Question about 1993 Mercury Villager

1 Answer

I need to let out all of the air from the hose on the radiator where can i find a valve to let it out. its on a 1993 mercury villager 3.0

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Http://groups.yahoo.com/group/villagerquest/

you just loosen the lower hose clamp and twist the hose and let it leak out there

gerry

Posted on Feb 07, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Mercury Villager keeps overheating. What else can it be or be done?


Exhaust Converter Blocked ?

Did you check for combustion gases at the
coolant or radiator fill

Your down to a head gasket or a crack somewhere

I would think the head gasket is common on that
motor possibly,research that

Timing Belt worn or jumped ?

Nov 18, 2014 | 2002 Mercury Villager

1 Answer

1997, Mercury Villager, NO HEAT. Flushed radiator, flushed heater core. Has a rear heating system, is there an additional heater core and maybe a valve in the rear heating system?


you have air trapped in system. If you could hang van like a deer in a tee, you could get the air out. Go to a sho with evac/fill equipment and have them purge the air. You are about 3 qts short of full

go here too. read cooling system files.

http://groups.yahoo.com/group/villagerquest/

Nov 27, 2010 | 1997 Mercury Villager

1 Answer

How do you bleed the radiator? on a 1999 merc villager


With all cars the radiator has to be bled.
In most cases it just involves filling the reservoir and radiator, and squeezing the hoses until all the air bubbles out that you can get, and then cycling the car by running it until hot, shutting it off and letting it cool, and repeating that a few times.
Each time it gets hot it will burp out some air and replace it with water from the reservoir.

But some cars trap too much air, so also have a valve on the engine that can be opened up. Cars with the engine far from the radiator even require having the car tilted on a lift, towards the filler. Adding a water hose connection T fitting to the heater hose is also always a good idea. Not only is it good for back flushing, but for bleeding as well.

Aug 12, 2010 | 1999 Mercury Villager

1 Answer

I need firing order of piston on a 3.0 in a 1993 mercury villager


For the 1993 Mercury Villager 3.0L V6:

Firing Order:
1-2-3-4-5-6

Cylinders:
......(back)......
|...1....3....5...|
.......................
|...2....4....6...|
......(front)

Distributor:
..(back)
.....2
3........1
4........6
.....5
(front)

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

May 29, 2010 | 1994 Mercury Villager

2 Answers

My 1999 mercury villager ac works in the front but no cold air blows in the back. What needs to be fixed?


it needs to have the rear expansion valve to be inspected for metal, if clean repl expansion valve and recharge a/c

May 20, 2010 | 1999 Mercury Villager

1 Answer

Where is the thermostat located at in the engine compartment of the 2000 mercury villager


passenger side (rt) of engine, middle. Be ery careful tightening the bolts so you don't break the pipe. Locate thermostat with jiggle valve facing up.

It is very hard to bleed air from system when refilling. see files if you don't have heat when done.

go here too

http://groups.yahoo.com/group/villagerquest/

Housing Removal
  1. Drain the cooling system; refer to Cooling System Draining, Filling And Bleeding .
  1. Remove the upper radiator hose.
    1. Remove the hose clamp bolt.
    1. Remove the hose clamps.
    1. Remove the upper radiator hose.
  1. Remove the water bypass hose.
    1. Remove the clamps.
    1. Remove the bypass hose.
  1. Remove the thermostat housing.
    1. Remove the bolts.
    1. Remove the thermostat housing.
Installation
  1. syv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not reuse hose clamps. Make sure new hose clamps are seated correctly.
    NOTE: Make sure the thermostat housing and mating surface are clean of dirt and old silicone.
    NOTE: Apply a 2.0-3.0 mm (0.079-0.118 inch) bead of Silicone Gasket and Sealant F7AZ-19554-EA or equivalent meeting Ford specification WSK-M2G343-A4 to the mounting surface of the water pump.
1dc227b.gif

Jan 09, 2010 | 2000 Mercury Villager

2 Answers

I have a 2001 mercury villager that overheats. I replaced the fan assembly and the thermostat. The radiator is fine. What else could be causing the van to overheat?


You have air trapped in the system. If you have cold air, warm air, cold air from your heater, then it's air entrapment. Very common these days. Go to a shop that uses vacuum method to refill cooling system & that will purge air.
Otherwise, you can try. Park uphill. cold engine - fill radiator to top with 50/50 mix of antifreeze. leave cap on but loose. fill reservior to 3/4 full. Turn heater to hot to allow coolant to flow through heater core. start engine, run at 1500 rpms until thermostat opens and upper hose is hot. tighten cap and let it cool down. after cool check level of reservoir. fill to top line on reservoir. it should **** coolant back into radiator as it cools down.
repeat if still an issue.

go to yahoo group for villager quest & join owner group for much more help. 2500 members.

Dec 07, 2009 | 2002 Mercury Villager

1 Answer

Overheating


you have air trapped in the system. very hard to "BURP AIR"

park uphill on ramps if possible. With cold engine, leave radiator cap loose and fill radiator and reservoir. run engine until thermostat opens. squeeze upper radiator hose with hand. SHould be hot. Have heater on hot and blower on too. Repeat as necessary. May take several attempts.

Go here and we can help if that does not work

http://autos.groups.yahoo.com/group/villagerquest/

May 02, 2009 | 2002 Mercury Villager

1 Answer

Mercury villager brakes drag when driving


replace the flexible hoses, they are collapsing inside, preventing fluid from returning to reservoir.

go to this site for villager hep

http://autos.groups.yahoo.com/group/villagerquest/

Apr 06, 2009 | 1993 Mercury Villager

2 Answers

No heat


if you replaced the thermostat, you have an air bubble trapped in the engine. So, you don't have any coolant running through the heater core, therefore no heat.
sometimes hard to "burp" air bubble. Try this. Park park facing uphill and jack up front of car too. You want to get radiator opening higher than top of engine. Then remvoe radiator cap (cold engine), fill radiator, then fill coolant reservoir to full point. Install radiator cap but leave it loose so air can escape. Start engine until upper radiator hose going into radiator is hot. This should burp air. Repeat a few times while adding coolant mix (50/50 antifreeze) to keep radiator full. Be careful not to remove radiator cap when engine is hot.
lwt us know how ou make out. There is a more complicated procedure but you need tools and knowledge of where air bleed is on top of engine

Jan 03, 2009 | 1998 Mercury Villager

Not finding what you are looking for?
1993 Mercury Villager Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...