Question about 1994 Lincoln Town Car

Open Question

What size wrench 94 lincoln town car rear brake caliper. need to change pads is bolt head covered by a boot

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
chuckster57
  • 1102 Answers

SOURCE: on my 2006 lincoln Nav I need to know what size

The newer fords like to use a 9mm..not very common.

Posted on Jan 14, 2011

Ad
mgomez0824
  • 351 Answers

SOURCE: do you know what hex

T 45

Posted on Jan 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What size allen needed to remove break pads


Allen wrenches usually come in a set, try 3/8.

Apr 30, 2016 | 2008 Chevrolet Chevrolet Impala LS

3 Answers

What tool do I use to remove the calipers to replace disc pads?


I believe it uses a "hex head". You can buy a set of them from most auto parts stores, Sorry I don't remember the size right off hand.

Jan 12, 2011 | 2001 Kia Sephia

2 Answers

How do you change the brakes on a 2004 chrysler town and country and where can you get the brakes for cheap?


Tools you may need: New Brake Pads, Jack and Jack Stands, Lug Wrench, Large Phillips Head Screwdri
Click on the link above for a few tips on how to start this job. Cheep parts can be found at any auto part store just ask for the lowest cost replacement pads and shoes they have. The front pads wear about 2x times faster than the rear shoes. So other than looking at them (rear shoes) I would just advise you to go for the front pads.

Aug 22, 2010 | 2004 Chrysler Town & Country

2 Answers

What tools do I need to replace the rear brakes and the rear rotor


There is a cheap brake piston retractor kit they sell at Harbor Freight that helps a great deal, because you have to rotate the pistons in the rear calipers, as you push them back in. That is because the rear brakes also act as parking brakes, so can't be allowed to retract. That is all you really need in the way of tools except for the right socket/torex/allen for the caliper bolts. I don't know that exact size/shape of the bolt heads because they change.

Jan 20, 2010 | 2006 Volkswagen Passat

1 Answer

I have a 2003 chevy avalanche, and i need to replace my rear brakes and need step by step instruction. I am not a mechanic but know a little. Please thank you


jack up the rear of the car remove wheels and tires, remove the two caliper bolts, remove old brake pads, using a c clamp push each piston the the caliper bake in install new pads, reinstall caliper install wheels and tires lower the jack and your done
caliper bolts are torque head bolts be sure to have the proper size before trying to change the brakes

Sep 27, 2009 | 2003 Chevrolet Avalanche

1 Answer

Instructions Instructions for Replacing Rear Break Pads. Hyundai


Things You'll Need:
  • New brake pads
  • C-clamp
  • Allen head, star head, or 6-point socket wrench
  • Lug nut wrench
  • Brake fluid
    Remove the old Brake Pads
  1. Step 1 Park your car on a level surface. If you have a stick shift car, make sure the car is in gear. Place blocks in front of the front tires so the car does not move while you are working on it.
  2. Step 2 Open the hood of your car. Locate the master cylinder and brake fluid container. If necessary, remove brake fluid until the level in the container is less than half full. A turkey baster is a good tool for this. Put the brake fluid in the plastic container and dispose of it the way you dispose of motor oil.
  3. Step 3 Raise the rear end of your car with your car jack. Remove the rear tire or wheel assembly.
  4. Step 4 Use the socket wrench to remove the lower caliper bolt from the back of the caliper. Rotate the caliper up.
  5. Step 5 Remove the brake pads from the caliper.
  6. Install the new Brake Pads
  7. Step 1 Insert the pads into the caliper.
  8. Step 2 Place a large C-clamp on the body of the caliper and slowly tighten the clamp evenly. Compress the piston until it is flush with the caliper.
  9. Step 3 Lower the caliper and use the socket wrench to attach the lower caliper bolt. Tighten the bolt to 16 to 24 ft. lbs. (22 to 32 Nm).
  10. Step 4 Replace the tire wheel assembly tire. Lower the car to the ground. Pump the brake pedal a few times to seat the brake pads.
  11. Step 5 Add fluid to the master cylinder container to replace any you removed before you removed the old brake pads.
  12. Step 6 Season the brake pads by making only gentle stops when you are driving for the first week after you install the new brake pads. Try not to do any hard stopping when you are seasoning the brakes.

Jul 08, 2009 | 2005 Hyundai Tucson

1 Answer

I have a 2000 Passat and going to have my friend replace the rotors and breaks. I am preparing to fix it but want to know what sizes are the bolts for the calipers sliding pins. If you know the Bolt s


For a wrench or for the acctual bolt size.
To remove front pads..you need 8mm allen socket to pull the caliper guide pins, then 17 or 18mm..To remove rear pads...you need 13mm socket for lock bolt on guide pins and 15mm open end wrench (thin section to hold guide pin while you remove lock bolts..I ground down a spare wrench). You DO NOT have to remove rear carriers to change rotors..just remove lock screw and angle rotor out. The B5 Passats don't have the electronic parking brake so you don't need VAG Com to change pads.
Installation tips:
Clean and regrease the guide pins with "synthetic caliper grease"
Rear lock bolts come with preapplied thread locker and "are not to be reused"..I just wire brush the threads and use some Loctite Blue on em. I smear just a little antisieze on the inside bore of the rotors and on the lock screw threads to prevent corrosion and make next rotor change ez. Torques:
Front caliper guide pins:18 ft lb
Front carrier bolts: 89 ft lb
Rear guide pin lock bolts:26 ft lb
Wheel lugs: 89 ft lb

May 29, 2009 | 2000 Volkswagen Passat 4Motion

1 Answer

Rear brake pad installation 99 volkswagen passat


If you can't see diagrams(sometimes happens) let me know and I will get them to you

  1. Raise and support the vehicle. Remove the rear wheels.
  2. If equipped, disconnect the brake pad wear sensor from the harness.
  3. Counterhold the lower sliding pin using a thin open-end wrench and remove the caliper-to-sliding pin hex bolt.
  4. Pivot the caliper upward or if necessary remove the upper caliper-to-sliding pin hex bolt.
  5. Using a brake caliper retraction tool, select the appropriate sized piston press arbor and install the tool onto the brake caliper. Following the tool manufacturer's recommendations, use the tool to rotate the caliper piston clockwise as it is pressed into the brake caliper housing, until it is fully retracted.
0900c152800c30b8.jpgUse a thin open-end wrench to . . . 0900c152800c30b7.jpg. . . support the caliper sliding pin when removing the caliper mounting bolt 0900c152800c30d7.jpgUse a disc brake caliper piston retracting tool that will rotate the caliper piston as it is pressed into the caliper 0900c152800c30d8.jpgThe rear caliper piston is slotted to allow a retracting tool to rotate the piston when replacing the brake padsTo install:
  1. Clean the brake caliper and all sliding surfaces. With the caliper piston pressed fully back into the caliper housing, check for leaking fluid and damaged dust boots.
  2. If equipped, install a new brake pad wear sensor in the pad if the plastic part has been worn through on the old sensor. New sensors are not required unless the wire inside the plastic part has been exposed.
  3. Lubricate the slider bolts with approved brake grease.
  4. Install the brake pads onto the bracket assembly, and then carefully lower the caliper over the caliper mount. Check and make sure that the pad springs are correctly seated.
  5. Replace all removed caliper-to-sliding pin bolts and torque to:
  6. 1990-97 Passat models: 25 ft. lbs. (35 Nm)
  7. 1998-00 Passat models: 22 ft. lbs. (30 Nm)
  8. If equipped, connect the brake wear sensor wire to the harness. Check for a good connection as most problems with the sensor circuit are caused by faulty connections. Check that the wire is held by the loop in the dust cover and the connector is held at the clips.
  9. Install the wheels and hand tighten the lug bolts. Lower the vehicle carefully until the tires begin to contact the surface and torque the lug bolts to specification in a crisscross pattern to:
  10. M12 x 1.5 lug bolts: 81 ft. lbs. (110 Nm)
  11. M14 x 1.5 lug bolts: 89 ft. lbs. (120 Nm)
Feel free to contact if you have any questions

Nov 15, 2008 | 1999 Volkswagen Passat

Not finding what you are looking for?
1994 Lincoln Town Car Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...