Question about 2005 Jeep Liberty

Open Question

2005 Jeep Liberty, 4X4, 3.7L Automatic Transmission. 2 options, 3 or 4 wire connectors. Can you tell by the VIN if it is 3 or 4 wire connector?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

michigan man
  • 3533 Answers

SOURCE: how to replace rear brake pads on 2005 jeep liberty

put the back of car on jack stands and secure the front tires so it does not roll and then remove the bolts off the back of the caliper there is normally two one at top and one at bottom and spray it with some kind of oil for rust and make sure you have the right size socket before you try to loosen them and once caliper is off and the old pads removed take one of the old pads and squeeze the piston on the caliper back in by using a "C" clamp and also remove some of the brake fluid from the master cylinder before you do this put the new ones back on and check the brake fluid and make sure it is full and then pump the brakes to make sure you have a good pedal also put some "No Squeak" brake stop on the back of the pads so they don't squeak they will have that where you buy the pads from

Posted on Mar 01, 2009

c17hydro
  • 2984 Answers

SOURCE: Identifying 2003 Jeep Liberty Automatic Transmission

What is your VIN number?

Posted on Mar 31, 2009

  • 6982 Answers

SOURCE: rear suspension,bushings,2005 jeep liberty

Generally the bushings aren't too expensive (likely about 25-30 each...But, unless you have done this kind of work, driving the bushings out and installing them can be difficult without a press. I've done many in-shop and its nothing like the ones I've done at remote locations using a hammer and chisels etc. You can do this yourself but I'd opt to do the r&r at home and have a machine shop do the actual bushing pressing. If you damage the arm ends you will need to replace the arm or do a bunch of bending to get the bushings back in place.
If you do have a press, than go at it!!

Posted on Aug 02, 2009

  • 249 Answers

SOURCE: 2005 jeep liberty brake lights will not work. I

brake pedal switch, get a wire, unplug plug, bridge circuit and check lights.
plug and switch is high up on the brake pedal not normally easy to get to.

Posted on Aug 15, 2009

  • 811 Answers

SOURCE: Jeep Liberty CD Player problems

try using canned air to clean

Posted on Oct 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3.7l. Where can I get a wiring diagram for engine installation?


engine missing? harnessed missingn
connectors on harness bad. what?
all the connectors are unique, there no mixing them up.
try to say why things dont seem to match.?
the fsm has that, in spades, the factory serv. manual
even has diagram photos that tell this exaclty
unlike online books missing this whole chapter (common )

Jan 23, 2016 | 2005 Jeep Liberty

1 Answer

Tengo jeep liberty 2005 me dio code de p0700 y p0204 que debo chequear


which engine?, , please avoid spanish here, its a USA english forum.
p07 codes, are transmission.
p0204 is mostly....

the codes are just tests that fail.
and a tech, sees the words in the FSM that tell him what tests need to be done by humans to find true cause.
see?
the tests is for injectors
and the causes are , listed
(F142) ASD RELAY OUTPUT CIRCUIT
(K14) INJECTOR CONTROL NO.4 CIRCUIT OPEN
(K14) INJECTOR CONTROL NO.4 CIRCUIT SHORTED TO GROUND
FUEL INJECTOR
PCM

first id look for bad injector 4 wires.
then pull connector and see if OHMS (resistances) of coil pins'
is wrong (try other injector and compare them)
0 ohms shorted
infinity is open oil
if resistance is not near others, its burned up. damaged.
keep in mind coils can be partial shorts. do to the windings damaged. like all coils can do, or motors.

Mar 25, 2015 | 2005 Jeep Liberty

1 Answer

My 2005 Jeep Liberty is stuck in 4 Lo and only goes to neutral, not 4 Hi or 2 Hi. I checked the transfer case and the cable was broke. How do I get it back in 2 Hi? I need to before I fix the cable. Also,...


nice double post and not one mention if what case it has.
NV- zzz
231,241,242 transfer case.
(its and options day one out of factory)_as is transmission,
backup one post and see the answer.

Mar 20, 2015 | 2005 Jeep Liberty

1 Answer

I have got the starter diconnected from my 2005 5.7 jeep gc but I cant get it out to replace it


1. Disconnect and isolate negative battery cable.
2. Raise and support vehicle.
3. Note: If equipped with 4WD and certain transmissions, a support bracket is used between front axle and side of transmission. Remove 2 support bracket bolts at transmission. Pry support bracket slightly to gain access to lower starter mounting bolt.
4. Remove two mounting bolts (2).
5. Move starter motor towards front of vehicle far enough for nose of starter pinion housing to clear housing. Always support starter motor (1) during this process, do not let starter motor hang from wire harness.
6. Tilt nose downwards and lower starter motor far enough to access and remove nut that secures battery positive cable wire harness connector eyelet to solenoid battery terminal stud. Do not let starter motor hang from wire harness.
7. Remove battery positive cable wire harness connector eyelet from solenoid battery terminal stud.
8. Disconnect battery positive cable wire harness connector from solenoid terminal connector receptacle.
9. Remove starter motor.

May 14, 2011 | 2005 Jeep Grand Cherokee

1 Answer

How do i change the blower motor resistor in my 2005 jeep liberty?


Dealership should have the replacement for $20 or less. Get the new one before you take the old one out so that you can see what it looks like, what to look for and how it goes in.
Removal is simple. Under the passenger side dashboard, you'll see a wiring harness that goes to a socket which is held in place by 2 screws.
Unplug the wiring harness from the connector. Remove the 2 screws and it'll drop right into your hands.
Installation is just as simple. Hold the new one in place and replace the 2 screws. Plug the wiring harness back in and you'll be good to go!

Nov 20, 2010 | 2005 Jeep Liberty

1 Answer

On a 2005 Jeep Liberty, the passenger headlight went dim. I replaced the bulb but no improvement. I switched the bulb with the driver side, and still no improvement. No the passenger light is out. The...


there is a ground wire for both sides. follow the wire from the connector to body and clean, Test the 12 volt wire to make sure it has 12 volts. If not bad switch or bad wire or contact in the connector. Wiggle the connector first with the lights on to see if it changes.

Nov 24, 2009 | 2005 Jeep Liberty

1 Answer

2004 jeep liberty replacing the starter


2004 Jeep Liberty 4WD 3.7L MFI SOHC 6cyl
Starteer - Removal & Installation

2.4L & 3.7L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Remove the starter mounting bolts.
  4. On the 3.7L engine, the left side exhaust pipe and front driveshaft must be disconnected.
  5. Disconnect the starter solenoid harness connections.
  6. Remove the starter.
To install:

8222c5e.jpg

Fig. Starter mounting: 2.4L engine

1ab95e7.jpg

Fig. The starter position for the 3.7L engine
  1. Connect the starter solenoid wiring connectors.
  2. Install the starter and torque the bolts to 40 ft. lbs. (54 Nm).
  3. On the 3.7L, the left side exhaust pipe and front driveshaft.
  4. Install the negative battery cable and check for proper operation.

2.8L Engine
  1. Disconnect and isolate negative battery cable.
  2. Raise and support vehicle.
  3. Disconnect solenoid wire connector from solenoid terminal
  4. Remove battery cable from stud on starter solenoid.
  5. Remove 3 starter mounting bolts.
  6. Remove starter from transmission bellhousing.
To install:
  1. Position starter motor to transmission housing.
  2. Connect battery cable solenoid terminal wire harness connector to connector receptacle on starter solenoid. Always support starter motor during this process. Do not let starter motor hang from wire harness.
  3. Install battery cable eyelet terminal onto solenoid B(+) terminal stud.
  4. Install nut securing battery cable eyelet terminal to starter solenoid B(+) terminal stud.
  5. Refer to torque specifications.
  6. Position starter motor and install 3 bolts. Tighten 3 bolts in this sequence: top bolt, bottom bolt, middle bolt. Refer to torque specifications.
  7. Lower vehicle.
  8. Connect negative battery cable.

Also can review the Service Repair Manual for Jeep KJ Liberty

I really hope help you with this (remember rated this help) Good luck.

Oct 04, 2009 | 2004 Jeep Liberty

1 Answer

2005 jeep liberty 4 weel drive will not engage


I just bought a jeep liberty, 2005. It's automatic with 4wheel drive option. I do not have an owners manual. Do not know how to engage the 4wheel drive. I have never had a 4wheel drive vechile before.

Jan 15, 2009 | 2003 Jeep Liberty

2 Answers

Transmission


Transmission
Typo and model:
1.- 4-speed automatic AW-30-40 (6cil start of 1993)
2.- 4-speed automatic 42RE ( 6cil 1993)
3.- 4-speed automatic 46RH ( V8, 1993-1995)
4.- 4-speed automatic 44RE ( 5.2L V8, 1996)
5.- 4-speed automatic 46RE ( 5.9L V8, 1998)
6.- 5-speed automatic 45RFE( 4.7L V8, 1999 in WJ)

Enter the VIN in here: http://jeep.avtograd.ru/VIN/vin_en.asp

Also cHeck this info: http://www.jeep.com/en/4x4/systems_by_vehicle/

Good luck!!!

Dec 05, 2008 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
2005 Jeep Liberty Logo

Related Topics:

334 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...