Question about 1992 Toyota Tercel

1 Answer

Need to remove the water pump - 1992 Toyota Tercel

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 112 Answers

Hope this helps, it it does please leave feedback and vote Thank You and Good Luck


WATER PUMP REMOVAL

  1. REMOVE RH ENGINE UNDER COVER
  2. DRAIN ENGINE COOLANT
  3. REMOVE GENERATOR (See page CH-8)
need to remove  the - 91329747


  1. REMOVE INTAKE MANIFOLD STAY
  1. REMOVE WATER INLET PIPE
(a) Disconnect the following hoses: 91329748


(1) Water inlet hose (2) Heater inlet hose (3) Water bypass hose 91329749


(b) Remove the bolt, water inlet pipe and 0-ring.
  1. REMOVE OIL DIPSTICK GUIDE AND GENERATOR ADJUSTING BAR
(a) Remove the oil dipstick. (b) Remove the mounting bolt of the dipstick guide clamp and generator adjusting bar. need to remove the - 91329750img src="http://i.fixya.net/uploads/images/91329750" alt="91329750" class="h_mi" />


(c) Pull out the dipstick guide. Plug the guide installation hole of the oil pump. (d) Remove the 0-ring from the dipstick guide. need to remove the - 91329751 91329751


  1. REMOVE WATER PUMP
    • Remove the bolt, 2 nuts and water pump.

Posted on Jan 02, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to replace a water pump on my plymouth grande voyager se 3.3l


Jack up the passenger side and remove the tire. Remove the splash shield to gain access to the belt and tensioner. Remove the serp belt. Remove the bolts holding the pulley to the water pump. Remove the pulley Remove the bolts holding the water pump to the timing cover. Remove the water pump. Be prepared for the bolts to break. It happens often!

Jul 13, 2013 | Cars & Trucks

Tip

How do I replace the water pump on my Cadillac Deville?


Hi.

Here the instructions.

  • Take off the plastic cover located near the top of the radiator if present.
  • Remove the protective shield located on top of the belt pulling the water pump. You will need to undo two 10mm nuts and one 10mm bolt.
  • Undo the 10mm nut that holds water pump housing togeter with the oil dipstick.
  • Take off the air intake assembly.
  • Move the PCM computer to one side, ensure that the module is safely placed.
  • Release the belt tensioner using a big flat screwdriver.
  • Remove the serpentine belt from the water pump pulley
  • Remove the upper radiator hose. This is held by a metal clamp. Use plyers to remove the clamp.
  • Remove also the clamp from the thermostat housing bypass hose, without removing the hose (you have to bleed coolant first).
  • Unscrew the four 10mm bolts that hold the water pump housing and letcoolant drain from water pump plug. At this point you can also removethe lower radiator hose to drain faster.
  • After coolant drains remove the water pump housing.
  • At this point you have to use a special Water Pump removal tool onwater pump cand turn clockwise until the pump is sliding off thehousing.
  • Remove the pump and the o-ring located inside the water pump housing.
  • Clean and grease the area, put a new o-ring and install back water pump housing
  • Install the new water pump using the special tool and following operations in reverse order.

You may need to use sealant tabs from a Cadillac or GM dealer. Here is what you need.
Better going to your local dealer to get the best product for yourCadillac. You will also need a 3/8'' ratchet, socket and extensions

Youmay also need to replace the housing cover gasket. You will need toreplace the O-Ring, that usually comes with the new pump.
When installing new pump you must also ensure that the new pump is aligned correctly,one of the tabs on the pump housing is different and will lock up the pump, so it must bealigned properly while installing.

Here pump:2000 Cadillac DeVille Water Pump

Here the special tool: Water Pump Removal and Installation Impact Socket

on Mar 16, 2010 | 2000 Cadillac DeVille

1 Answer

Replace water pump torrent


drain coolant until below water pump level. loosen water pump pulley bolts.then remove drive belt by rotating belt tensioner.remove drive belt from the right of idler pulley.carefully release the drive belt tensioner spring tension.then remove water pump pulley bolts and pulley.remove water pump bolts and water pump pay attention to the position old water pump when removing water pump so you can line up new water pump holes to the engine. be sure clean engine water pump mounting surface use gasket remover dont scratch engine surface when cleaning removing old gasket material. take new water pump gasket get it mounting holes line up with new water pump mounting holes.when done getting engine water pump surface clean.water pump gasket paper you need to put thin layer of sealer on both sides of water pump gasket use RTV SILICONE.LET SET UP 10 MINUTES. PUT GASKET ON WATER PUMP BUT FIRST MAKE SURE LINE UP GASKET HOLES WITH WATER PUMP HOLES BEFORE PUTTING ON THE GASKET SEALER.when gasket sealer set up 10 minutes then install new water pump with gasket to the engine torque to 89 inch lbs.or 10 NM that is about 7 ft lbs torque.you should be able turn water pump by hand if you cant turn water pump by hand got too tight damage water pump shaft bearing.when all done wait for THREE HOURS. before adding coolant i let RTV CURE SOME. torque water pump pulley bolts 18 ft lbs.

Dec 28, 2012 | 2006 Pontiac Torrent

1 Answer

Mercedes 1998 c230 water pump replacement


REPLACE WATER ALL YOU NEED TO DO IS DRAIN THE COOLANT SYSTEM.REMOVE THE ENGINE COOLING FAN AND CLUTCH THEN THE FAN SHROUD.REMOVE ENGINE COVER IF EQUIPPED.THEN REMOVE THE ACCESSORY DRIVE BELT.UNBOLT THE POWER STEERING PUMP MOVE IT ASIDE DONT DISCONNECT ANY POWER STEERING PUMP HOSES.DISCONNECT WATER PUMP HOSES, REMOVE BELT PULLEY THEN REMOVE WATER PUMP MOUNTING BOLTS AND WATER PUMP.CLEAN WATER PUMP MATING SURFACE BE CAREFUL DONT SCRATCH PUMP SURFACE. BESURE WHEN YOU INSTALL NEW WATER PUMP USE GASKET SEALANT ON BOTH SIDE OF GASKET TO KEEP IT FROM LEAKING COOLANT.

Sep 26, 2011 | 2007 Mercedes-Benz C230 Sedan

1 Answer

Need instruction for replacing water pump 2004 GMC Envoy 4.2 liter engine.


TO REPLACE WATER PUMP.FIRST YOU HAVE TO DRAIN THE COOLANT SYSTEM. REMOVE AIR INTAKE DUCT AND RESONATOR. REMOVE THE RADIATOR SHROUD AND FAN CLUTCH ASSEMBLY REMOVE THE DRIVE BELT. REMOVE WATER PUMP PULLEY.YOU NEED A PIN SPANNER WRENCH OR STRAP WRENCH TO HOLD WATER PUMP PULLEY WHILE LOOSEN WATER PUMP PULLEY BOLTS .YOU CAN BUY STRAP WRENCH OR RENT PIN SPANNER WRENCH AT AUTO ZONE PARTS STORES OR OTHER STORES HAS TOOLS CAN BE RENT. ONCE WATER PUMP PULLEY REMOVED. REMOVE THE WATER PUMP MOUNTING BOLTS. REMOVE WATER PUMP. IF WATER PUMP STUCK YOU CAN TAP WITH SOFT FACE HAMMER OR A LONG PIECE OF ROUND WOOD.WHEN WATER REMOVED.YOU NEED TO CLEAN THE SEALING SURFACE CAREFUL DONT SCRATCH SEALING SURFACE. YOU CAN BUY CAN OF SPRAY GASKET REMOVER.CLEAN SURFACE GOOD THEN WIPE WITH LACQUER THINNER OR ACETONE.THEN GET WATER PUMP NEW GASKET MATCH HOLES UP WITH GASKET TO WATER PUMP. ONCE HOLES MATCH UP APPLY RTV SEALANT ON BOTH SIDES WATER PUMP GASKET. THEN PUT GASKET ON WATER PUMP THEN INSTALL WATER PUMP TO VECHICLE.TORQUE WATER PUMP BOLTS TO 89 INCH LBS .TIGHTEN WATER PUMP PULLEY BOLTS TO 18 FT LBS THEN PUT EVERY THING BACK VISA VERSA.

Aug 26, 2011 | GMC Envoy XL Cars & Trucks

1 Answer

Remove and replace the water pump buick rendezvou 2003 cost and do it yourself instructions . can i do it myself concerned with loosening the serpentine belt and needing special tools?


1. Drain the cooling system until the coolant is below the level of the water pump. 2. Remove the drive belt guard. 3. Loosen the water pump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulley bolts. 6. Remove the water pump pulley. 7. Remove the water pump bolts. 8. Remove the water pump. 9. Remove the water pump gasket. 10. Clean the water pump mating surfaces. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump Notice: Refer to Fastener Notice in Service Precautions. 3. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.). 4. Install the water pump pulley. 5. Install the water pump pulley bolts. 6. Install the drive belt. Tighten the water pump pulley bolts to 25 Nm (18 inch lbs.). 7. Install the drive belt guard. 8. Fill the cooling system
Visit my Blog here

Jul 21, 2010 | 2002 Buick Rendezvous

2 Answers

I have a 1999 Ford SHO that needs a new waterpump. I need to know how to replace it and where I can get a schematic of it. Do I need a special tool kit to do it? I'd also like to know where I can get the...


www.autozone.com

They can get all the parts. They also provide haynes repair manuals, any special tools (probably not required for this vehicle) and any special disassembly instructions.

I hope this helps.

Mar 11, 2010 | 2001 Ford Taurus

2 Answers

Do I need any special tools? How Hard is it?water pump 2002 aztek


take everything around your water pump of and use a metric 10 box end wrench

Apr 30, 2009 | 2002 Pontiac Aztek

1 Answer

Water pump


Please RATE ME
This IS EXACT Procedure Bu The BOOK
REMOVAL
  1. Drain cooling system.
  2. Loosen fan clutch attaching bolts.
  3. Remove fan shroud attaching bolts and remove shroud and fan.
  4. Remove drive belt.
  5. Disconnect lower radiator hose, heater hose and bypass hose from water pump.
  6. Remove fan, spacer, water pump pulley and fan shroud.
  7. Remove A/C compressor/power steering pump bracket and accessories to clear water pump stud bolt.
  8. Remove water pump attaching bolts and the water pump.
INSTALLATION
  1. Reverse procedure to install. Tighten water pump retaining bolts to 12-18 ft. lbs.
NOTE: All water pumps have a sealed bearing integral with the water pump shaft. The bearing requires no lubrication. A bleed hole in the pump housing allows water that may leak past the seal to be thrown out by the slinger. This is not a lubrication hole. If the pump is damaged and requires repair, replace it with a new pump or a rebuilt one.
I Need your Help Also !! PLEASE RATE ME

Jan 27, 2009 | 1995 Ford F250

1 Answer

How Do i replace Water Pump on 98 Chevy Metro


  1. Remove the negative battery cable.
  2. Drain the engine cooling system.
  3. Remove the air cleaner assembly.
  4. Remove the A/C compressor suction pipe bracket (if equipped).
  5. Loosen four water pump pulley bolts. Do not remove the bolts.
  6. Raise the vehicle. Support the vehicle. Remove the right lower splash shield.
  7. Remove the right lower splash shield.
  8. Remove the A/C compressor drive belt (if so equipped) by releasing the tensioner pulley and removing the belt from the crankshaft and compressor pulleys.
  9. Loosen the generator adjusting bolt (1), pivot the generator and remove the water pump/generator drive belt.
  10. Remove the crankshaft pulley.
  11. Remove the water pump pulley (four bolts).
  12. Remove the timing belt.
  13. Remove the oil level indicator (dipstick) guide tube.
  14. Remove the upper generator adjusting bracket from the water pump (one bolt).

    1. Remove the rubber seals from the water pump.
    2. Remove the water pump mounting bolts and nuts.
    3. Remove the water pump and gasket from the vehicle.
    4. Clean the water pump and the gasket mating surfaces.
    5. Install the water pump.
    6. Secure the water pump with mounting nuts and bolts. Tighten Tighten the water pump mounting nuts and bolts to 13 Nm (115 ft. lbs.).
    7. Install new rubber seals (1) to the water pump (2).
    8. Install the upper generator adjusting bracket to the water pump (one bolt).
        • Tighten the upper generator mounting bracket bolt to 23 Nm (17 ft. lbs.).
      1. Install the oil level indicator (dipstick) guide tube.
      2. Install the timing belt.
      3. Install the water pump pulley.
      4. Finger-tighten the four bolts.
      5. Install the crankshaft pulley.
      6. Install the water pump/generator drive belt to the crankshaft, water pump and generator pulleys.

Nov 20, 2008 | 1998 Chevrolet Metro

Not finding what you are looking for?
1992 Toyota Tercel Logo

551 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...