Question about Chevrolet Silverado 1500

1 Answer

Distributor cap wiring - Silverado 1500 Chevrolet Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 645 Answers

18436572 is the firing order going clockwise on the cap. Plugs from front to back on passengerside. 2468. Driverside front to back 1357.

Posted on Jan 02, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Spark plug wiring from distributor cap to spark plugs on a 95 honda civic dx 1.5 liter 16 valve sohc


If you look at the distributor cap from the wires side carefully, you would find either a line mark on one of the outer side of four holes (where the spark plug wires are inserted) or the numbers printed on the top of distributor cap (1,3,4,2). Fix one end of the longest high tension plug wire into number 1 hole or the one marked with a line mark on the distributor cap and the other end on spark plug number 1 (the number 1 plug is toward the pulleys and the belts side, then No 2, No 3 and No 4). While standing in front of right wheel you will see the distributor cap in front of you. The rotor moves clock wise. After you fix the 1st cord, next comes number 3 plug wire. Insert one end of the cord into the next to 1 on the right hand side and press the other side of the cord on spark plug number 3. Next to 3 is the cord number 4 and the last one is number 2.

Mar 22, 2013 | Honda Civic Cars & Trucks

Tip

How to Replace a Distributor Cap in Toyota?


Its a plastic cap and and on its top the sparks wires get connected.A small plastic rotor spins inside the distributor cap, firing each spark plug as it rotates. If the distributor gets faulty there the engine may not perform well. in most cases it has been noticed that only replacing the cap does not helps but with cap the rotors also need to be replaced. The procedure is as follows:--- 1) First of all disconnect the negative battery terminal. 2) Then remove the spark-plug wires . Note:-- Before removing the spark plug wires please note down how and where the wires are connected,then only remove the connections. 3) Then on the distributor there will be a cap.remove that cap.the cap is connected by two pins.you will have to press the pins from each side to loosen the distributor cap.Then lift the distributor cap from the top. 4)Then remove the rotor From distributor The rotor is fitted with two screws.Remove the screws and loosen the rotor. 5) Then lift the rotor out from its shaft. 6) To install new rotor and cap.reverse the procedure. This will help.Thanks.

on Mar 25, 2010 | Toyota Corolla Cars & Trucks

1 Answer

Is it hard to change distributor on 2000 nissan pathfinder


Hi there;This is for a 2000 Nissan Truck Pathfinder 4WD 3.3L SFI 6cyl


Distributor Cap & Rotor - Removal & Installation


NOTE
The 1996-00 3.3L engines were equipped with a distributor.


Disconnect the negative battery cable.
If the distributor cap is to be replaced, mark the ignition wires for identification and remove them from the distributor cap.
Remove any components necessary to access the distributor cap.
Completely loosen the distributor cap mounting fasteners.
Carefully remove the distributor cap, taking care not to damage the cap seal or rotor, then position the cap aside.
If necessary, remove the rotor retainer.
Carefully lift the rotor off the distributor shaft.
NOTE
Inspect the distributor cap to housing seal for damage and/or cracks. Replace if cracks are detected.




To install:


Install the rotor onto the distributor shaft and tighten the rotor mounting fastener, if equipped.
Position the distributor cap seal on the distributor housing, then position the distributor cap on the housing.
Install the distributor cap by tightening the mounting fasteners in a crisscross pattern. Use care to not over-tighten the fasteners.
Reconnect the spark plug wires, making sure to install them exactly in the same position from which they were removed.
Reconnect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 06, 2012 | Nissan Pathfinder Cars & Trucks

1 Answer

I need the diagram for plug wiring for 1992 ford tempo


Firing order is 1-3-4-2 Please rate if this helps

Installation of wires
  1. Whenever a high tension wire is removed for any reason from a spark plug, coil or distributor cap, or a new high tension wire is installed, Silicone Dielectric Compound WA-10, D7AZ-19A331-A (ESE-M1C171-A) or equivalent must be applied to boot before it is reconnected. Using a small clean tool, coat entire interior surface of boot with Silicone Dielectric Compound WA-10, D7AZ-19A331-A (ESE-M1C171-A) or equivalent.
  1. Insert each wire on proper terminal of distributor cap. Ensure wires are all the way down over their terminals. The No. 1 terminal is identified on cap. Install wires starting with No. 1 terminal.
  1. Remove wire retaining brackets from old high tension wire set and install them on new set in same relative position. Install wires in brackets on valve rocker arm covers.
  1. Connect wires to proper spark plugs.
  1. Install coil wire.


Installation of distributor
Before installing distributor, visually inspect distributor. Inspect O-ring. It should fit tightly and be free of cuts. The drive gear should be free of nicks, cracks and excessive wear. Rotate distributor drive shaft. It should move freely, without binding.
  1. To install distributor correctly, No. 1 piston must be at Top Dead Center (TDC) of compression stroke. Remove No. 1 cylinder spark plug and rotate engine clockwise until No. 1 piston is on the compression stroke.
  1. With No. 1 piston on compression stroke, align timing pointer with TDC on the crankshaft damper.
  1. Align locating boss on rotor with hole on armature. Fully seat rotor on distributor shaft.
  1. Rotate distributor shaft so blade on rotor is pointing toward mark on distributor base, that was previously made in Step 2 of the Removal procedure.
  1. While installing distributor, continue rotating rotor slightly so leading edge of the vane is centered in vane switch stator assembly.
  1. Rotate distributor in block to align leading edge of vane and vane switch stator assembly. Verify rotor is pointing at No. 1 mark on distributor base. If vane and vane switch stator cannot be aligned by rotating distributor in cylinder block, remove distributor enough to just disengage distributor gear from camshaft gear. Rotate rotor enough to engage distributor gear on another tooth of camshaft gear. Repeat Step 1 if necessary.
  1. Install distributor hold-down clamp and bolt. Tighten bolt, but leave it loose enough to rotate distributor.
  1. Install distributor cap, No. 1 spark plug and ignition wires. Check that ignition wires are securely connected to the cap and spark plugs. Tighten distributor cap hold-down screws to 2.0-2.6 Nm (18-23 lb-in).
  1. Reconnect distributor to wiring harness.
  1. Set initial timing according to procedures found in Section 13A of the Powertrain Control/Emissions Diagnosis Manual .
  1. After timing is set, tighten distributor hold-down bolts to 23-34 Nm (17-25 lb-ft).
  1. Recheck initial timing. Adjust if necessary.

Oct 11, 2011 | 1992 Ford Tempo

2 Answers

Not sure how to replce spark plug wires from the distributor need help please send info


change one spark wire at a time on the distributor.buy new set of spark plugs wires remove them from box.match old wires with new wires to use the correct length to each cylinder.now if you need to change distributor cap.mark location distributor cap.number tag plug wires on the distributor cap so you can remove plug wires on distributor cap so you can replace cap and rotor and put wires back on the distributor cap in correct place.remember change one plug wire at a time so you wont get confuse.

Apr 15, 2011 | 1992 Ford Tempo

1 Answer

I need to replace ,the rotor button...


TAG OR NUMBER ALL SPARK PLUG WIRES ON THE DISTRIBUTOR CAP BEFORE REMOVING CAP. SO YOU CAN PUT PLUGS WIRES BACK IN THE ORIGINAL POSITION. WHEN ALL PLUGS WIRES ON DISTRIBUTOR CAP BEEN NUMBER.REMOVE ALL PLUG WIRES ON CAP.THEN REMOVE THE DISTRIBUTOR CAP.THEN MARK ROTOR POSITION WITH SHARPIE MARKER THEN REMOVE THE ROTOR.

Mar 02, 2011 | Chevrolet 1500 Cars & Trucks

2 Answers

How do I change the distributor


REMOVAL NOTE: Once the distributor is removed, the engine should NOT be turned or moved out of position. Should this occur, please refer to the engine rotated installation procedure. Distributor components — 4A-F engine 88272p61.jpg
Fig. 1: Exploded view of the distributor — 4A-F engine 88272g41.gif
Fig. 2: Exploded view of the distributor — 1993 4A-FE and 7A-FE engines 88272g42.gif
Fig. 3: Exploded view of the distributor — 1996–97 4A-FE and 7A-FE engines 88272g43.gif
Fig. 4: Exploded view of the distributor — 4A-GF engine 88272g44.gif
  1. Disconnect the negative battery cable.
  2. Disconnect the distributor wire(s) at its harness. Loosen the screws holding the cap onto the housing 88272p05.jpg
    Pull the cap and wires off the distributor housing 88272p06.jpg

  3. On the 4A-F engines, disconnect the vacuum advance hoses. NOTE: On some models the distributor wires are part of the cap and can not be separated.
  4. Remove the distributor cap. Label and disconnect the wires from the cap. On some engines it will be necessary to use a flat bladed tool to lift up the lock claw and disconnect the holder from the cap. Fig. 5: On some engines, use a flat bladed tool to lift up the lock claw to disconnect the holder from the distributor cap 88272g45.gif

  5. Carefully note the position of the distributor rotor relative to the distributor housing (also note position of distributor to the engine assembly); a mark made on the casing/housing will be necessary for reassembly. Use a marker or tape so the mark doesn't rub off during handling of the case/housing. Mark the position of the rotor relative to the distributor housing 88272p07.jpg
    Label and remove all vacuum hoses attached to the advance on the distributor if equipped 88272p14.jpg
    If necessary, remove the rotor 88272p08.jpg

  6. Remove the distributor hold-down bolts. Remove the distributor hold-down bolts before pulling the unit from the engine 88272p13.jpg

  7. Carefully pull the distributor from the engine assembly. Remove the O-ring from the distributor shaft. Pull the distributor straight out from the engine 88272p15.jpg
prev.gif next.gif

Aug 13, 2010 | 1996 Toyota Corolla

3 Answers

Changed distributor cap now car will not crank


You should check to make sure that the rotor button is in place. Also check the coil wire and the fire orderr to make sure that no wires are crossed. These are pretty much the only reasons why your car won't crank with the distributor cap change.

Aug 05, 2010 | 1985 Oldsmobile Cutlass Supreme

1 Answer

Distributor cap


follow sparkplug wires back to distributor cap. all wires will lead either to a distributor cap or a coil pack in the case of a coil pack its a closed system which is non servicable. hope this helps.

Nov 02, 2008 | 2005 Jeep Liberty

2 Answers

1987 GMC Jimmy Distributor cap and Rotor replacement


A diagram may not be needed as its a reasonably easy fix to do on your own.the distributor ca p will only fit on properly one way because at the base of the cap locaters can only fit the distributor if they line up.When doing the spark plug leads do them one at a time and if nessecary write or mark leads as 1,2 etc .The rotor can only fit on one way but put a mark on the distributor to show where the rotor was pointing when you took it off and if it still points there when the new one is fitted.When changing distributor cap and leads they have to go to the correct place.Pays to mark the outside of distributor cap where the locating bits are On the new and old one.Fit the new cap and rotor then take a spark plug lead and fit to new cap 1 at a time.You can tell by lining up the marks on the outside of the distributor cap when you hold them one on top of the other.Good luck

Oct 20, 2008 | 1987 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...