or tensioner pulley?


Take the tension off the belt and then move each pulley by hand . If the tensioner pulley feels rough or makes a noise, replace it. Same goes for the power steering, although the pump may be noisy without the pulley feeling loose.

Nov 17, 2014 | 2005 Dodge Neon SXT

1 Answer

Serpentine belt routing diagram for 2004 dodge neon


over p/s pulley,down to a/c pulley ,up to crankshaft pulley ,under tensioner pulley

Dec 05, 2012 | 2004 Dodge Neon

1 Answer

How do u remove a tension pulley on a 2005 dodge neon


remove the belt, then remove the pulley, you may need a tensioner bar or sometimes a 3/8 ratchet will fit. when you instal the new one there may be a keyway or alignment dowel, besure it slides into place before tightening it down

Feb 11, 2012 | 2002 Dodge Neon

1 Answer

2005 dodge neon the idler pulley went out. How do I change wthe idler pulley?


You will have to go to the tensioner pulley and put a wrench on that bolt and apply presure in the allowed direction and take the belt off...look first to see if there is a diagram of how the belt goes back on if there isn't write one down before you take the belt off...might be a good time to inspect the belt for cracks and replace as needed.

Mar 26, 2011 | 2005 Dodge Neon

1 Answer

What is the best way to replace the tensioner pulley on a 2005 neon? i have the tool to remove the power stearing pully. is there also a tool for the tensioner pully? will i have to pull the motor?


No you will not have to pull the motor. The pulley is held on with a standard bolt. However, if the pulley bearing is worn, I would suggest replacing the entire tensioner. The spring inside gets weak over time. It won't cost all that much more for the whole tensioner (it includes a new pulley already installed) and it will prevent a problem in the future.

Mar 12, 2011 | 2005 Dodge Neon

1 Answer

Replace a tensioner pulley on a 2005 dodge neon


ok shade tree, here, remove power steering unit, motor mount, on pass side , take bolt out that goes to motor- thru fron the inner fender its behind plastic plug jack motor as high as possible and get to bolts out that are on plate the tensioner is monted to then drop motor as low as possible and remove last bolt to tenioner plate, wrestle the plate out in order to change tentioner its a real fight , but nessacary.

Dec 28, 2010 | 2005 Dodge Neon

1 Answer

How do you replace serpetine belt on a 2001 Dodge Neon


You need to locate the tensioner pulley.Need to pull tensioner forward.There will be some resistance.If you can get that forward the belt will come right off. Just remember the belt route when you do it.

Mar 14, 2010 | 2001 Dodge Neon

1 Answer

How to tighten altenator belt on a 95 dodge neon . I see no way of getting my hands in there to do it.


You cannot tighten the belt. It is the Tension arm/pulley's job to do so. If the belt is loose, then it either means the belt needs to be replaced, its the wrong belt, its routed wrong, or the tension pulley/arm is bad.

Nov 15, 2009 | 1995 Dodge Neon

1 Answer

Removal of tensioner pulley in a 2003 Dodge Neon


the tensioner is part of the engine mount bracket..not serviced seperately as far as i know

Mar 16, 2009 | 2000 Dodge Neon

2 Answers

How to replace belt tension pulley for dodge neon 2002


The power steering and A/C belt is tensioned by a tensioner pulley. Mine went bad and was "screaming" I thought it was the power steering pump and I replaced it only to find that it wasn't the problem. I couldn't find any bolts and deemed it too much of a problem for me to replace at home. The shop had to drop the engine and transaxle assembly from the engine bay in order to get enough room to replace the pulley. The problem with many FWD cars is having enough room to work so if you have to replace it, the engine has to move because you only have about two inches of room otherwise.

Jun 21, 2008 | 2002 Dodge Neon

Not finding what you are looking for?
2005 Dodge Neon Logo

740 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...