Question about 2000 Dodge Durango

Open Question

I have a 2001 Dodge Ram 4x4 w/ 5.9l engine. It has the 46 RE transmission. I am getting the eroor code P1740. It says its either the TCC or the O/D solenoid. My question is (since there is little useful info in the Chiltons manual), Do I have to pull the transmission to replace either of these? From what little info I have found, the TCC is behind the drain pan but not sure of the O/D solenoid. I have never had any problems with the transmission before. The filter was replaced about 30,000 miles ago. There is a TSB out on this problem ( TSB 21-11-00). But I have have bad luck with local dealership.

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Trouble code P1740 on 1999 Dodge Ram 2500

I had the same code on my 2001 dodge 2500. The truck wouldn't shift from 3-4. I pulled the trans pan off and replaced a broken spring ($2.00). It is behind a thin plate with 3-4 small torq screws. You don't have to remove the valvebody. Only took me 45 minutes to fix.

I would like to give thanks to Jeff Russel from Teal automotive. He said this is a very common problem. He sells any part for any automatic Transmision and his prices are very affordable.
Here is a link to the website.
http://www.tealautomotiveinc.com/

Hope this helps.

Posted on Jul 19, 2009

ZJLimited
  • 17970 Answers

SOURCE: My 2007 dodge with 5.9

Code P1740-Torque converter clutch did not lock up when the PCM sent the command. Enabling conditions: No engine or transmissions codes are present, vehicle speed was under 70 MPH, TPS was under 33% open. When the PCM commanded the torque converter to lock, no change was detected in engine speed. Blocking action: This code can block the following monitors: none.

Testing: Check torque converter solenoid for proper operation.

NUMBER: 21-11-00
GROUP: Transmissions
EFFECTIVE DATE: October 02, 2000
SUBJECT: 46RE Transmission MIL Due To DTC P1740 - TCC or OD Solenoid Performance
OVERVIEW: This bulletin involves the replacement of the transmission pressure boost valve cover plate.
MODELS: 2000 - 2001 (AB) Ram Van 2000 - 2001 (AN) Dakota 2000 - 2001 (BR/BE) Ram Truck 2000 - 2001 (DN) Durango

NOTE: THIS BULLETIN APPLIES TO VEHICLES EQUIPPED WITH A 46RE TRANSMISSION BUILT BEFORE AUGUST 01, 2000 (MDH O8O1XX).

SYMPTOM/CONDITION:
The customer may complain of a Malfunction Indicator Lamp (MIL) illumination. Upon further analysis, it is determined that the MIL is caused by Diagnostic Trouble Code (DTC) P1740 - Torque Converter Clutch (TCC) or overdrive solenoid Performance. Other than the MIL, the customer may not notice any other condition with the transmission.

This condition may be caused by an intermittent and momentary TCC disengagement condition. The transmission valve body pressure boost valve cover plate has been revised with a larger size orifice hole to address this condition.

NOTE: THE DRB III(R) MUST BE OPERATING AT RELEASE LEVEL 50.4 MDS2 SYSTEM CIS CD2067 OR HIGHER (AVAILABLE THE WEEK OF OCTOBER 2, 2000) IN ORDER TO PERFORM THE REVISED TORQUE CONVERTER CLUTCH STALL TEST. DO NOT USE EARLIER VERSION STALL TEST TO DETERMINE CONDITION OF THE TORQUE CONVERTER CLUTCH.

Here can find the test in pdf format: 2009-11-28_034958_1124.pdf

Hope helps.

Posted on Apr 28, 2011

bonedivers
  • 1140 Answers

SOURCE: p1740 code on 2001 ram

there is a total of 27 diagnostic steps to follow, but here is some info for you:
SYMPTOM
P1740-TCC O/D SOL PERFORMANCE

WHEN MONITORED
The Torque Convertor Clutch (TCC) and Overdrive Clutch (O/D) will be tested each time the PCM requests TCC engagement in 3rd gear and O/D.

SET CONDITION
The code will set if the expected RPM drop is not achieved while attempting to engage TCC or O/D. This indicates a malfunctioning torque convertor or overdrive clutch.

POSSIBLE CAUSES
- Camshaft DTC present
- Engine RPM DTC present
- Fuel level low
- Misfire DTC present
- Output speed DTC present
- P1765 DTC present
- Park/Neutral DTC present
- PTO engaged (if equipped)
- Torque converter clutch DTC present
- TPS DTC present
- Transfer case in low range (if equipped)
- Transmission Relay DTC present
- Transmission temperature too cold
- Intermittent
- Check transmission fluid-debris
- Check transmission fluid-stall
- 3-4 Shift Solenoid
- Oil Pan contains excessive debris
- Shaft or seal damage
- TCC solenoid
- Torque converter
var classElements = new Array(); var node = document; var tag = 'a'; var els = node.getElementsByTagName(tag); var elsLen = els.length; var pattern = new RegExp("(^'\\s)specs_note(\\s'$)"); for (i = 0, j = 0; i

Posted on Jun 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 dodge ram 1500, V8 with a obdll code of P1740. what does that mean?


P1740 DODGE Torque Converter Clutch or Overdrive

You are having a Transmission Issue. There is a known issue with the TCC Lock-Up Solenoid. Once you Clean and Replace the Solenoid, your problem will go away (95% sure)

Apr 15, 2013 | 2000 Dodge Ram 1500 Truck

1 Answer

P1740 code on 2001 ram 1500 tcc-overdrive solenoid . how to test & replace


there is a total of 27 diagnostic steps to follow, but here is some info for you:
SYMPTOM
P1740-TCC O/D SOL PERFORMANCE

WHEN MONITORED
The Torque Convertor Clutch (TCC) and Overdrive Clutch (O/D) will be tested each time the PCM requests TCC engagement in 3rd gear and O/D.

SET CONDITION
The code will set if the expected RPM drop is not achieved while attempting to engage TCC or O/D. This indicates a malfunctioning torque convertor or overdrive clutch.

POSSIBLE CAUSES
- Camshaft DTC present
- Engine RPM DTC present
- Fuel level low
- Misfire DTC present
- Output speed DTC present
- P1765 DTC present
- Park/Neutral DTC present
- PTO engaged (if equipped)
- Torque converter clutch DTC present
- TPS DTC present
- Transfer case in low range (if equipped)
- Transmission Relay DTC present
- Transmission temperature too cold
- Intermittent
- Check transmission fluid-debris
- Check transmission fluid-stall
- 3-4 Shift Solenoid
- Oil Pan contains excessive debris
- Shaft or seal damage
- TCC solenoid
- Torque converter
var classElements = new Array(); var node = document; var tag = 'a'; var els = node.getElementsByTagName(tag); var elsLen = els.length; var pattern = new RegExp("(^'\\s)specs_note(\\s'$)"); for (i = 0, j = 0; i

Jun 03, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

My 2007 dodge with 5.9 diesel is showing engine malfunction light and error code of P1740, failed TCC or overdrive solenoid. The truck seems to run ok in overdrive but I don't understand what the TCC...


Code P1740-Torque converter clutch did not lock up when the PCM sent the command. Enabling conditions: No engine or transmissions codes are present, vehicle speed was under 70 MPH, TPS was under 33% open. When the PCM commanded the torque converter to lock, no change was detected in engine speed. Blocking action: This code can block the following monitors: none.

Testing: Check torque converter solenoid for proper operation.

NUMBER: 21-11-00
GROUP: Transmissions
EFFECTIVE DATE: October 02, 2000
SUBJECT: 46RE Transmission MIL Due To DTC P1740 - TCC or OD Solenoid Performance
OVERVIEW: This bulletin involves the replacement of the transmission pressure boost valve cover plate.
MODELS: 2000 - 2001 (AB) Ram Van 2000 - 2001 (AN) Dakota 2000 - 2001 (BR/BE) Ram Truck 2000 - 2001 (DN) Durango

NOTE: THIS BULLETIN APPLIES TO VEHICLES EQUIPPED WITH A 46RE TRANSMISSION BUILT BEFORE AUGUST 01, 2000 (MDH O8O1XX).

SYMPTOM/CONDITION:
The customer may complain of a Malfunction Indicator Lamp (MIL) illumination. Upon further analysis, it is determined that the MIL is caused by Diagnostic Trouble Code (DTC) P1740 - Torque Converter Clutch (TCC) or overdrive solenoid Performance. Other than the MIL, the customer may not notice any other condition with the transmission.

This condition may be caused by an intermittent and momentary TCC disengagement condition. The transmission valve body pressure boost valve cover plate has been revised with a larger size orifice hole to address this condition.

NOTE: THE DRB III(R) MUST BE OPERATING AT RELEASE LEVEL 50.4 MDS2 SYSTEM CIS CD2067 OR HIGHER (AVAILABLE THE WEEK OF OCTOBER 2, 2000) IN ORDER TO PERFORM THE REVISED TORQUE CONVERTER CLUTCH STALL TEST. DO NOT USE EARLIER VERSION STALL TEST TO DETERMINE CONDITION OF THE TORQUE CONVERTER CLUTCH.

Here can find the test in pdf format: 2009-11-28_034958_1124.pdf

Hope helps.

Apr 28, 2011 | Dodge Ram 3500 Cars & Trucks

1 Answer

I have a 2000 dodge durango with a trouble code p1740 what does it mean


SYMPTOM
P1740-TCC O/D SOL PERFORMANCE

WHEN MONITORED
The Torque Convertor Clutch (TCC) and Overdrive Clutch (O/D) will be tested each time the PCM requests TCC engagement in 3rd gear and O/D.

SET CONDITION
The code will set if the expected RPM drop is not achieved while attempting to engage TCC or O/D. This indicates a malfunctioning torque convertor or overdrive clutch.

POSSIBLE CAUSES


Camshaft DTC Present
Engine RPM DTC present
Fuel level low
Misfire DTC present
Output speed DTC present
P1765 DTC present
Park/neutral DTC present
PTO engaged (if equipped)
Torque converter clutch DTC present
TPS DTC present
Transfer case in low range (if equipped)
Transmission relay DTC present
Transmission temperature too cold
Intermittent
Check transmission fluid-debris
Check transmission fluid-stall
3-4 shift solenoid
Oil pan contains excessive debris
Shaft or seal damage
TCC solenoid
Torque converter

Aug 15, 2010 | Dodge Durango Cars & Trucks

1 Answer

P1740 code came on for a 2001 dodge ram 1500 what does it mean?


This is the OD Solenoid. There is a TSB out that covers the 2000-2001 Ram truck.

EFFECTIVE DATE: Oct. 02, 2000
SUBJECT:
46RE Transmission MIL Due To DTC P1740 – TCC or OD Solenoid Performance
OVERVIEW:
This bulletin involves the replacement of the transmission pressure boost valve cover
plate.
MODELS:
2000 - 2001 (AB) Ram Van
2000 - 2001 (AN) Dakota
2000 - 2001 (BR/BE) Ram Truck
2000 - 2001 (DN) Durango
NOTE: THIS BULLETIN APPLIES TO VEHICLES EQUIPPED WITH A 46RE
TRANSMISSION BUILT BEFORE AUGUST 01, 2000 (MDH 0801XX).
SYMPTOM/CONDITION:
The customer may complain of a Malfunction Indicator Lamp (MIL) illumination. Upon
further analysis, it is determined that the MIL is caused by Diagnostic Trouble Code (DTC)
P1740 - Torque Converter Clutch (TCC) or Overdrive Solenoid Performance. Other than
the MIL, the customer may not notice any other condition with the transmission.
This condition may be caused by an intermittent and momentary TCC disengagement
condition. The transmission valve body pressure boost valve cover plate has been revised
with a larger size orifice hole to address this condition.
DIAGNOSIS:
1. Warm the transmission to normal operating temperatures.
2. Using the DRB IIIò, perform a torque converter clutch (TCC) stall test. The stall test
has been revised so that the TCC remains engaged for a period of four (4) seconds.
NOTE: THE DRB III MUST BE OPERATING AT RELEASE LEVEL 50.4 MDS2
SYSTEM CIS CD2067 OR HIGHER (AVAILABLE THE WEEK OF OCTOBER 2,
2000) IN ORDER TO PERFORM THE REVISED TORQUE CONVERTER
CLUTCH STALL TEST. DO NOT USE EARLIER VERSION STALL TEST TO
DETERMINE CONDITION OF THE TORQUE CONVERTER CLUTCH.
3. If the engine stalls as a result of the TCC stall test, then perform the Repair
Procedure.
4. If the engine does not stall, as a result of the TCC stall test, then further diagnosis is
required. The technician may want to consider the following components during
their additional diagnosis: a cut or worn input shaft seals, a missing pump lock-up
circuit check ball, or worn converter hub, input shaft, reaction shaft, and pump rotor.
This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without written permission of DaimlerChrysler Corporation.
21-11-00 -2-
PARTS REQUIRED:
1 04617015 Plate, Pressure Boost Valve Cover (46RE)
1 02464324AB Gasket, Trans Pan
10(AR) 05010124AA ATF+3, Transmission Oil Type 7176 (2000 M.Y.)
10(AR) 05013457AA ATF+4, Transmission Oil Type 9602 (2001 M.Y.)
REPAIR PROCEDURE:
1. Clean the pressure boost valve cover plate to remove any dirt or rust inhibitor prior to
installation. The revised cover plate will have a 1.75 mm (0.069 inch) orifice hole
versus a 1.22mm (0.048 inch) orifice hole in the original plate. Make sure it is clean.
2. Using the appropriate Service Manual, Group 21 – Transmissions and Transfer Case,
replace the transmission pressure boost valve cover plate p/n 04617012.
3. Verify fluid level after warming up the transmission and cycling the shift lever several
times.
4. Verify, and if required, adjust the transmission shift linkage and the transmission
throttle valve cable per the appropriate Service Manual procedures.

Jun 10, 2010 | 2000 Dodge Ram 1500 Truck

1 Answer

Truck (2001 Dodge Ram 1500) runs fine. Check


I found that the code is set for:

P1740....TCC Solenoid or Overdrive Solenoid performance

which indicates that a rather inexpensive fix is in order, not a complete transmission replacement!! The TCC is the solenoid which controls the locking of the transmission converter so that you get better gas mileage with no "slippage" while at highway speeds, which is normal when the converter is unlocked as you slow down. If it is locked and the solenoid fails to release it the car will stall when you come to a stop since the fluid in the converter fails to act as a clutch and the engine is connected directly to the transmission input shaft. If it never locks then the oil in the transmission will overheat at highway speeds since ther "slippage" will always be present in the converter cauasing frictional heating of the oil.

Whenever you get a quote from a shop ALWAYS get at least two more!!! No matter what the job is, even a muffler replacement get many quotes. Go to a reliable transmission repair shop and ask for their opinion. In my humble opinion the shop that told you that you need a new transmission is just hungry for work - stay away!!!!

Bob

Apr 21, 2010 | 2001 Dodge Ram 1500 Truck 2WD

2 Answers

I have 2 engine codes for a 2001 dodge ram 1500 5.9 litre p0000,p1740


I have never seen P0000 but P1740 is a standard autotrans code it should have another code with it,P1740 just tells you that the fault is in the automatic transmission.

Nov 19, 2009 | Dodge Pickup Cars & Trucks

1 Answer

Trouble code P1740 on 1999 Dodge Ram 2500


I had the same code on my 2001 dodge 2500. The truck wouldn't shift from 3-4. I pulled the trans pan off and replaced a broken spring ($2.00). It is behind a thin plate with 3-4 small torq screws. You don't have to remove the valvebody. Only took me 45 minutes to fix.

I would like to give thanks to Jeff Russel from Teal automotive. He said this is a very common problem. He sells any part for any automatic Transmision and his prices are very affordable.
Here is a link to the website.
http://www.tealautomotiveinc.com/

Hope this helps.

Mar 15, 2009 | 2004 Dodge Ram

1 Answer

Error codes


Her is the definition and a list of possiable causes.


Code P1740-Torque converter clutch did not lock up when the PCM sent the command. Enabling conditions: No engine or transmissions codes are present, vehicle speed was under 70 MPH, TPS was under 33% open. When the PCM commanded the torque converter to lock, no change was detected in engine speed. Blocking action: This code can block the following monitors: none.
Testing: Check torque converter solenoid for proper operation.
P1740 TCC O/D SOL PERFORMANCE (GAS)
Theory of Operation
The Torque Converter Clutch (TCC) Solenoid is used to engage the TCC which improves fuel economy.
When Monitored
The Torque Convertor Clutch (TCC) and Overdrive Clutch (OD) will be tested each time the PCM requests TCC engagement in 3rd gear and OD.
Set Condition
The DTC will set if the expected RPM drop is not achieved while attempting to engage TCC or OD. This indicates a malfunctioning torque convertor or overdrive clutch.
Possible Causes
* ENGINE DTCS PRESENT
* TRANSMISSION DTCS PRESENT
* TRANSMISSION TEMPERATURE TOO COLD
* OIL PAN CONTAINS EXCESSIVE DEBRIS
* 3-4 SHIFT SOLENOID
* SHAFT OR SEAL DAMAGE
* TCC SOLENOID
* TORQUE CONVERTER

Sep 25, 2008 | 2005 Dodge Ram 3500

Not finding what you are looking for?
2000 Dodge Durango Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...