Question about Toyota Camry

1 Answer

'87 Toy Camry wagon; My washer pumps don't run, wipers do. Started to replace pump, but found no voltage there in ACC mode with buttons pressed, while the wipers work. Is there a relay? Also, my digital clock is dead, and the battery drains down in 2 weeks nonuse. Thanks, Tom

Posted by on

  • tetech2 Jan 04, 2011

    The pump died first before the clock. Not sure where the fuse box is under dash, my manual says the clock and cig lighter are on same fuse. I'll have my sister check if the 12v is there (she took the car today for her son, I won't see it till Feb). Is there relays for the washers or just the pushbutton switches?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Expert
  • 4,070 Answers

Hi and welcome to FixYa!

As a first course of action please replace the dead battery. Please check the fuse underneath the dash and look for the clock fuse. The clock and washer fuse can be interconnected that's why it failed at the same time.

Hope this helps and thank you for using FixYa! Have a good one!

Posted on Jan 01, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Pontiac Montana wipers not working how to fix


First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

Nov 25, 2016 | 2003 Pontiac Montana

1 Answer

In my 2007 Saturn Vue there is what I think is an air pump which is cracked that one port is not connected to anything.


There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

Nov 18, 2016 | Saturn Cars & Trucks

1 Answer

Cadillac Deville 99


Wiper/Washer System (Pulse) Schematics (w/o CE1)
Wiper/Washer System (Pulse) Schematics (w/CE1)

Which one does yours have ?

The switch could be bad or the windshield wiper / washer module . Do you own a DVOM - digital volt ohm meter ? Do you know how to do automotive electrical trouble shooting ? There are a few good videos on youtube on basic electrical trouble shooting an how to read wiring diagrams . Go to http://www.bbbind.com/free_tsb.html for free wiring diagrams . Check B+ voltage at the switch (in an out ) at the different speeds .Check for B+ voltage at the wiper washer module , it's part of the wiper motor .
The windshield wiper/washer system consists of a permanent-magnet depressed-park wiper motor assembly, a wiper transmission assembly, wiper arm and blade assemblies, a washer pump mounted on a washer solvent container, and a wiper/washer switch assembly.
The wiper/washer system is a pulse (delay) type. Pulse timing and demand wash functions are controlled electronically. Wiper/Washer System Description (Rainsense)
The windshield wiper/washer system consists of a Rainsense module, a permanent-magnet, depressed-park wiper motor assembly, a wiper transmission, wiper arm and blade assemblies, a washer pump mounted on a washer solvent reservoir, and a wiper/washer switch assembly.
The wiper/washer system is a rain sensing type. Rainsense functions are controlled electronically. 1
Was the Wiper/Washer System Check performed?
--
Go to Step 2
Go to Wiper/Washer System Check

2
Inspect the WIPERS fuse A9 for an open.
Is the fuse open?
--
YES - Go to Step 3
NO - Go to Step 4

3
Replace the WIPERS fuse.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

4
Disconnect the wiper/washer switch connector C202.
Turn ignition switch ON.
Connect a test light from connector C202, terminal E5 to ground.
Is the test light on?
--
YES - Go to Step 16
NO - Go to Step 5

5
Connect a test light from Accessory Relay, terminal A1, to ground.
Is the test light on?
--
YES - Go to Step 6
NO - Go to Step 11

6
Connect a test light from Accessory Relay, terminal A3, to ground.
Is the test light on?
--
YES - Go to Step 7
NO - Go to Step 12

7
Connect a test light from Accessory Relay, terminal B1 to terminal A3.
Is the test light on?
--
YES - Go to Step 8
NO - Go to Step 15

8
Inspect CKT 143 for an open or poor connection between connector C202 and the Accessory Relay.
Was an open or poor connection found?
--
YES - Go to Step 9
NO - Go to Step 10

9
Repair the open or poor connection in CKT 143.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

10
Replace the the Accessory Relay.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

11
Repair the open in CKT 1040 or the power feed circuit to the WIPERS fuse.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

12
Inspect the ACC fuse C13 for an open.

let me know if you make it this far an then I will send the rest of testing procedures !

Mar 09, 2016 | Cadillac DeVille Cars & Trucks

1 Answer

Windshield washer pump works when the key is in acc and don't work when the engine is running,, grand am 2005.. is the ignition switch the problem? ,, thanks,,


Check for voltage at the wiper fuse, engine running. Use a testlite to for voltage. If the fuse circuit is hot, it's not the ignition switch.
That fuse circuit goes hot in acc or run.
I just glanced at the wiring diagram.

Dec 10, 2015 | Cars & Trucks

1 Answer

How do i get to the washer pump on a 1994 toyota camry?


I don't think any Camrys that year had rain sensing wipers so you could be right. Anyway to get at the pump you have to unscrew fixings and lift up the washer reservoir to disconnect the wiring, then remove the reservoir.

Jun 15, 2017 | 1994 Toyota Camry

1 Answer

Trying to find were the safety fuel cut off switch is located on a 1987 grand wagoner


I have the 87 cherokee and I don't think it has the "tip over" fuel cut off safety switch. If you are not getting any fuel the fuel pump (its in the fuel tank) has either lost power or stopped working. They used a couple of different styles so don't buy one untill you have pulled the old one out. also you can check for voltage on the wires that feed the fuel pump. If you have voltage but are not getting any gas flow then the pump is not working.

Apr 21, 2011 | 1987 Jeep Cherokee

2 Answers

2006 chevy impala windshield wiper fluid will not work. It's not frozen, and the tank is full. Do I need a new pump, and if so where is the pump located?


I just fixed the wifes 2006 Impala, windshild washer. If you look at the manual, under the hood fuse panel, you will find two fused identified as windshild wiper. The one at the bottom is the washer pump. They even conviently provide a spare (10 amp) fuse just below it. swap out and ops check okay. Hope this helps.
SundogKB

Jan 18, 2010 | Chevrolet Impala Cars & Trucks

2 Answers

I need help finding schematics for 1985 ford f150-302 6-cylinder fusebox.my wiper washer pump is'nt working and i don't have the owners manual.


The washer pump is on the same circuit as the wiper motor.If the wiper motor is working,then check the voltage,with a test light(purchase at the parts store cheap).When pushing the button to activate the washer,the test light should light up ,when touching the wire on the pump.and have the clip on the test light on a good ground on the vehicle.If it lights up,replace the washer pump,if it does not light up,replace the washer pump button.

Dec 05, 2009 | 1985 Ford F150

1 Answer

99 Nissan Quest real wiper runs continually when ignition is on


Principles of Operation
Operation of the windshield wiper and washer is controlled by the front wiper/washer amplifier assembly. The front wiper/washer amplifier input comes from the multifunction switch by means of a voltage divider circuit. A constant voltage is applied to the multifunction switch by the front wiper/washer amplifier. When the multifunction switch is moved into the LO, HI, or intermittent position, the voltage is directed through a series of resistors. This results in various voltages being returned to the module for each switch position. The module then grounds the appropriate circuit, based on the voltage signal received back from the multifunction switch. This causes the wipers to run intermittently, or at the appropriate speed. Voltage is supplied to the wiper motor by the CJB fuse F46 (20A).
When the multifunction switch wash button is depressed, it bypasses all of the resistors returning a full voltage signal to the module. The module then grounds the appropriate circuits to operate the windshield washer pump for as long as the switch is depressed. The windshield wiper speed is dependent on the position of the windshield wiper/washer switch.
Voltage for the windshield washer pump is also provided by CJB fuse F46 (20A).
Operation of the rear wiper and washer is controlled by the rear wiper/washer switch.
Voltage is supplied to the rear window wiper motor by the fuse junction panel fuse F44 (10A).
The rear window wiper motor ground is made or broken by the rear wiper/washer switch. When the rear wiper/washer switch is moved into the WIPER position, it grounds the rear window wiper motor circuit, causing the rear window wiper motor to run once every 10-15 seconds.
Voltage to the rear washer pump motor is also supplied by the CJB fuse F44 (10A). The rear washer pump is directly controlled by the rear wiper/washer switch which makes or breaks the ground for the washer pump motor, depending upon its position.
If the vehicle is equipped with a movable liftgate glass, a liftgate glass switch is utilized to prevent rear window wiper operation when the liftgate glass is open. This same switch also causes the rear window wiper to drop down approximately three inches when the liftgate glass latch is released.
------------------------------------------------------------------------------------------
  • The wipers stay on continuously — rear wiper
  • Circuit.
  • Rear wiper/washer switch.
  • GO to Pinpoint Test L .


---------------------------------------------------------------------------------------------
Measure the resistance between rear wiper/washer switch C288 pin 6, component side and rear wiper/washer switch C288 pin 2, component side.
  • Is the resistance less than 5 ohms with the switch depressed, and greater than 10,000 ohms with it released?
sxv~us~en~file=arrow.gif~gen~ref.gifYes GO to L2 .
sxv~us~en~file=arrow.gif~gen~ref.gifNo INSTALL a new rear wiper/washer switch. TEST the system for normal operation.

Measure the resistance between rear wiper/washer switch C288 pin 6, circuit WB08 (BU/YE), harness side and ground.
  • Is the resistance greater than 10,000 ohms?
sxv~us~en~file=arrow.gif~gen~ref.gifYes INSTALL a new rear wiper /washer switch. TEST the system for normal operation.
sxv~us~en~file=arrow.gif~gen~ref.gifNo REPAIR circuit WB08 (BU/YE). TEST the system for normal operation.

65501dd.gif 7e9d21a.gif

Dec 08, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...