Question about Suzuki Sidekick

1 Answer

Clicking beside fuse box and by pressure regulator valve and wont start

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 38 Answers

Wery hard to tell from so short description, but it seems like it has problem with starter or the battery is to weak. First try to charge hte battery or better if you have other battery, wich is definetly in good working order. The grease in the starter with time is turning into a dirt and that can jamm your starter. Take of the starter, clean it and try to start again.

Posted on Jan 02, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vt commodore. I removed the engine cont fuse while doing a fuse check.. now my car wont start or do anything.. if you leave ignition on there is a contstant click from the box beside the fuse box


The clicking is probably coming from the starter solenoid. This probably needs to be replaced. Try putting car in gear and rocking back and forth a few times. Make sure ignition is off.

Jul 22, 2016 | Cars & Trucks

1 Answer

Astro troubleshooting over fueling ?


The pressure regulator is a diaphragm-operated relief valve with system operating pressure on one side and and atmospheric pressure on the other side. The function of the regulator is to maintain a constant pressure to the injectors at all times, by controlling the flow in the return line by means of a calibrated bypass. The pressure regulator on this unit is serviced as part of the fuel meter cover and should not be disassembled. The regulator is in your IAC valve. (Idol Air Control Valve) It is most likely stuck. Replace and watch the magic happen. Hope this helps.

May 20, 2014 | 1991 Chevrolet Astro Extended

1 Answer

My 2000 chevy S10 wont start I changed the battery and it ran fine for 2 days now it will turn over but won't start


Check Fuel Pressure. First turn key to on position (without starting) and listen for the fuel pump motor. If no motor sound, your fuel pump is not working. Check fuel pump fuse and relay. If fuel pump works, check for pressure at the fuel rail (schrader valve on fuel rail for pressure testing). If no pressure, or not enough, fuel filter might be clogged or fuel pressure regulator may not be working properly. IF fuel is not the problem, start checking electrical, such as ignition control and proper spark to plugs.

Aug 14, 2010 | 2000 Chevrolet S-10

2 Answers

My 96 blazer wont start it just cranks but wont start?


A typical engine needs mostly just gas and spark to run (besides air of course)
Sounds like the engine is not getting one or the other.

Fuel goes from fuel pump, to filter, to fuel pressure regulator, to fuel rail, to injectors.
You can test for fuel pressure with key on, at the fuel rail. There will be a test port on the rail that you can put a rag on top and push in the valve to see if there is pressure. (or use pressure tester)
If there is no pressure, check that fuel pump relay is working. (you can use an ohmmeter on relay to see if there is resistance). You can also test power to relay and to the pump with a voltmeter to see if pump is getting power. Or turn key to ON position and listen to see if you hear the pump turn on.

If you have no spark to any cylcinders, the crank shaft position sensor may be faulty which is very common in GM vehicles.

You can use an ohmmeter to test the sensor itself.
You can also get a spark plug tester to see if there is spark to each cylinder.
You can also remove one spark plug, plug back into plug wire, lay on top of engine so spark plug diode is 1/4" away from metal surface. Have someone else turn engine over while you look for spark. Do this to each cylinder.

Nov 16, 2009 | 1996 Chevrolet Blazer

2 Answers

Car wont start 2002 mustang gt dtc 1230 1233 codes , no bad fuses or relays, no fuel pressure at rails new pumps..


If you are not getting fuel pressure to the rails then you have an electrical problem such as a relay or fuse which are located in under hood fuse box, or the pressure regulator on the beginning of the fuel rail where the lines come in is bad.

Sep 13, 2009 | 2002 Ford Mustang

1 Answer

Eng light comes on idles wont rpm up backfires .


i would go to the air flow meter on a toyota start at the air box go to plenum then throttle body vacuum themn look at fuel injection go towards egr valve ..bad oxy sensors throw eng codes.

May 08, 2009 | 1994 Toyota Camry

1 Answer

Wont start it turns over but wont stay started


check the fuel pressure....there is a valve near the fuel pressure regulator that u can connect a fuel pressure guage to.under the hood on the right in the area of the brake master cylinder( right upper corner...( a line with a threaded valve)..check the reading and make sure they are in specs, i dont know the specs off hand but a service manual will help..if the pressure isnt in spec, replace the fuel pressure regulator..

Apr 07, 2009 | 1995 Honda Passport

3 Answers

2000 Chevy Venture Fuel Pressure Regulator


use the pressure test port on the top of the engine, it is on the fuel rail that supplies fuel to the injectors, looks like a tire valve, will have a plastic cap on it.

Mar 22, 2009 | 2000 Chevrolet Venture

1 Answer

2000 gmc jimmy wont start fuel pump comes on and cuts off but will not start.I have changed the fuel filter and that did not work. Is the pump not building the pressure it needs to start or would my...


the fuel pressure if leaking could cause this the regulator is located under the intake plenum but you should smell gas .if you dont then most likely the pump is bad ,the pump will come on for 2 seconds when the key is on then go off it will not stay on with just the key on only when you crank it will it .so have your fuel pressure checked with a gauge.

Mar 22, 2009 | 2000 GMC Jimmy

1 Answer

2000 gmc jimmy wont start fuel pump comes on and cuts off but will not start.I have changed the fuel filter and that did not work. Is the pump not building the pressure it needs to start or would my...


When you hook the pressure test guage to shrader valve on fuel rail what it reads is what the pressure is from pump, around 60 p.s.i. all you need to do is hook up the guage and turn on key, you do not have to turn engine over, and if pump is good it will shoot up to 58 or 60 right now.

Feb 14, 2009 | 1999 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...