Question about 1990 Nissan Pulsar

Open Question

How to check or change a fuel Pump on a Nissan Pulsar 1991 model N14 2 lt Motor Fuel injected

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 67 Answers

SOURCE: 1987 nissan pulsar

Question is, does fuel pump relay come in/ go out when ignition switched on? How do you know "no power source to fuel pump", was that because bypassing the relay didn't cause it to run? Or did you check for supply to the pump and find nothing doing?.
Sounds rather like a frozen pump to me... or a blown fuse??

Posted on May 31, 2008

Ad
fischmilch
  • 96 Answers

SOURCE: Fuel Guage Problem on Nissan Pulsar N14

Either the sending unit in the tank is bad, or the gauge is bad.

Posted on Mar 09, 2009

MARWAT
  • 124 Answers

SOURCE: no spark from 1988 nissan pulsar

BOT MA MAY B ,,,, BUT FIRST CHECK FUSEZ ,,,,, HAVE CHECKED POINT ?

Posted on Jul 23, 2009

  • 407 Answers

SOURCE: 1991 Nissan Maxima wont start

need to know how fuel pressure if way below 36psi maybe why it wont start

Posted on Oct 13, 2009

Wolfman304
  • 720 Answers

SOURCE: how do i get to the fuel pump in a nissan pulsar

Hi there,

The fuel pump is mounted "inside" the fuel tank. You'll need to remove the rear seat (bottom portion) to gain access to the pump assembly.

If fuel is pouring out, then there is an obvious leak from either the hoses (attached to the fuel pump) or from the pump seal in the tank.

Here is the diagram:

57a8a74.gif

Hope this helps...


** If the has helped you in any way, please rate this solution **


Posted on Nov 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1991 Nissan pulsar starts and runs when electric radiator fans kick in engine stops


Get a code reader for Nissan and see if the computer will provide you with an answer. Might be something simple that you could spend lots of time and money trying to find otherwise.

Jan 05, 2015 | Nissan Cars & Trucks

1 Answer

Why do I have to pump the gas pedal to get my 1991 Nissan stanza to start


You probably have a carburetor that feeds fuel to the engine rater than Fuel Injection. Fuel Injection squirts a bit of fuel into the ignition chamber when you turn your key, allowing the car to start, with a carburetor, you have to manually pump the fuel into the ignition chamber to start the engine. Usually Two to Three times should be enough.

Jan 22, 2013 | Nissan Stanza Cars & Trucks

1 Answer

I have a 1991 model hyundai excell and changed the motor to a 1994 x2 motor. The car starts but there is no fuel pressure. I have changed the fuel injectors and the fuel regulator. When I squeeze the fuel...


Lacking fuel pressure.Change fuel pump to the 1994 model type.Squeezing the fuel ret line causes pressure to build up in the line and fuel to pass through injecters more efficiently.

Aug 04, 2011 | 1994 Hyundai Excel

2 Answers

1993 rodeo not running no power to fuel pump


if there is no power to the fuel pump check relays and fuses....UNDERHOOD FUSE & RELAY PANEL IDENTIFICATION Fig. 2: Underhood Fuse & Relay Panel Identification Courtesy of ISUZU MOTOR CO. Fusible Link Identification ? A - 80 Amp (1991-92 3.1L) ? A - 60 Amp Main-1 ? B - 30 Amp Main-2 ? C - 30 Amp (1993-94) ECM (3.2L) ? D - 30 Amp Condenser Fan (A/T Models) Relay Identification ? 1 - Headlight Relay ? 2 - A/C - Heater Relay ? 3 - Starter Relay ? 4 - A/C Compressor Relay ? 5 - Charge Relay ? 6 - Fuel Pump Relay ? 7 - ECM Relay ? 8 - Wiper Relay Fuse & Circuit Breaker Identification ? 1 - 15 Amp (1991) ECM, Fuel Injection System ? 1 - 15 Amp (1992-94 2.6L) ECM, Fuel Injection System ? 1 - 10 Amp (1992-94 3.1 & 3.2L) Heated Oxygen Sensor, Fuel Injection System ? 2 - 20 Amp (1991-92) Fuel Pump ? 2 - 20 Amp (1993-94 2.6L) Fuel Pump ? 2 - 15 Amp (1993-94 3.2L) Fuel Pump ? 3 - 10 Amp (1991) ? 3 - 15 Amp (1992-94) Turn Signal Lights, Hazard Warning Flasher Lights ? 4 - 10 Amp Horn, Door Locks ? 5 - Not Used (1991 3.1L) ? 5 - 10 Amp Charging System, Charge Warning Light WARNING: Always disconnect battery ground cable before servicing "high- current fuses. It is recommended that "high-current" fuses be replaced by a qualified technician. Page 1 of 2 FUSES & CIRCUIT BREAKERS -1994 Isuzu Rodeo LS? 6 - Not Used (1991) (1992-93 2.6L) ? 6 - 10 Amp (1992-94 3.1L & 3.2L) A/T Interlock System ? 6 - 10 Amp (1994 2.6L) Heated Oxygen Sensor, Fuel Injection System ? 7 - 20 Amp Heater/Air Conditioning Blower Controls ? 8 - 10 Amp Air Conditioner Compressor Controls ? 9 - 10 Amp Right Headlight ? 10 - 10 Amp Left Headlight © 2008 Mitchell Repair Information Co., LLC.
62217_isuzfuse_1.jpg
Underhood fuse block swap out relay #7 thats the ECM relay.
Ground Circuits Using a DVOM, touch negative voltmeter lead to a good ground. Touch positive voltmeter lead to each ground terminal. With vehicle running, voltmeter should indicate less than one volt. If reading is greater than one volt, check for open, corrosion and loose connection on ground lead. See ECM GROUND LOCATION table for ECM ground location.
Page 1 of 1 SYSTEM/COMPONENT TESTS - 2.6L EFI -1994 Isuzu Rodeo

Mar 28, 2010 | 1993 Isuzu Rodeo

1 Answer

How do you remove the fuel pump from the fuel tank of a Nissan Pulsar gli 1991 N14 Sedan


Remove bck seat / tank pipes / elctrical wiring plug / unsrew panel and carefully lift out.

NB = Ensure no sparks or you will occupy a hospital bed :)

Dec 23, 2009 | Nissan Pulsar Cars & Trucks

1 Answer

1991 pontiac 2.5 tech 4 fuel pump relay wont energize


Look for a bad fuse or relay. If both check out, most likely an ECM problem

Mar 07, 2009 | 1991 Pontiac Grand Am

2 Answers

1985 nissan exa turbo


a intake problem possibly a fuel pump on the way out or air and fuel filter check plugs and injectors

Jun 16, 2008 | 1985 Nissan Pulsar

1 Answer

1987 nissan pulsar


Question is, does fuel pump relay come in/ go out when ignition switched on? How do you know "no power source to fuel pump", was that because bypassing the relay didn't cause it to run? Or did you check for supply to the pump and find nothing doing?.
Sounds rather like a frozen pump to me... or a blown fuse??

May 28, 2008 | 1989 Nissan Pulsar

Not finding what you are looking for?

Open Questions:

See all 1990 Nissan Pulsar Questions

1990 Nissan Pulsar Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...