Question about 2001 Chevrolet Malibu

1 Answer

Have a 2000 malibu and cant get the key to fully return to "off" position....engine will turn off but radio and position lights stay on...battery was replaced yesterday but completely dead this afternoon..need a solution

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hello My firiend, I had the same problem like you two times, basically what the technician told me was that the mechanism of the transmission shaft was worn, so what you only need to do is to "push" the shaft from the chrome rod and thatt's it.

Sorry if you I could not explain you exactly how to solve this, My english in not so good at this time so I hope that this works for you.


My email address is: javier_nava_ceballos@hotmail.com

Posted on Jan 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My key is stuck in the ignition.


Your car has several different ignition positions. They each offer slightly different functionality.
Off: In this position, the engine is off, and so are your electronic accessories (unless the delay has not expired yet). You can still turn on lights (headlights, interior lights, etc.).
ACC: This is the accessory position. Turn the key to ACC if you want to listen to the radio, play a CD or use other accessories without cranking the engine.
On: In this position, all of the electronics should come on. This is also the position that the key will return to after cranking the engine.
Start: Turn the key to this position to crank the engine. Let go of the key when the engine is running and the key will return to the on position.

http://www.aa1car.com/library/ignition_switch_positions.jpg

I use to own a car that had an ignition that was ACC - OFF - ON - START.

Try turning your ignition one position clockwise and see if the radio turns off and the key comes out.

https://hackadaycom.files.wordpress.com/2008/08/ignition.jpg?w=450&h=338

Jan 29, 2017 | Cars & Trucks

Tip

Chevrolet service light 1991-01


Camaro

1998-01

To reset the "OIL CHANGE" light, press and hold the "TRIP/OIL RESET" button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset.


Corvette


1997-01

To reset the monitor after an oil change, turn the ignition on. Press the "TRIP" button so that the "OIL LIFE" percentage is displayed. Press "RESET" and hold it for two seconds. The word "RESET" should appear on the monitor, then "OIL LIFE 90%".


Impala,
Monte Carlo


2000-01

Turn the ignition to ON without starting the engine. Fully press and release the accelerator three times within five seconds. If the CHG OIL SOON lights two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not been reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to exit programming. A chime will be heard to verify the exit.


Impala,
Caprice


1994

To reset the "CHANGE OIL" light, turn the ignition switch to the run position with the engine off. Access the reset button on the end of the instrument panel by the fuse block. Press the switch and hold it for at least 5 seconds.



Lumina,
Monte Carlo,
Impala,
Caprice


1996-00,
1996-99,
1995-96,
1995-96

To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds. The light will flash and go out.


Corvette


1990-96

After an oil change, or when "CHANGE OIL" appears on the Trip Monitor, with the ignition on and engine off, press the "ENG MET" button (located on trip monitor) once. Press the "ENG MET" button again within 5 seconds. Within 5 seconds, press and hold the "RANGE" button (1990-1994) or "GAUGES" button (1995). The light will flash. When it stops flashing and goes out, the system is reset.


Chevrolet Suburban,
GMC Yukon XL,
Chevrolet Silverado,
GMC Trucks Sierra


2000-01,
1999-00

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.


Silverado, Sierra Trucks


1991-93

To reset the "CHANGE ENGINE OIL" message, turn the ignition key to the run position. Press and release the accelerator pedal three times within 5 seconds. If the light flashes for 5 seconds, the system is reset. Repeat procedure as needed.















on Dec 07, 2009 | Chevrolet Camaro Cars & Trucks

1 Answer

2001 Chev Malibu. Turn key on to start car, won't start. No warning lights on no lights on gauge panel. Radio works, dome light work.


check the ground leg to your engine.. it runs off the neg. battery terminal. will connect to frame and engine.. pull it off, wire brush it put it back.. you radio will work, 'cause it draws much less current, and is grounded in dash.

Jan 11, 2013 | 2001 Chevrolet Malibu

1 Answer

I cant turn my key to the off position on my 2000 chevy malibu ! what is the problem ?


is the car fully in park if it is then u may have a prob with the park lock. In normal operation the key wont turn off all the way if it is not in park check to see if the censor is working or engaging. If all is working correctly then it might be that the tumblers in the ignition lock cylinder are the problem

Nov 11, 2011 | 2000 Chevrolet Malibu

1 Answer

Coolant Light My coolant light went on in my "98 Chevrolet Malibu, so I put some coolant liquide and than the light still on? What can I do?


reset your ecm by tuening key to on position and turnning you a/c on and remove positive battery cable. wait 30 sec. then turn off key and replace battery cable. good luck to ya.

Mar 26, 2011 | 2003 Chevrolet Malibu

1 Answer

Car won't start. Battery power seems fine. Turn the key, no cranking, lights and radio die with key in "start" position.


Hello davidoz,

Your description sounds like a bad battery. Do you have a volt meter to watch the voltage as you turn the key to start? The voltage on a good battery( meaning fully charged) should stay about 11 volts while cranking, if it drops below that suspect a bad battery.

Another possibility is that the battery is good but the alternator is not charging.

Will it start with a jump? If is does check with a volt meter the out put of the alternator it should be 13.8 volts or slightly higher.

Regards,
netvan

Mar 09, 2011 | 2000 Pontiac Grand Am GT

1 Answer

Car wont start. when key is turned i get weird clicks.


You said you checked your battery, did you check volts and amps? It's possible that your battery is not functioning properly. You may need a new one. Does it start if you try to jumpstart it?

Nov 12, 2009 | 2004 Chevrolet Malibu

1 Answer

1999 malibu, engine turns, won't start, guages not


You checked all fuses? Dis-connect positive battery lead for a few seconds and reconnect. Do you have spark & fuel?

Aug 09, 2009 | 1999 Chevrolet Malibu

3 Answers

Dont know how to reset or bypass gm theft system car is not starting .It tries and quits.


this is one way to reset it :
first make sure the battery is fully charged , then do the following:
key in the ignition but do not crank the motor, just leave it at the
ignition mode for ten minutes ,then turn it off POSITION for 5 seconds then REPEAT again 2 more times. at the 3 rd time youre gonna notice the ANTI THEFT light on dash to blink. when doing the last step , remove key , inserted again and turn on motor , good luck , AJ

May 28, 2009 | 2001 Chevrolet Malibu

1 Answer

My radio and shift selector light stays on when I remove the key,


The ignition cylinder has a taper at the back that move the switch in whatever position. The key has to be turned back to off. It happened to me when I pulled the key out it was still half way on but then i just move it back in place. Its a sloppy cylinder from age.

Mar 13, 2009 | 2000 Chevrolet Malibu

Not finding what you are looking for?
2001 Chevrolet Malibu Logo

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...