Question about 2003 Chevrolet Tahoe

1 Answer

I hear a clunk when puting the truck in reverse I put it on lift an the drive shaff has no play could it be in the power take off the truck is kept in a garage and theres no signs of any leaks any where

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Could be play in the bearing on the reverse gear in the transmision box, (gearbox)

Posted on Jan 02, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 2001 malibu clunk when shift into reverse or drive


check ur cv axles one may be going bad also check steering and suspension system--struts worn, loose --ball joints goin --even tie rods can cause play

May 23, 2014 | 2001 Chevrolet Malibu

1 Answer

My motor is slamming when put in reverse


Check u-joints and cv-joints. When they wear out it can cause play in the drivetrain, causing a 'clunk' when you put the car in reverse (and usually from reverse to drive). But, it sounds likely that this is what's causing your problem.

May 01, 2011 | 2002 Saturn Sl

3 Answers

Fiesta started making noises either gearbox or clutch? clunks going in to reverse, shudders driving off in 1st gear


sounds like your clutch is going out, is it hard to put in gear with clutch all the way depressed? could also be the sinkronyzer going out, could be the gears in the transmission also going bad. need to check the fluid in the transmission.

Feb 11, 2011 | Ford Fiesta Cars & Trucks

1 Answer

My 1989 toyota 4-runner 4-wheel drive not working.


SOUNDS LIKE AXLE WINDING UP. ARE YOUR TYRES ALL THE SAME SIZE AND ARE YOUR HUBS FREEING PROPERLY?

Apr 14, 2017 | 1989 Toyota Camry

1 Answer

When I put my 95 windstar into drive or reverse I get a wheel hop and thump sound. Drives fine other than that. do you think its ball joint, motor or trans mount?


well without hearing it, i would think its a cv-shaft that has too much play banging around there...at the same time, it also sounds like it could something internal in the trans spinning too far before engaging....mounts usually makes noise under load..just after you put it in gear, and step on the accelerator pedal, you will then hear a clunk..not as soon as you put it in gear, unless extremely bad.

Nov 19, 2009 | 1996 Ford Windstar

1 Answer

1966 mustang coupe motor 289,4 barrel carb.automatic trans. makes a noise when put in reverse,is this normal?


What kind of noise? A clunk, chatter, whir, grinding, or what? If it's a clunk, you may have a worn U-joint. Test by holding brake on and change between drive and reverse and back. If you hear a "clunk" when the tranny engages, it's probably a worn U-joint. Not a hard repair to do in the driveway. Always change BOTH front and rear U-joints - if one's worn, so's the other.

Oct 28, 2009 | 1966 Ford Mustang

2 Answers

When going in reverse i hear a clunking noise from


There are 6 lube points on the drive shafts and u-Joints, check to see these are fully lubed. The drive line will "Klunk" when dry.

Jul 13, 2009 | 1995 Toyota Land Cruiser

1 Answer

Possible Tranny problem...


I am sorry to have to tell you this but it sounds to me like your transmission is shot and will need a rebuild. If you can get it to a transmission shop they will tell you 100% what wrong with it. .

Apr 06, 2009 | 1998 Dodge Grand Caravan

1 Answer

Clunking in tire


check ball joints by lifting front end and shake tires. if loose your ball joints are bad. you will hear a clunking sound as you apply brakes during driving. its the play in the ball joint. the dealer wants $600 in labor. $160 in parts at auto zone. get the ball joint press also. good luck.

Jan 27, 2009 | 2003 Ford F250 Super Duty Crew Cab

1 Answer

2001 toyta camry clunk when put in reverse


check your rear engine mount the one closest to the firewall
kind regards ****

Oct 12, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
2003 Chevrolet Tahoe Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...