Question about 2003 Hummer H2

1 Answer

Head lights pointing down need to adjust any help

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Hummer Master
  • 5,763 Answers

Theres an adjustment screw for up and down and also a screw for left and right, you can go to a parking lot and ajust them your self you will aim the light to the specs you like but careful not to aim to high as you will be blinding oncoming drivers, you can always readjust them until you can it right, open the hood during the day to locate the adjustment screws.

Posted on Jan 02, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I can adjust the low beam on my 2010 Impala but I can't adjust the high beam

low beam and high beam is in the one setting unless you have separate headlights
procedure is to place the car on level ground 3 feet from a wall that reflects the head light
draw a cross on the wall at the height of the center of head light lens
switch on the head lights (high beam)and you will see the center beam of high beam on the wall
using the screws at the back of the assembly adjust that spot to be pointing slightly to the left if rh drive ot left if lh drive and about 1 inch below the line that you drew on the wall
when you have that correct , it will put the low beam in the correct legal position
if the rear of the vehicle is sitting down , trailer of caravan on , the the head lights have to still be adjusted to legal setting

Oct 20, 2015 | Cars & Trucks

1 Answer

How do i adjust headlights

There should be a little screw to turn to adjust the head light. This will be in the head light assembly itself on top. If you have a manual they tell you in that also - but you should be able to find it any way. Some cars use a screw driver and some use a special type of screw driver you may have to buy.

Apr 13, 2015 | Cars & Trucks

1 Answer

High beam in 2007 Impala pointing down after changing bulb.

Check for proper installation if you you install it properly you should have adjust the head light again by two nut behind the head light one for vertical another for horizontal

Dec 04, 2013 | 2007 Chevrolet Impala

1 Answer

Headlights point to high

There are adjusting knobs beside the head lights housing 3 normally and by adjusting each at a time the head light can be aimed down left and right.. Correct adjustment will be when the center of the beam is at the same height as the center of the head light at a distance of 3 ft in from of the car on level ground. Check that the rear of the car is at correct ride height as sagged suspension will cause this problem. Consider if you have a caravan hooked up then the headlights will point up. . Same problem.

Apr 04, 2013 | 2009 Lexus GS 350

1 Answer

Head light adjustment for a pt cruiser drivers side replace lamps low on drivers side when driving points down

there should be an adjustment screw or torx head bolt that will turn and raise the light

Mar 26, 2011 | Chrysler PT Cruiser Cars & Trucks

1 Answer

My passenger side head light needs to be adjusted it is pointing almost strait down

Just take your Audi to a State Inspection Station. It's a Slam Dunk for them. And it will be in accordance with the Law.

Best Regards

Oct 10, 2010 | 2006 Audi A4

1 Answer

I just got a blazer i think i need the headlight to be alignment but dont know the accurate pointing to the sky while i need it to point to the road please help me i work over night and it always a...

there is a hex head screw on the top of the head light under the hood that adjust the head lights, the best way i have found to get a good adjustment is to make sure the truck is level and in front of like a garage door and stay back a 20 or 30 feet and adjust them like you are going down the road.

Feb 25, 2010 | 1997 Chevrolet Blazer

1 Answer

My GMC truck 1993 Sierra just had new headlights installed. But the high beams point into the trees. It seems both the high and low beam lights are in one enclosure. Can I adjust these down?

Yes you can. There is an adjustment screw at the top of each head lamp and you just turn them out or counter clockwise and the beam will come down. You may also have to adjust them side to side also. There is an adjustment screw as well.

Aug 27, 2009 | 1993 GMC Sierra K1500

1 Answer

How to set auto headlights

Ford Requires a special tool to adjust headlights, you can buy from ford or Mac or snap-on tools. Car must be level and you need it to be slightly dark outside so you can see what your doing. Adjust driver head light on low beam, as you are turning adjustment screw turn the screw for raising the head light and raise the head light up or down till it is 30 feet in front of you. you can take steps and measure it this way which would be 10 steps or ten yards on a normal person that is 5.8ins tall. then adjust the side adjuster so that when looking at the head light spot on the ground it is pointing to the passenger car side about one foot away from straight on. Meaning if you were going down the highway that the light would point down and slightly to the right not on the center road painted lines. Next adjust the passenger side to where it is the same height as the driver side, then hit your high beams. it should be aimed so that the lights do not shine into on com-ming drivers eyes. If you have a garage or a building that you can get thirty feet away and the car is level it will make it easier for you to see what your adjusting. Afterwords you may have to make a minor adjustment to both lights. I like to set them so that the passenger is slightly higher and a little to the right so you can see going down the road at night an avoid or see a deer or person to the right side of the road. Some states requires that a certified light mechanic to do this so be sure you are not voilating any laws when doing this. Thanks for using fix-ya and rate if this was helpful.

Aug 25, 2009 | 2003 Ford Expedition

1 Answer

Adjust my head lights

depends on the car usually you can adjust them using a phillips screw driver and wind up or down look for long screw aronud top and bottom of light however saying this it depends on the car

Apr 15, 2009 | 2007 Chevrolet Aveo Sedan

Not finding what you are looking for?
2003 Hummer H2 Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hummer Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Hummer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides