Question about 1998 Dodge Stratus

1 Answer

Brakes dont work properly,when I brake the pedal goes all the way to the floor.Is my master cylinder the problem?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 2 Answers

Best place to start is looking for a leak in the system especially on corroded brake lines. fill master cylinder with fluid and have assistant gently push on brake pedal. check all fittings and lines for leaks. look carefully around gas tank as lines snake in front of tank above heat shield and are impossible to see without removing tank but leak will drip down at some point.

Posted on Jan 29, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BRAKES BLED PEDAL GOES TO FLOOR WHEN STARTED


if a master cylinder is bad and you are sure you have all the air out and no leaks.pedal will go to floor , running or not. if booster is bad it will cause a hard pedal. but if master cylinder is bad it will turn on a brake light on dash if it works. make sure the wheel cylinders are not leaking. I beleive that the master cylinder is bad, or you have a leak somewhere. If the master cylinder is functioning properly, the brake pedal will depress to a certain depth and no further.

Apr 20, 2012 | 2000 Chevrolet Blazer

2 Answers

Front and rear drum brakes, the pads are ok, but the brake pedal started going to the floor. When I tried to bleed them, the rear bleeder screws broke. So I replaced both wheel cylinders. The rubber...


OK........as you have stated that you have bled the brakes properly.....was there fluid coming out each bleed nipple as a flowing stream...????

And did you shut off the bleed nipple half way down stroke....?????

If this is all ok, then I would be looking at a failed master cylinder.......and what is occurring is the fluid is leaking from the primary to the secondary within the master cylinder !!!!!

Mar 31, 2011 | Ford Mustang Cars & Trucks

2 Answers

Brake pedal goes to the floor


possible leak in brake system. if not then you have a bad master cylinder. have to replace it.

Aug 30, 2010 | GMC K2500 Cars & Trucks

2 Answers

98 wrangler - brake pedal goes all the way to the floor. The master cylinder and all brake lines are free of leaks. I'm not losing any brake fluid anywhere. I replaced the booster that is attached to the...


You changed the master cylinder and vacuum booster and have no leaks anywhere, but did you bleed the entire brake system after you did this work? A little bit of air in any of the lines will make the brakes ineffective.

May 30, 2017 | 1998 Jeep Wrangler

3 Answers

While driving my 1994 Honda Accord the brakes went out. I can only get the car to stop if I press the brake pedal all the way down to the floor. When the car is shut off and I pump the brake pedal, I can...


There may be air in the lines. Bleed all your brakes starting at the farthest wheel from the resevoir, and finishing at the closest one. Try the pedal after its bled. If the pedal still feels soft or travels to the floor there may be a pinhole leak that may be spraying on the underbody of the car, or the seals in the master cylinder are gone filling the vacuum booster(if equipped). Air compresses more than oil so if bleeding works that may be the problem.

Feb 21, 2010 | 1994 Honda Accord

2 Answers

The brake pedal is fine with engine off. When started the pedal drops almost to the floor.Fluid level is fine, I have jacked up all 4 wheels and checked if the brakes are working- they are.....


the master cylinder has a bypassing issue. double check your rear brakes for proper adjustment and if good, replace the master cylinder and bleed the system. happy new year

Dec 31, 2009 | 1994 Honda Accord

1 Answer

Brakes


The brakes just need to be bled properly which take 2 people or a bleeding pump,Please tell me how you are bleeding the brakes.

May 17, 2009 | 1998 Audi A4

2 Answers

1973 F250 TRUCK 4X4 BRAKE PEDAL GOING TO THE FLOOR


Master is internally bypassing : replace or rebuild.

Feb 20, 2009 | 1989 Chevrolet K1500

Not finding what you are looking for?
1998 Dodge Stratus Logo

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...