Question about 1983 Mazda RX-7

2 Answers

1983 rx7 was sitting for a period of time now the clutch will not work

Posted by on

  • Fernand Luc Bergeron
    Fernand Luc Bergeron Jan 02, 2011

    any fluid in the clutch canister ?

  • truffulaseed Jan 02, 2011

    Will the clutch not engange, or will it not disengage?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I had the same problem with my 83', i bought a new slave cylinder and everything, b ut decided just to bleed the old one out and that did the trick, now it works like a champ, it should be located on the bell housing u can get to it from under the hood
hope this helps

Posted on Apr 25, 2012

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 90 Answers

Your problem may well be that the throwout bearing, which is located inside the bell housing in between the engine and the transmission has become stuck.

Posted on Jan 02, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's your problem?1983 mazda rx7 backfires when getting off gas pedal


sounds like the timing is out or the fuel mixture is wrong get a tune up and that will prob sort it

Oct 25, 2012 | Mazda Cars & Trucks

1 Answer

Needs to buy fusbile links for my 1983 mazda rx7


Ebay is likely the best place, as most bone yards dont have first gen RX7s anymore. I checked and they are very cheap 10$ max

Dec 23, 2011 | 1983 Mazda RX-7

1 Answer

Headlights will not open on 1983 mazda rx7


  • well if you havent checked your fuses there is a fuse that will keep them from goin up or your switch is bad and you may have to replace it. that what i had to do with mine.
  • Dec 05, 2011 | 1983 Mazda RX-7

    1 Answer

    Where is the fuel pump on a 1983 mazda rx7?


    Yes it is right next to the fuel tank, under a metal cover. It is on the driver's side in front of the rear axle

    Sep 29, 2011 | 1983 Mazda RX-7

    1 Answer

    Replace clutch plate on 1992 mazda rx7


    You will have to drop the transmission. Inspect the pressure plate for excessive wear and stretched springs when you remove it. Replace your throwout bearing at the same time, they are usually worn out by the time you need a clutch.
    Mike

    Jun 14, 2011 | Mazda RX-7 Cars & Trucks

    1 Answer

    Clutch sticking will not go into first


    Ok it looks like there is no problem with the clutch or tranmission. You problem is that the clutch pedal is stiff and sticking to the floor. This sometimes happens when vehicles sit for extended periods of time. It might free up by working back and forth by hand. Have the vehicle off and the parking brake applied and push the clutch pedal up and down with your hand, It might stick to the floor and you may have to pull it off the floor a few times. You can also get some spray lubricant from your local canadian tire or auto parts store. open the hood and have someone move the clutch pedal up and down and spray the moving parts. It might take a few times to free up the stiff linkage but it will work :)

    Mar 07, 2011 | Nissan Se R Cars & Trucks

    1 Answer

    How do i change the clutch on a 1983 mazda rx7


    with great difficulty ,its a dirty hard backbreaking job ,now is it front wheel drive or rear wheel drive

    Dec 30, 2010 | 1983 Mazda RX-7

    1 Answer

    My 1983 Jetta starts perfect but then only runs for 2 seconds and then dies as if I turned the key off. It had been sitting for a couple of years and I just replaced the fuel pump because the one on it...


    It could be a clogged fuel filter, I would change that and throw a bottle of STP Super Concentrated Fuel Injector Cleaner in your tank. When a vehicle sits for a long period of time the fuel inside of the tank and lines gets gummy and forms varnish deposits on and in parts. You want to make sure you clean all of that out so your car does not have any issues in the future.

    Jun 10, 2010 | 1983 Volkswagen Jetta

    1 Answer

    83 Rx7 stalls when cold unless I keep applying pedal pressure


    these cars are carburated motors and need around 10 minutes to warm up because they operate at higher temperatures.

    Aug 06, 2009 | 1983 Mazda RX-7

    2 Answers

    Wiring diagram for a 1983 rx7


    dear friend-plse go to the following web site and you will find a manual with everything in it.
    WWW.BOOKS4CARS.COM enter under mazda then put in year model and there you are.

    Jul 17, 2009 | 1983 Mazda RX-7

    Not finding what you are looking for?
    1983 Mazda RX-7 Logo

    Related Topics:

    110 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mazda Experts

    yadayada
    yadayada

    Level 3 Expert

    75807 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22133 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8172 Answers

    Are you a Mazda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...