Question about 1996 Ford Explorer

1 Answer

I have a 1996 Ford Taurus. Got a new battery (First I ever had to replace) after putting it in (same spec battery as the factory one I replaced) the Car alarm makes the Lights flash for about 1-2 mins after I start it... then it runs fine... No siren, no horn beeping... just lights flashing... How can I disable the factory alarm... it isnt worth stealing anyways... its a winter rat for my vette.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 38 Answers

To disable the alarm you must go to the specialised ford garage. They will hawe all the codes and equipment to fix that. You may want to stay away fromunqualified guys. They will charge you for the job, but the problem can come out again.

Posted on Jan 02, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Radio fuse blew, speedometer quit working. After replacing fuse the speedometer is very sluggish (goes up fast down slow)


You may need a new Vehicle Speed Sensor. It is located on the Transmission on the Passenger side out-put shaft housing.

Jan 03, 2014 | 1996 Ford Taurus

1 Answer

A/C compressor replacement


You will need to take it and have it put on a machine to have a vacuum drawn on it as thats how the system works. so they will set the pressures as per specs once you get it that far,

Jul 14, 2012 | 2004 Ford Taurus

1 Answer

I need the cheapest way to replace a key chain lock unlock switch for a 95 ford taurus


Hard to figure out what you are talking about. If you mean the remote which attaches to your keychain and unlocks the doors, then you can buy a used one on ebay for about 10 bucks, put a new battery in it, about 4 bucks, take it to a dealer and have them teach your car to recognize it, about 20 bucks or free depending on
your persuasive abilities.

Oct 27, 2010 | 1996 Ford Taurus

2 Answers

Whats easiest way to remove and replace engine in a 1996 ford taurus from the botom or out threw the top


depending on how your set-up makes all the difference. if you are doing it in the drive way out the top is the best. if you have a shop and a lift then top or bottom is almost the same. coming out the top is a little harder if you haven't do it before. so if you have a lift and equipment the bottom is best.

Oct 25, 2009 | 1996 Ford Taurus

2 Answers

1996 Ford Taurus has been having problems starting up


Get a new battery - I did and it works OK.
Make sure it is the high output type as used in Jeeps etc. Check spec book for it in shop.

Oct 14, 2009 | 1996 Ford Taurus

1 Answer

How to put a new one in


If you go to autozone.com, they have access to free repair manuals, you can print out step by step instructions from there. you will have to register with the sight and provide your vehicle information. it is free. this is for the 3.0 v-6 OHV (2-valve). you will need a couple of special tools, disconnect the battery neg (black) terminal remove the accessory drive belt remove the alternator remove and drain the coolant from the recovery reservoir put a drain pan under Pwr STR pump under the vehicle and disconnect the lines and let them drain remove the idler pulley remove the bracket mounting bolt under the belt tension mounting remove the 2 retaining nuts/ remove mounting studs/ remove Pwr Str Pump support w/ pump attached clamp pump in vise/remove pulley (special tool) remove three bolts on the support, remove Pwr Str pump.
replace as you have taken apart when installing you will need the second tool "pump pulley replacer" Good Luck!

Sep 13, 2009 | 1996 Ford Taurus

1 Answer

1999 Ford Taurus turns over but won't start


it probably has nothing to do with heat... it is probably a battery drain...need to put an ammeter inline to see if a drain... factory specs it at .05 amps draw or less.. let me know for more help

Sep 02, 2009 | 1999 Ford Taurus

1 Answer

Replacing wheel bearing in 1996 ford taurus


It probably needs to be pressed in & out. The hammer is only so good,lol. Make sure you tighten everything to spec too.

Jun 21, 2009 | 1996 Ford Taurus

1 Answer

1996 Ford Taurus GL with no spark I replaced ignition coil kit but it did not fix. Battery is fine and engine cranks over fine. What else can prevent spark if everything seems to have power?


Hello Johnrevival, Did you toss in new spark plugs too? I would suggest the best of champion which are designed specifically for ford engines.

Oct 31, 2008 | 1996 Ford Taurus

1 Answer

Dead battery.


Here is a link to the factory owners manual, the info about the fuse is in the manual.

http://www.motorcraftservice.com/pubs/content/~WO1TAU/~MUS~LEN/41/01tauog1e.pdf

Oct 11, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
1996 Ford Explorer Logo

410 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...