Question about Ford F-150

1 Answer

I have a 2002 f-150 pickup. I recently changed the brake pads in front. Now my cruise control will not work. I believe it has to do with the cruise deactivation switch in the brake line. I would appreciate help in reseting the switch. Thanks tom

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 376 Answers

The abs wheel speed sensors are tied into the cruise control circuit, they are used to tell the computer the vehicle speed, have it scanned for abs codes.

Posted on Jan 01, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the number for the fuse for cruise control in a 04 mountaineer


I have to say that the cruise have a fuse in works in since with the brake pedal. There will be two of them 1 will control the brake lights and the other the cruise control. I believe that the blue 1 is the cruise. Change that 1 and all should be fine. Hope this helps.

Dec 21, 2014 | 2004 Mercury Mountaineer

1 Answer

S10 cruise control


Brake switch, make sure the brake lights are working.

Dec 18, 2013 | Cars & Trucks

2 Answers

My brake pads have been replaced, however the dash brake warning light still appears. In addition, the cruise control is not working. This has reset a few times and the light has gonen out adn the cruise...


Look at your brake master cylinder, open the top to it, and check your brake fluid. If low, that is why the brake light is on. Or check to see if your emergency brake is pushed in. Check your fuses for the cruise control. Hope this helps, James Booth

May 17, 2011 | 2004 Mercury Mountaineer

1 Answer

Cruise control not working.. 2002 expedition 5.4 lt


There is a pressure switch in the front of the Master Cylinder, I believe if you change it that may fix your problem. This is a starting point, not the only solution, There is a switch located by the brake light switch that could not be working, This switch can also be one in the same as the stoplight switch. Fuses is anothere option. Because of where I work I tend to overtroubleshoot. But the switch in front of the master Cylinder is a common problem.
In our computer it is a cruise control pressure switch.

Jan 09, 2011 | 2002 Ford Expedition

1 Answer

Lost brake lights and cruise


have you 12 volts at the brakelight bulb holder?as with a lot of pickups the wires on the body get broke i would say a broken wire live/netural/ground good luck.adrian,,,,,,

Jul 30, 2010 | 1989 Toyota Pickup SR5

1 Answer

I recently replaced my brake booster. After the


hello there:
you may have over looked the vacuum line for the cruise control that hooks up to or close to brake booster hope this helps you out..sincerely D.Jones

Jun 06, 2010 | 1997 Ford Taurus

1 Answer

While driving home from work my ABS light illumintaed then my 4X4 high light began flashing. What do you think the problem might be?


For some year models of Explorers involved in the Cruise Control recall, there were additional wiring problems caused by the modification of the Cruise Control. These problems included yours and Brake lights working independent of the brakes. Contact a dealer about this SECOND service bulletin.

The above problems are more likely if the 4x4 is showing a light and the vehicle is in 2 wheel drive. The ABS indicator light is usually to be trusted without the Cruise problem. It would not hurt to check the brake pad linings, sometimes the lining shifts and drops down off the metal of the pads. Finally if the ABS light is still showing a problem that you can not find, check the Emergency brake pads inside the rear rotors.

Feb 06, 2010 | 2004 Ford Explorer

1 Answer

How do i change the rotors on my 1995 4x4 pickup?


Here is a link to a complete video guide on how to repalce brake pads and rotors which should help you immensely...

http://www.wonderhowto.com/how-to/video/how-to-replace-front-brake-pads-and-rotors-on-an-automobile-225061/

Nov 01, 2009 | 1992 Toyota Pickup

1 Answer

Yellow DSC and Brake light on... recently changed brake pads


Abs and dsc are related and with the light on these won't work. It is possible that you need to go back to where the work was done to look this over.

Jun 07, 2009 | 2003 BMW 325

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...