Question about 1998 GMC Jimmy

1 Answer

Im replacing my front brakes and i cant get to the bolt that holds the braket

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 360 Answers

Generally, turning the wheels either hard right or hard left will produce needed clearance when trying to remove mounting bolts. Are you using a socket and ratchet, or a end wrench? Sometimes it's necessary to use a end wrench.

Be sure to not OVER TORQUE the bolts when doing the re-assembly. If you have any doubts about torque values, purchase a vehicle specific repair manual from your local auto parts store (Pep Boy's, Advance, Auto Zone, O'Reilly's, etc.) and you'll find the needed info.

Also be sure to adequately clean the pad holders, caliper slides, pins, etc. and lube as required before re-assembly.

Good luck!

Posted on Jan 01, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove slk230 accelerator pedal


Hi,not as strait forwould as you would think,you need to first undo the cover under the steering,then you have to disconnect the brake master cylinder from the brake peddle and the cables to the switches then undo the bolts that hold the braket that holds the peddles,then when you have done that you can take the clip off the end of the braket to release the peddle,I hope this has been some help,my advice would be to buy a haynes maneul to refers to,all the best.

Nov 11, 2015 | 2002 Mercedes-Benz SLK-Class

2 Answers

What size caliper bolt in a 2009 Hyundai Elantra?


12 mm ,14,mm wrench or socket that to remove the caliper 17 mm wrench or socket for the bolt holding the brake pad braket

Mar 14, 2015 | Hyundai Cars & Trucks

1 Answer

Cant get bolts out of cv axel support braket in a mazda 626


This is a bracket mount that has the axle shaft going thru it on the passenger side . the axle must be removed from mount before it can be removed . there is a single bolt that presses against the axle shaft bearing and a snap ring that holds the bearing in the mount once removed the axle will slide out .

Mar 21, 2014 | 1997 Mazda 626

3 Answers

I need to remove my front axel on my 1989 toyota camry


Jack up car and apply e-brake. car will roll if one of the front tires leaves the ground. remove tire , spindal nut and lower ball joint bolts. remove axle from hub then use a prybar to pop it out of trans. the passenger side will have a braket holding axle to engine , remove bolts from braket or squeeze snap-ring to rmove axle from braket.

Jan 11, 2011 | 1989 Toyota Camry

1 Answer

Drivers side wheel bearing what do i need to do to replace it myself


Front - Remove tire, then remove brake caliper and caliper braket, remove brake rotor, some times will have little clips, remove clips, if they break ok, won't used them again, if 4X4 remove center axle nut, disconnect ABS harness, on back side of bearing, there will be three bolt's that hold hub bearing assembly, remove bolts, bearing should slide out, some time with a little help from a hammer, and your done , reverse to install new hub bearing assembly, just make sure that ABS harness is in same location that old one was when putting bearing in.

Jul 21, 2010 | 2004 Mercury Mountaineer

1 Answer

Changeing front bearing hubs


remove the tire, then remove the brake caliper and its braket then slide rotor off. next is to remove the center axle nut, now look on the backside, you will see the bolts that hold bearing asm, in place remove bolts and hub comes off, you may have to beat hub with a hammer to break free, note if you have abs system disconnect connector before removing hub. reverse directions to install.

Jan 19, 2010 | 2003 Chevrolet Impala

1 Answer

How do I replace a 2005 Pontiac Grand Prix front wheel bearing. Do I need a press?


no its a bolt on, must remove wheel brake caliper and its braket then brake rotor, look at back of spindle you will see 3 bolts ,remove them and hit frt of hub until it comes out . good luck.

Oct 20, 2009 | 2005 Pontiac Grand Prix

2 Answers

How to remove the rear rotors on a gmc 2002 2500 hd extra cab 4x4


The rotors are one with the hub.s, So, you need to pull the axles , hub bearings. Good Luck

Sep 18, 2009 | 2002 GMC Sierra 2500HD

1 Answer

Issues replacing front rotors


The brakets can be removed by removing two (2) fairly large hex head bolts on the back side of the wheel assembly. Apply a small amount of WD-40, but do not get any on the other brake parts. Using an extension pipe on the handle of a 3/8 inch rachet you should get enough leverage to break the bolts free. Make CERTAIN you are using a snug fitting socket to avoid rounding the hex head bolts, or you job will get twice as difficult. If all else fails you can spot apply some heat to the bolt head, and then try loosening the bolt again. Avoid heating up any grease areas or rubber parts. I generally use a pipe extension that is about 12 inches in length, as opposed to just the short rachet handle.

May 25, 2009 | 1993 Suzuki Sidekick

1 Answer

Grand am gt 2003


Jack that side up support it with jack stands or blocks, take off tire, take brake calipar off, brake calipar braket, take off rotor, take off axel hub nut, and the 3 bolts that hold the hub assembly on, then bang it off with a good hammer. Installation is just reverse.

Apr 08, 2009 | 2003 Pontiac Grand Am

Not finding what you are looking for?
1998 GMC Jimmy Logo

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...