Question about 1994 Ford F350 Crew Cab

1 Answer

My low beams don't work, but the high beams do. changed the light bulbs and headlight switch.

Posted by on

  • Miller
    Miller Jan 25, 2013

    I have the same problem on my 02 F350. Im curious, did you end up replacing the multifunction switch connector or the switch or both?Mine is all black at the connector and the two wires that control the hi/lo lamps get really warm. Not really looking forward to doing it.....

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 62 Answers

The multifunction switch that controls the wiper /turn signals,and high/low beam lights are very common for (when they get a lot of miles on them) for having problems.also I have seen a good number of these pickups that the connector (that plugs into the back of the multifunction switch)had lost the ability to properly hold the wire terminals into the connector causing a poor connection between the switch and the wiring. sometimes this can be verified without removing the column shrouds by (if equipped) tilting the tilt wheel up and down and see if the lights start working . hope this helps,thanks for using fixya

Posted on Jan 01, 2011

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 24 Answers

SOURCE: Low Bean Lights Inoperative on 1997 Acura TL

there should be a fuse and/or relay that operates the low beams, or try replacing the bulbs.

Posted on Feb 04, 2009

  • 1861 Answers

SOURCE: Low beam headlights don't work

I have e-mailed you 2 .pdf files, one is the complete headlamp diagram, and the other is the relay locations. Please advise if you need further assistance.

Toyota Ed

Posted on Jan 02, 2009

djicenova
  • 319 Answers

SOURCE: low beam headlights not working

check voltage at switch

Posted on Mar 18, 2009

  • 12 Answers

SOURCE: high beam headlight does not work properly

it more then likey a lose wire or bear one. run the line down. i think that the high beams run on diff. fuses. you can try that!

Posted on Jul 13, 2009

  • 8 Answers

SOURCE: low beam headlights do not work

replace low beam bulbs, you tend to use these more than high beams and it is not uncommon for them to quit a same time. It happened on my camaro and on a friends trans am. I bought a 50.00 headlight switch only to find out it was both low beam headlights, which on a 1997 camaro is another 50.00 (25.00 each). I would try that before taking dah apart. Added note, at first I had ruled out the headlamp being bad, because i had just replaced one of them 3 months before this happened. I pulled in the driveway they worked, when I was ready to leave I only had high beam, but problem was solved with 2 new headlights.

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevy Venture 99 low beams don't work but high beams always working


I would start with checking the headlight bulbs (slim to none possibility but starting point) next go to the headlight switch.

Aug 09, 2017 | Chevrolet Cars & Trucks

1 Answer

Low beam headlight drivers side don`t work. high beam it works.


Check tour bulbs first and replace if blown. If OK then check wiring backwards from light to dip switch.

Oct 05, 2012 | 1996 Ford Explorer

1 Answer

High beam headlights don't work, changed the bulbs, and checked the fuses, help


This is going to be a problem with your light switch or dimmer switch. Replace the light switch and see if that resolves the issue.

Nov 27, 2011 | 2002 Chevrolet TrailBlazer

1 Answer

Have a Nissan pathfinder 2005... The high beams don't wonk. I changed the bulbs and they still don't function.. Any idea how to fix this problem?


Did you check the relays? or the High beam switch? Usually you can trace the wiring down from the switch to a harness at bottom of steering column use test light there too.Use a Test Light at the headlight connection make sure that you have power Low beam then test high beam. If you can't figure out use of Test light, it has a ground clip and a probe (Sharp end)Ground the clip on something metal (on car) use the probe to touch wire (one at a time) in the socket where the headlight connections. 1 wire is ground 1 is LOW beam and other is HIGH beam. may need a mechanic to check the switch. The light on the tester will light up IF you have 12 volts. NO LIGHT NO POWER!

Oct 30, 2011 | Cars & Trucks

3 Answers

Low beam head lights not working - The low beams, both stopped working. The high beams work fine. I checked the fuses and all 4 are good. I even swapped the low and high beam fises just in case. No...


if the fuses are good then you need to check for power and ground at the headlight plug that attaches to the headlight bulb if you have a good power and ground there and the connections are good then the bulbs are both no good.or if you can tell the bulbs are burnt out by looking at them then you don`t have to check powers and grounds.you also can directly feed power and ground to the bulb and check both the terminals for high beam and low beam as you cannot tell which is which by looking at the terminals

Mar 04, 2011 | 2001 Ford Focus

1 Answer

Headlights


The same bulb in a lot of applications controls both the high and low beam. Generally the low beam portion will burn out and for a short time you will be able to use the high beam only. I can't be certain which headlight switch that you checked, but the most common solution is to replace the headlight bulb. The bulb is on the inside of the headlight lense and is accessible by opening the hood and peeling back the rubber cover that covers up all of the headlamp apparatus. Depending on the model of vehicle they are mounted in there differently. Make sure and change both at the same time. It is generally cheaper to purchase new headlight bulbs as a (2) pack and it never fails if you change one the other will burn out in a week. Hope this helps

Feb 15, 2009 | 1997 Chevrolet Cavalier

3 Answers

My head lights only work on high beam. if i switch to low they will cut off. all of my dash lights work regardless. any ideas of what may be causing it???


It is entirely possible for both low beams to be out have you verified that there is No voltage on the low beam electrical circuit of the headlights?

Aug 13, 2008 | 2001 Toyota Tacoma

Not finding what you are looking for?
1994 Ford F350 Crew Cab Logo

521 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...