Question about 1991 Toyota Previa

Open Question

Remove and replace 1991 previa differential 2WD

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 67 Answers

SOURCE: 1991 Previa Van Rear Differential going bad

Oil loss, from where? Dropping from centre, or out through axles/ brakes? Obviously too late to reclaim, diffs are not an item you can repair yourself, best ask a specialist for opinion/ price to replace/ repair centre. Oil loss should not happen, can drop from centre via poor gasket or seal at input, or axle seals.
For a do- it- yourself type fix, a wrecker might supply a complete unit or centre section, but as you appear to have little knowledge of mechanicals, I'd say leave it to the experts!

Posted on May 16, 2008

Ad
mickha2
  • 145 Answers

SOURCE: How to replace dash light bulb of 1991 Toyota Previa Van

pop fuse cover, remove vent housing, remove speedo upper cover, remove 4 bolts holding speedo remove speedo, change bulb

Posted on Aug 17, 2010

  • 14585 Answers

SOURCE: I have a 91 toyota previa and im trying to remove

Most differentials are set up like this. There is a steel bar that is i the middle of the gears, this is held in with a bolt. remove the bolt. pull the bar out. Then push the axles in the center. There is a c clip to remove from the axle. They will come out easily. Pull the axles out. Once the axles are out the hog head as they call it, will come out. Just watch as the inner gears will come out also. And will have to be placed in the same spot. Kinda of push in and see. let me know

Posted on Aug 17, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove egr valve on a 1993 toyota previa


That previa has a central engine, so all engine work requires you take out driver and or front passenger seat out.

The EGR placement is here >> http://www.autozone.com/autozone/repairguides/Toyota-Previa-1991-1997-Repair-Information/EMISSION-CONTROLS/Exhaust-Gas-Recirculation-System/_/P-0900c1528008a1d5

near the bottom of the page.
Good luck

May 13, 2014 | 1993 Toyota Previa

1 Answer

1991 toyota previa van won't start sometimes and cuts off by it self sometimes was told not the fuel pump but the computer.What kind of computer needs to be replace to fix that?


probably the main one. did you try the map sensor. my dad had one that he spent alot of money on and come to find out it was a $26 map sensor that plugs in on top of the motor.

Jan 20, 2013 | 1991 Toyota Previa

1 Answer

I have a 91 toyota previa and im trying to remove the rear differential..its a 2wd. I have unbolted the drive axle and the differential casing but its my understanding you have to pull lose the rear...


Most differentials are set up like this. There is a steel bar that is i the middle of the gears, this is held in with a bolt. remove the bolt. pull the bar out. Then push the axles in the center. There is a c clip to remove from the axle. They will come out easily. Pull the axles out. Once the axles are out the hog head as they call it, will come out. Just watch as the inner gears will come out also. And will have to be placed in the same spot. Kinda of push in and see. let me know

Aug 16, 2011 | 1991 Toyota Previa

1 Answer

How to replace dash light bulb of 1991 Toyota Previa van


pop fuse cover, remove vent housing, remove speedo upper cover, remove 4 bolts holding speedo remove speedo, change bulb

Mar 31, 2010 | 1991 Toyota Previa

2 Answers

How do I remove and replace a starter from a 1993 Toyota Previa? I am told it's rather difficult and may include removing something from the automatic transmission.


Removal & Installation
  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front drive shaft.
  4. Remove the nut and disconnect the starter wire.
  5. Disconnect the starter connector.
  6. Remove the bolt holding the starter stay to the upper stiffener plate.
  7. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  8. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
To install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts.
  2. If equipped with 2WD, install the starter, nut and three bolts.
  3. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  4. Install the starter connector.
  5. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  6. If equipped with 4WD, install the front drive shaft.
  7. Connect the negative battery cable.
Good luck and this should take about 2 1/5 hours from start to finish and if you like, use lock tight medium strength to make sure the bolts don't go lose on you.

Nov 04, 2009 | 1991 Toyota Previa

1 Answer

LOUD NOISE FROM REAREND


remove the the diff unit and refit into your casing ,,,easy job,Preload on pinion bearings and set crownwheel backlash to a very small wiggle woggle.handful of LM grease in unit before you refit cover then use ep90 gear oil .job done shouldnt take more than a morning to do.

Dec 23, 2008 | 1991 Toyota Previa

1 Answer

Starter replacement - 1991 Toyota previa


Here are detailed, step-by-step instructions for the removal and re-installation of your starter motor. Hope this helps! Have a great day!

Starter Toyota Previa 1991-1997 Repair InformationREMOVAL & INSTALLATION
See Figures 5 through 12
  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front driveshaft.
  4. Remove the nut and disconnect the starter wire.
0900c15280089fbb.jpgFig. 5: Disengage the starter wiring
  1. Disconnect the starter connector.
0900c15280089fbc.jpgFig. 6: Remove the cap hiding the nut 0900c15280089fbd.jpgFig. 7: It will be necessary to use an extension to remove the nut
  1. Remove the bolt holding the starter stay to the upper stiffener plate.
  2. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  3. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
0900c15280089fbe.jpgFig. 8: Four bolts hold the starter in place 0900c15280089fbf.jpgFig. 9: The nut is located on the top of the starter 0900c15280089fc0.jpgFig. 10: Extract the starter from the engineTo install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc1.jpgFig. 11: Bolt locations on the 2WD models
  1. If equipped with 2WD, install the starter, nut and three bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc2.jpgFig. 12: Bolt locations on the 4WD models
  1. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  2. Install the starter connector.
  3. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  4. If equipped with 4WD, install the front driveshaft.
  5. Connect the negative battery cable.
SOLENOID REPLACEMENT
The starter solenoid (magnetic switch) is an integral part of the starter assembly.
  1. Remove the starter from the van. Remove the heat insulator from the starter assembly, if equipped.
  2. Disconnect the wire lead from the magnetic switch terminal.
  3. Remove the two long, through bolts holding the field frame to the magnetic switch. Pull out the field frame with the armature from the magnetic switch.
  4. Toseparate the starter housing from the magnetic switch assembly, remove the two screws and the starter housing with the pinion gear (1.6 kW), idler and clutch assembly.
To install:
  1. If necessary, install the gears and clutch assembly to the starter housing. Apply grease to the gear and clutch assemblies and place the clutch assembly, idler gear, bearing and pinion gear (1.6 kW) in the starter housing.
  2. Insert the spring into the clutch shaft hole and place the starter housing onto the magnetic switch. Install the two screws.
  3. Install the field frame with the armature onto the magnetic switch assembly and install the two through bolts. Tighten the bolts on the 1.4 kW to 52 inch lbs. (6 Nm) and on the 1.6 kW to 82 inch lbs. (9 Nm).
There is a protrusion or tab on each part; make sure you line them up correctly during assembly.
  1. Connect the wire to the terminal on the magnetic switch and tighten the nut to 52 inch lbs. (6 Nm). Install the heat insulator, if equipped.
  2. Reinstall the starter on the vehicle. Check starter system for proper operation.

Nov 23, 2008 | 1991 Toyota Previa

1 Answer

Toyota Previa GS 2000 - vibration through the steering wheel at high speeds


Did you have to remove front drive shaft to replace stabilzer link bars?

Aug 10, 2008 | 1991 Toyota Previa

2 Answers

1991 Previa Van Rear Differential going bad


Oil loss, from where? Dropping from centre, or out through axles/ brakes? Obviously too late to reclaim, diffs are not an item you can repair yourself, best ask a specialist for opinion/ price to replace/ repair centre. Oil loss should not happen, can drop from centre via poor gasket or seal at input, or axle seals.
For a do- it- yourself type fix, a wrecker might supply a complete unit or centre section, but as you appear to have little knowledge of mechanicals, I'd say leave it to the experts!

May 14, 2008 | 1997 Toyota Previa

Not finding what you are looking for?
1991 Toyota Previa Logo

Related Topics:

258 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...