Question about 1994 Dodge Ram

1 Answer

How to aligned hung doors - 1994 Dodge Ram

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 45 Answers

THE ONLY ALIGNMENT YOU HAVE IF THE HINGES ARE WELDED TO BODY POST ARE NEW DOOR PINS AND BUSHINGS. YOU CAN GET THEM AT ANY PARTS STORE.

Posted on Jan 02, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove l slide door inside panel


Inner Door Panel Removal - YouTube

? 3:53
https://www.youtube.com/watch?v=tF5vCjhcyd8
Jan 23, 2008 - Uploaded by richpin06a
Saturn S-series Inner Door Panel Removal. ... Power Window Repair, Window Slider Replacement: Second Generation Saturn S Series. ... Beginners How to for Installing Interior Pre-Hung Doors- Duration: 4:59. ... How To Install Replace Door Panel Jeep Grand Cherokee 99-04 1AAuto.com - Duration: ...

Oct 27, 2015 | 2002 Jeep Grand Cherokee

1 Answer

Alignment door


check the door restrictor band in the front section of the door as it probably has pulled the panel out of alignment or broken a section out (near the hinges). Re-align the door by adjusting the hinges on the body panel.

Mar 02, 2014 | Cars & Trucks

1 Answer

I have a 2003 jag x type and the door indicater is on is that bad?


Lubricate the door latches, the sensors for 'door ajar' are located there and can get hung up-after spraying, allow it to sit for a couple of minutes, then open and close the door 6 to 12 times (each door) to free the sticking mechanism.

May 24, 2011 | 2003 Jaguar X-Type

1 Answer

I just replaced the inner an outer tierod ends.the steering wont turn back after u make a turn


You need a frontend alignment. If you took off the entire tierod you may have hung the rod backwards and it is catching. When you unscrew the ends you are suppose to count the twists and then replace the ends with the same amount of twists.

If the rod is too long or too short now it will put the tires in a position that is not aligned. You can align this temporarily by straightening the wheel so the tires are parallel. Then measure the inside of the rim so that the BACK of the rims are about 3/8 of a inch wider than the BACK of the rims in the front of the tire. The tires are suppose to travel knob kneed about 3/8" toe-in.

Apr 15, 2010 | 1999 Ford Taurus

1 Answer

99 bonneville I have a ticking noise comming from under the dash . The temp will not change


You have a temp door actuator motor gone bad,or the door itself is hung up,the dash will have to be removed to repair the problem.

Mar 13, 2010 | 1999 Pontiac Bonneville

1 Answer

Window on driver side of 2003 Camry stuck. Had


You can adjust the door latch by aligning the male and female portion of each. This can be adjusted by loosening the screw and aligning it. And finally when aligned, tighten the screw. Unless otherwise if the door hinges are loose, such that the doors are misaligned, then, you have to replace the door hinges. Or put a bushing at the door hinges to keep it
aligned. This will correct the defect.

Nov 15, 2009 | 1992 Toyota Camry V6

1 Answer

How to change the tail light the plastic case wont come out


From inside the bed, remove the bolts behind the tail light. The light should pull out. It may need the encouragement of a stronger pull, as there are plastic alignment studs that slide into holes in the sheet metal that sometimes get hung.

A little extra pull after you are sure all of the bolts are out will do the trick.

Oct 27, 2009 | 2001 Ford F350 Super Duty SuperCab

1 Answer

How to adjust rear door on o2 ranger supercab


loosen the bolts and insert a body shim, that a local body shop can in most cause give you, behind each bolt and tighten that will kick the door edge away from the body.

Jun 22, 2009 | 1995 Ford Ranger Supercab

1 Answer

Elrctric side door won'topen


If you want to pay for the Premium answer to this question, just let me know.

Nov 28, 2008 | 2003 Dodge Caravan

Not finding what you are looking for?
1994 Dodge Ram Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...