Question about 1995 Mitsubishi Diamante

1 Answer

Handbreak light on dash board remains on even while driving. Also at present fixing break pads had them bleed. Why is the light for the hand break on. Handbreak working just light remains on while driving

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,098 Answers

Hi

it is either the switch under the handbrake is jammed or the fluid level is low or has air in the system, park the car on a hill both up and down to see if the light goes off. get back to me if you need more info.

Regards

Dan

Posted on Jan 01, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a chevy silverado 04 with a manual trans and i hv never seen the handbreak lights ON, it stays off even when i use the handbreak. And is there any way to fix the rpm problem cuz once i shift the...


There may just be a burned out bulb in the dash or you may have a button not making a connection at the handbreak. The RPM issue it completely different and may have many causes.

Jan 04, 2015 | Cars & Trucks

3 Answers

Hand break light coming on with out using hand break


The cable tightness is loose therefore causing the light to come on while driving, tighten or replace the eb cable hope that helps or you need to push in the button on it hold the button and pull it back as far as you can. let go then push button pull back farther and release, this should tighten the tension.

Jan 02, 2015 | 1994 Chevrolet C1500

1 Answer

How do you adust handbreak on a volvo s40 2002


the hand break should adjust automatically when pulling on the hand break lever up and down with foot break down

Jul 28, 2014 | Volvo S40 Cars & Trucks

2 Answers

Handbreak light flashes on whilst driving


The hand brake leaver is not fully off , or the switch need adjusting.

Jun 27, 2014 | 2010 Nissan Qashqai

1 Answer

How much would it cost to fix handbreak light it on even when handbreak is on



The handbrake light is also the 'low fluid' warning light. It is connected to the handbrake as that ensures that it is checked every time you use the handbrake. If it remains on all the time, then check the brake fluid and top up if required. If the fluid is ok then it is probably the switch on the lever and is adjustable

May 08, 2014 | 2000 Ford Focus

1 Answer

Passat 03 handbreak light


This may be caused by low fluid in the master cylinder. Try topping up the master cylinder with fresh brake fluid that's recommended for your vehicle. 1_10_2014_2_26_42_am.png

Dec 17, 2013 | Cars & Trucks

1 Answer

My ABS light showin my my dash board and it was scanned my mitsubishi. Presently the light is still showing and when I break, I hear some noise as if the break pad is pad. I currently have new beak pad...


Hi,

New brake pads require 'wearing in' and may make a scraping sound for the first 50km or so.

Re ABS

First, I suggest you remove the PCM "Fuse" (in the main junction box, under bonnet) for 10secs, then re-insert. If you cannot find fuse, then disconnect NEG battery cable for 10secs. This will reset your PCM.

Start engine and allow to idle for 15mins (this allows the PCM to re-learn settings).

Drive car a short distance to determine if ABS light comes back on. If ABS light does come back on, then have the PCM scanned for fault codes. This will identify which ABS component is causing the (warning light) problem.

If light remains off (and the pads are worn in), but you still have scraping noise, then something else is causing this problem and will require further investigation.


Cheers,

Jun 15, 2011 | 2000 Mitsubishi Montero Sport

1 Answer

Car


This can be caused by nothing more than low brake fluid level. Check the level in the master cylinder. Add one the correct fluid as listed on the cap. If that is not the problem then you need to have your brake pads inspected.

Oct 29, 2009 | 2002 Renault Sportwagon

1 Answer

Handbreak light and stop light with a beep


Check the switch on your handbrake to see if it is loose or has been moved. They are usually somewhere close to the handle under your hand brake boot.

Jul 06, 2009 | 2004 Renault 181

2 Answers

Audi 80 1992


usually a sign of either airbag system failure, charging system failure, or brake system failure....i would have that checked out asap by a licenced mechanic

Sep 18, 2008 | 1992 Audi 80

Not finding what you are looking for?
1995 Mitsubishi Diamante Logo

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...