Question about 2006 Nissan Altima

Open Question

I have a 2006 Nissan Note 1.4 SE, the heated door mirrors and rear window work on the same switch, but only the right door mirror is heating with the rear window, the left door is not heating at all. The reason why I am posting this on the 2006 Nissan Altima, is because I would imagine that Nissan would have used the same electrical components in both the Note and Altima to heat the rear window and door mirrors. Does anyone else have this problem? Any help would greatly be appreciated. Just I don't want to go and pull switches and mirrors apart, if that is not the problem . Thanks in advance for any help! :)

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: installing a Nissan Sentra Passenger Side Manual Non Folding Mirror.

had to install a driver side non folding mirror, fairly simply to say the least. There's a cover on the interior of the door, near the window, remove the cover, remove the 3 screws, need i believe a 10mm socket. If a power window, unhook the circuit. Replace new mirror.

Posted on Aug 25, 2008

SOURCE: 1994 Nissan Altima needs window switch replaced

take off the door panel and separate the plug

Posted on Aug 30, 2008

SUL827
  • 93 Answers

SOURCE: nissan murano 2204 rear view mirror installation

Adhesive is available @ most auto parts stores. I believe it is a Loctite product (or equivilent). Just ask a salesperson and they should be able to help you, good luck.

Posted on Sep 14, 2008

autodr
  • 260 Answers

SOURCE: 1993 electric windows stopped working on nissan altima

hard to say without testing, but the master window switches are common and will stop the rest of windows working, make sure window lock switch if off

Posted on Nov 15, 2008

  • 491 Answers

SOURCE: 1995 Nissan Altima, heat doesn't work.

you might want to replace your thermostat and start from there

Posted on Jan 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I lost the fuse diagram for my dads 95 dodge grand caravan. Can anyone help me out with one?


#1: Panel Illumination
#2: Guages,Right High beam headlight and the high beam indicator
#3: Rear Wiper, Left headlight High Beam
#4: RH park, backup lights switch and relay,Speed porpotional steering module,power door lock switch illumination and daytime running lights(Canada)
#5: Power Door locks,Power Mirrors,vanity,dome,map,ignition and trunk lights,sunroof,radio,power antenna,body control module and power for the data link connector
#6:Heated mirrors,heated rear window indicator
#7: Instrument cluster illumination,park and tail lights
#8: Cigarette lighter,Radio Amp and horns
#9: Power door lock motors
#10: Not used
#11: Radio
#12:Left low beam head light
#13,14,15,16 not used
26153814-2qh1jtrzfrcszgktlooiom5o-3-0.jpg

Apr 05, 2016 | Dodge Cars & Trucks

1 Answer

No indicators working found fuse box which fuse?


When you are talking about "indicators" we could assuming that your are refer about signal lights. This work with "flashers" devices.

For 1996 Audi A4 2.8L SFI 6cyl the Flasher is located in front seating area, driver side, under dash, behind dash lower panel, mounted above driver side of steering column.

About generic fuses, open the driver side door. Remove panel on left side of dash. Fuse box is behind panel:

Fuse # / Description / Amps
1 / Heated washer jets / 5
2 / Turn signals flasher unit / 10
3 / Headlight washer, illumination of glove compartment, engine compartment, climate control, automatic transmission, instrument cluster / 5
4 / License plate light / 5
5 / Instrument cluster, seat heating, test connection for cruise control, bulb monitor for auto-check control, Automatic transmission display, switch lighting, mirror switches and actuators, airbag warning light, outside temperature indicator, Climate control / 10
6 / Central locking system / 5
7 / Anti-lock brake system / 10
8 / Vacant
9 / Mirror heating / 10
10 / Vacant
11 / Cruise control (automatic transmission) / 5
12 / On board diagnostic system / 10
13 / Brake lights / 10
14 / Interior lights, reading lights, anti-theft alarm system, vanity mirror / 10
15 / Instrument cluster, power windows, climate control, automatic transmission / 10
16 / Anti-lock brake system, Anti-Slip-Regulation / 5
17 / Heated door locks / 10
18 / High beam right / 10
19 / High beam left / 10
20 / Low beam right / 15
21 / Low beam left / 15
22 / Tail and side marker right / 5
23 / Tail and side marker left / 5
24 / Wiper and washer system / 25
25 / Blower for heating, climate control / 30
26 / Rear window defogger, mirror heating / 30
27 / Rear window wiper / 15
28 / Fuel pump / 15
29 / Engine timing / 20
30 / Sun roof / 20
31 / Tail lights, cruise control, automatic transmission / 15
32 / Engine timing / 20
33 / Cigarette lighter / 15
34 / Engine timing / 15
35 / Trailer receptacle / 30
36 / Fog lights / 15
37 / Radio / 20
38 / Luggage compartment light, central locking system / 15
39 / Emergency flasher / 15
40 / Horn / 25
41 / Anti-lock brake system / 25
42 / Vacant
43 / Vacant
44 / Seat heating / 30

Hope this helps (remember to rate and comme this free answeer).



Jun 16, 2011 | 1996 Audi A4

1 Answer

Need the fuse panel layout for the panel by the passenger door [ just bought truck, panel cover missing. so we canttell which fuse runs what???



1994 Jeep Grand Cherokee Laredo
(Fuse Block - Passenger side of Dash)
1 5 9 13 17 21 25
20 A 15 A 20 A 20 A 7.5 A 15 A 30 A
2 6 10 14 18 22 26
15 A 15 A 10 A 20 A 15 A 15 A 30 A
3 7 11 15 19 23 27
20 A 15 A 15 A 3 A 15 A 15 A 10 A
4 8 12 16 20 24 28
15 A 15 A 15 A 20 A 10 A 7.5 A 30 A

1)Trailer Tow Relay 18)Airbag Module
2)Brake Lamps 19)Interior Mirror, Auto
3)Hazard Lamps Headlamps, Overhead
4)Security Lamp Console, VIC/GDM Module,
5)Interior Lighting Heated Rear Window Relay
6)Security Alarm Module Coil, Illuminated Entry Relay
7)Security Alarm Relay, and Chime Module
Security Alarm Module, 20)Heated Rear Window
Flash-to-Pass Switch, Overdrive Switch,
8)Overhead Console, Keyless Speed Control
Entry, Radio Memory/Clock 21)Security Alarm Module,
Memory/Chime Module, Lamp Outage Module
Power Locks, Power Mirrors, 22)Airbag Module,
HEVAC and VIC Speedometer, Tachometer,
9)Rear Wiper Telltales and Gauges
10)Radio 23)Heated Mirror Feed, Heated
11)Cigar Lighter Rear Window Switch
12)Parking Lamps, Automatic 24)Instrument Panel
Headlamps Illumination
13)Horn Relay 25)Power Seats
14)Power Lock Relays 26)Power Windows, Power
15)ABS Module and Relay Sunroof
16)Turn Signals 27)Security Alarm Module and
17)Heating and Air Front Wiper
Conditioning Module 28)Heated Rear Window Relay

Aug 20, 2010 | 1994 Jeep Grand Cherokee

3 Answers

2004 ford expedition eddie bower


For the rear window, just need adjuts the both slightly...


Check the next procedure to Power Mirrors...

Diagnosis & Testing

The exterior mirror control switch receives power through circuit SBP12 (GN/RD) and ground through circuit GD143 (BK/VT). The exterior mirror control switch uses circuit CPM23 (GY) as the common circuit for both exterior mirror up/down and right/left movement.
  1. Possible Causes:
    Fuse 12 (7.5A) (SJB) An open in circuits CPM23 (GY), SBP12 (GN/RD) or GD143 (BK/VT A short to ground in circuit CPM23 (GY) A short to voltage in circuit CPM23 (GY) Exterior mirror control switch.
  2. Checking the voltage at the mirror switch:
    Key in OFF position. Disconnect: Exterior Mirror Control Switch C527. Key in ON position. Measure the voltage between ground and exterior mirror control switch C527-1, circuit SBP12 (GN/RD). Voltage should be greater than 10 volts.
  3. If voltage is greater than 10 volts, check that fuse 12 (7.5A) is OK. If OK, REPAIR circuit SBP12 (GN/RD) for an open.

Exterior Mirror Motor Synchronization

NOTE This procedure must be performed any time the power folding mirrors are manually folded in or out, or if the position of the mirror case has been moved without using the mirror control switch.
NOTE If the power folding mirrors are folded or unfolded continuously (6 to 10 cycles), the power lockout feature will disable the system for 2 minutes to prevent damage to the power fold motors. After 2 minutes have elapsed, normal operation will resume.
  1. Set the mirror control switch to the CENTER position.
  2. Use the mirror control switch (press rearward) to automatically cycle the power folding mirrors in and out 4 times.
  3. When an audible popping sound is heard, the power folding mirror motors are synchronized.
    NOTE It may be necessary to cycle the power folding mirrors in or out up to 4 times before they are synchronized.

Removal & Installation
Motor
  1. Before servicing the vehicle, refer to the precautions section.
    NOTE If equipped with power folding mirrors, they must be synchronized any time the mirrors have been folded or unfolded without using the mirror control switch. Refer to synchronization procedure.
  2. Position the exterior mirror glass in a downward position to obtain a gap at the edge of the mirror.
    CAUTION Place a shop towel between the exterior mirror glass and the hand to avoid personal injury in the instance of glass breakage.
  3. Insert a flat-blade screwdriver between the mirror glass tabs and the mounting plate, and rotate to separate the locking tabs from the mounting plate.
  4. Carefully pull the top edge of the glass away from the exterior mirror housing.

    0996b43f802029e0.jpg Fig. Mirror Glass removal shown
  5. If equipped, disconnect the heated mirror electrical connectors and remove the glass.
  6. Remove the 3 exterior mirror motor screws and exterior mirror motor.
  7. Disconnect the electrical connectors.
  8. To install, reverse the removal procedure.

Switch
Expedition Trim Panel Removal

NOTE The door glass must be completely raised.
  1. Remove the window control switch plate.
  2. Remove the door handle bezel.
    WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  3. Remove the two bolts and three screws, and remove the door trim panel.
  4. Remove the finish cover to access the two center screws.
  5. Disconnect the electrical connectors. Navigator Trim Panel Removal
  6. Remove the door handle bezel.
  7. Use service notch.
    WARNING To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  8. Remove the two bolts and three screws, and remove the door trim panel.
  9. Disconnect the electrical connectors.
  10. Depress the locking tabs and remove the exterior mirror control switch.
  11. Remove the exterior mirror control switch.

If you dont want waiting more time for the Owners Manual, can check here this choice 2004-Ford-Expedition-Owners-Manual

Hope this help.

Apr 23, 2010 | 2004 Ford Expedition

2 Answers

Fuel Pump Fuse Number for a 1998 audi a4 2.8 quattro


Fuses: Fuse arrangement in fuse panel, behind instrument cluster, left
Fuse Arrangement In Fuse Panel 62624464

1 - Heated washer jets 5A 2 - Turn signals 10A 3 - Headlight washer (relay), illumination for glove
compartment, climate control, Automatic Transmission, instrument cluster 5A 4 - License plate light 5A 5 - Instrument cluster, seat heating, test connection
for cruise control, bulb monitor for auto-check display, Automatic Transmission display, switch
lighting, mirror switches and actuators, airbag
warning light, outside temperature indicator,
climate control 10A 6 - Central locking system 5A 7 - Anti-lock brake system (ABS) 10A 8 - Vacant 9 - Mirror heating 10A 10 - Vacant 11 - Cruise control (Automatic Transmission) 5A 12 - On board diagnostic system 10A 13 - Brake lights 10A 14 - Interior lights, reading lights, anti-theft alarm system, vanity mirror 10A 15 - Instrument cluster, power windows, climate control, automatic transmission 10A 16 - Anti-lock brake system (ABS), Anti-Slip Regulation (ASR) 5A 17 - Heated door locks 10A 18 - High-beam, right 10A 19 - High-beam, left 10A 20 - Low-beam, right 15A 21 - Low-beam, left 15A 22 - Side marker and tail light, right 5A 23 - Side marker and tail light, left 5A 24 - Wiper and washer system 25A 25 - Blower for heating, climate control 30A 26 - Rear window defogger, mirror heating 30A 27 - Rear window wiper 15A 28 - Fuel Pump 15A 29 - Engine timing 30A 30 - Sun roof 20A 31 - Tail lights, cruise control, automatic transmission 15A 32 - Engine timing 20A 33 - Cigarette lighter 15A 34 - Engine timing 15A 35 - Trailer recptacle 30A 36 - Fog lights 15A 37 - Radio 20A 38 - Luggage compartment light, central locking system 15A 39 - Emergency flasher system 15A 40 - Horn 25A 41 - Anti-lock brake system (ABS) 25A 42 - Vacant 43 - Vacant

Apr 05, 2010 | 1998 Audi A4

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

1 Answer

Ford expedition side mirror (instalation giude)


SECTION 501-09: Rear View Mirrors 2003 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Removal and Installation
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel —Expedition Removal and Installation
NOTE: Left front door shown, right front similar.
  1. Remove the door handle bezel.
    • Use service notch.
  1. Remove the window control switch plate.
    • Use service notch and disconnect the electrical connectors.
  1. s3j~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    Remove the two bolts and three screws, and remove the door trim panel.
  1. Remove the weather shield.
  1. Disconnect the exterior mirror electrical connector.
  1. Remove the exterior mirror.
    • Remove the nuts.
cf86471.gif
  1. To install, reverse the removal procedure.
    • Install top nut first.
---
Exterior Mirror Motor Removal and Installation
  1. Position the mirror glass to obtain a gap at the top edge of the mirror and carefully pull the top edge of the glass away from the mirror housing.
  1. Disconnect the heated mirror electrical connectors.
  1. Remove the exterior mirror motor screws and exterior mirror motor.
    • Disconnect the electrical connectors.
  1. To install, reverse the removal procedure.

Oct 26, 2009 | 2003 Ford Expedition

1 Answer

2006 GMC 3500 loss of power to drivers door


the main switch is wore out, Had the same problem the dealer install new switch 100 dollars for the part 125 for labor good luck

Jun 02, 2009 | 2006 GMC Sierra 3500

1 Answer

Side mirror of 2005 ford explorer


Exterior Mirror Removal and Installation
All vehicles
  1. NOTE: Left side exterior mirror shown, right side similar.
    Remove the interior door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel Removal and Installation
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the inside door handle bezel from the trim panel.
  1. Remove the window switch assembly.
  1. Disconnect the window switch and power door lock electrical connectors.
  1. Remove the upper trim panel screw at the window switch opening.
5c94a3e.gif
  1. Remove the lower trim panel screws.
2de1016.gif
  1. s2n~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the door trim panel, do not pull directly outward for this step.
    Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
  1. Disconnect the power mirror electrical connector.
  1. Remove the trim panel.
  1. Remove the weather shield.
Vehicles with power, heated or approach lamp equipped exterior mirrors
  1. Disconnect the electrical connector.
All vehicles
  1. Remove the bolts.
a2275a5.gif
  1. Remove the exterior rear view mirror (17682).

Feb 23, 2009 | 2003 Ford Explorer

1 Answer

Passenger side heated mirror not working on 2004 gmc yukon


i kind of dought there would be 1 fuse for one mirror if anything there be 1fuse for both mirrors. chances are what happend is this, they work like your rear window defroster on the rear window you see little wires that run across the window, same with mirror, the wire that heats them little wires most likely broke.

Jan 14, 2009 | 2004 GMC Yukon

Not finding what you are looking for?
2006 Nissan Altima Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...