Question about 1996 Toyota Camry

1 Answer

Installing radiator - 1996 Toyota Camry

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 242 Answers

REMOVAL
1. DRAIN ENGINE COOLANT
2. w/ CRUISE CONTROL SYSTEM:
REMOVE CRUISE CONTROL ACTUATOR COVER
3. DISCONNECT ECT SWITCH CONNECTOR FROM FAN SHROUD
4. DISCONNECT ELECTRIC COOLING FAN CONNECTORS
5. REMOVE RADIATOR HOSES
(a) Disconnect the upper hose from the radiator side.
(b) Disconnect the lower hose from the water inlet pipe.
6. DISCONNECT RADIATOR RESERVOIR HOSE
7. A/T:
DISCONNECT OIL COOLER HOSES
8. REMOVE RADIATOR AND ELECTRIC COOLING FANS
(a) Remove the 2 bolts and 2 upper supports.
(b) Lift out the radiator.
(c) Remove the 2 lower radiator supports.
9. REMOVE RADIATOR LOWER HOSE
10. A/T:
REMOVE A/T OIL COOLER HOSES
11. REMOVE ECT SWITCH WIRE
12. REMOVE ELECTRIC COOLING FANS Assembly is reverse order.

Posted on Jan 01, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the radiator on a 2007 chrysler sebring limited 3.5


REMOVAL

  1. Disconnect negative cable from battery.
  2. Remove radiator upper crossmember support. WARNING: DO NOT REMOVE THE CYLINDER BLOCK PLUG OR THE RADIATOR DRAINCOCK WITH THE SYSTEM HOT AND UNDER PRESSURE BECAUSE SERIOUS BURNS FROM COOLANT CAN OCCUR.
  3. Drain the cooling system.
  4. Remove the radiator fans.
  5. Disconnect coolant reserve/recovery hose.
  6. Remove vapor purge solenoid from mounting bracket.
  7. Disconnect upper and lower hoses from the radiator.
  8. Remove the A/C condenser side brackets to radiator attaching screws. Separate the condenser from the radiator by lifting upward to disengage from lower mounts. Allow the condenser to rest in front of radiator.
  9. Radiator can now be lifted free from engine compartment. Care should be taken not to damage radiator cooling fins or water tubes during removal.
  10. INSTALLATION

    1. Be sure the air seal is in position before radiator is installed. Slide radiator down into position. Seat the radiator with the rubber isolators into the mounting holes provided, with a 10 lbs. force.
    2. Position air conditioning condenser onto the radiator lower mounts and install upper screws. Tighten fasteners to 5 Nm (45 in. lbs.).
    3. Install the radiator upper and lower hoses.
    4. Connect the coolant reserve/recovery hose.
    5. Connect the vapor purge solenoid to the mounting bracket.
    6. Install the radiator fans.
    7. Install the radiator upper crossmember support.
    8. Fill the cooling system.
    9. Connect negative cable to battery.

Nov 10, 2016 | 2007 Chrysler Sebring

1 Answer

How do i replace the radiator on a 2003 Buick Lesabre


3.8L Engine

  1. Drain the engine coolant.
  2. Remove the upper radiator seal.
  3. Remove the upper tie bar.
  4. Disconnect the coolant overflow hose from the radiator.
  5. Plug the coolant overflow hose.
  6. Disconnect the upper and lower radiator hoses.
  7. Remove the transaxle oil cooler pipe bracket bolt from the lower tie bar.
  8. Remove the cooling fans.
  9. Slide the plastic cap off the transaxle oil cooler pipe quick connect fittings.
  10. Disconnect the upper and lower transaxle oil cooler pipes from the radiator.
  11. Remove the A/C condenser mounting bolts.
  12. Separate the condenser from the radiator.
  13. Lift the radiator up and out of the vehicle.
To install:
  1. Install the radiator to the vehicle. Place the bottom of the radiator in the lower pads.
  2. Install the condenser to the radiator.
  3. Install the A/C condenser mounting bolts and tighten to 115 inch lbs. (13 Nm).
  4. Push the upper and lower transaxle oil cooler pipes into the radiator quick connect fittings, until a "click" is heard.
  5. Tug gently on the cooler pipes to ensure proper retention.
  6. Slide the plastic caps (1) over the quick connect joints.
  7. Install the cooling fans.
  8. Install the transaxle oil cooler pipe bracket bolt to the lower tie bar and tighten to 89 inch lbs. (10 Nm).
  9. Install the upper and lower radiator hoses.
  10. Connect the coolant recovery hose to the radiator neck.
  11. Install the upper tie bar.
  12. Install the upper radiator seal.
  13. Fill the cooling system.
  14. Inspect the transmission oil level.

Nov 02, 2015 | Buick Cars & Trucks

1 Answer

Change out cooling system radiator


RADIATOR
REMOVAL 1) Disconnect negative cable from battery. 2) Discharge the A/C system. 3) Remove the front fascia.
WARNING: DO NOT REMOVE THE CYLINDER BLOCK PLUG OR THE RADIATOR DRAINCOCK WITH THE SYSTEM HOT AND UNDER PRESSURE BECAUSE SERIOUS BURNS FROM COOLANT CAN OCCUR. 4) Drain the cooling system. 5) Disconnect the radiator fan electrical connectors. 6) Disconnect coolant reserve/recovery hose. 7) Remove A/C lines. 8) Remove the auxiliary transmission cooler hoses. 9) Remove the pushpins and the upper radiator seal.


10) Remove the pushpins and the LH and RH radiator seal (Fig. 20).

11) Remove the A/C condenser side brackets to radiator attaching screws (Fig. 22). Separate the condenser from the radiator by lifting upward to disengage from lower mounts (Fig. 22). Allow the condenser to rest in front of radiator. 12) Remove the upper and lower radiator hoses.

13) Radiator can now be lifted free from engine compartment. Care should be taken not to damage radiator cooling fins or water tubes during removal. (Fig. 21) 14) Remove the auxiliary transmission from the radiator module. 15) Remove the cooling fan assembly from the radiator module. INSTALLATION
1) Install A/C condenser, (if removed). 2) Install radiator fan assemble, if removed. 3) Install auxiliary transmission cooler, if removed. 4) Slide radiator down into position. Seat the radiator with the rubber isolators into the mounting holes provided, with a 10 lbs. force. 5) Install mounting screws. 6) Connect the cooling fan electrical connector. 7) Install the radiator upper and lower hoses 8) In the LH and RH radiator seals. 9) Install the upper radiator seal. 10) Install the auxiliary transmission cooler hoses. 11) Connect the coolant reserve/recovery hose. 12) Install the front fascia. 13) Fill the cooling system. 14) Connect negative cable to battery

Apr 02, 2014 | 2004 Chrysler Pacifica

1 Answer

How do I remove my car radiator?


Section 303-03: Cooling, Engine 1997 Explorer, Mountaineer Workshop Manual REMOVAL AND INSTALLATION Radiator - 4.0L Removal
  1. NOTE: Refer to following illustrations.
    Drain the cooling system by removing the radiator cap (8100) and attaching a 9.5 mm (3/8 inch) inside diameter hose to the draincock nipple, located at the lower rear corner of the radiator tank. Then, open the radiator draincock (8115) and allow the coolant to flow through the hose into a suitable container.
  1. Loosen hose clamps at throttle body and engine air cleaner assembly. Remove air cleaner outlet tube and position aside.
  1. Remove radiator overflow hose from the radiator, disconnect two hose locators at top of radiator and position hose aside.
  1. Remove two fans shroud bolts. Lift the fan shroud out of the lower retaining clips and position it on the fan blade.
  1. Position upper and lower radiator hose clamps, remove hose from radiator and position it on the fan blade.
  1. Disconnect the two transmission cooling lines from the oil cooler fittings on the radiator, install protective caps over lines and position aside.
  1. Remove two upper radiator bolts.
  1. Tilt the radiator back (rearward) approximately 25 mm (one inch) and lift directly upward, clear of the radiator support bracket and the fan blade.
Installation
  1. Position the radiator into engine compartments, make sure that mountings on both tanks are inserted into radiator support brackets. Install radiator retaining bolts. Tighten to 6-8 - (54-70 lb-in).
  1. Remove protective caps from cooler lines. Connect the two transmission cooling lines at the oil cooler fittings on radiator. Tighten to 16-24 - (12-17 lb-ft).
  1. Install upper radiator hose and position hose clamp. Tighten to 3 - (26 lb-in).
  1. Install lower radiator hose and position hose clamp. Tighten to 3 - (26 lb-in).
  1. Position fan shroud in lower retaining clips and install upper bolts. Torque to 6-8 - (54-70 lb-in).
  1. Position radiator overflow hose, connect to radiator and locators.
  1. Position air cleaner outlet tube to throttle body and air cleaner assembly. Tighten to 2-3 - (18-27 lb-in).
  1. Fill the cooling system; refer to Cooling System Draining, Filling and Bleeding in this section.

Oct 28, 2010 | 1997 Mercury Mountaineer

1 Answer

How do i remove radiator fan from my 2004 pt cruiser?


Hope this helps!

Removal & Installation
NOTE The fan motor, fan, and the shroud are serviced as an assembly.



CAUTION Do not open the radiator draincock with the system hot and under pressure, because serious burns from coolant can occur.


  1. Disconnect negative cable from battery.
  2. Remove battery and battery tray.
  3. Drain cooling system below upper radiator hose level.
  4. Remove grille.
  5. Remove upper radiator closure panel and center brace.
  6. Disconnect upper radiator hose from radiator.
  7. For turbocharger equipped vehicles: Remove radiator inlet neck.
  8. Hoist vehicle.
  9. Disconnect radiator fan electrical connector (.
  10. Remove the two lower and left side radiator fan screws and.
  11. Lower vehicle and remove the remaining radiator fan attaching screws.

    WARNING Care should be taken not to damage the radiator cooling fins and tubes during fan removal.

  12. Remove radiator fan by lifting up from the engine compartment.

c83d6ac.gif
Radiator fan mounting points

To install:
  1. Install the radiator fan into position on the radiator.
  2. Hand-start all radiator fan fasteners.
  3. Tighten all radiator fan retaining screws to 55 inch lbs. (6 Nm).
  4. Connect the radiator fan electrical connector.
  5. Carefully lower the vehicle.
  6. For turbocharger equipped vehicles: Inspect radiator inlet neck O-ring. Replace if necessary. Install radiator inlet neck. Torque fasteners to 55 inch lbs. (6 Nm).
  7. Connect the upper radiator hose to radiator. Align hose and position clamp so it will not interfere with the engine or the hood.
  8. Install upper radiator closure panel and center brace.
  9. Install grille.
  10. Install battery tray and battery.
  11. Connect cables to battery.
  12. Fill cooling system.

Apr 18, 2010 | 2004 Chrysler PT Cruiser

1 Answer

What is the procedure for removal of the radiator from the Mercury Mystique(1998 model)?


Ford Contour/Mystique/Cougar 1995-1999 Repair Guide

Radiator -REMOVAL & INSTALLATION
(see Figures 1 through 7)

7249321.jpg
Fig. 1: Remove the upper radiator hose from the radiator


d2d2436.jpg
Fig. 2: Use a back-up wrench to remove the transaxle cooler line connections-automatic transaxle only


3213ac8.jpg
Fig. 3: the lower transaxle cooler line connection


ec9272d.jpg
Fig. 4: Remove the passenger side radiator mount and ...


956cd3d.jpg
Fig. 5: ... and the driver's side radiator mount


f06fec0.jpg
Fig. 6: The condenser can be support using mechanic's wire as shown here, or another suitable device


242d821.jpg
Fig. 7: Carefully lower the radiator out the bottom of the vehicle
  1. Disconnect the negative battery cable.
  2. Drain and recycle the engine coolant.
  3. Remove the upper radiator hose from the radiator.
  4. On 2.5L equipped vehicles, remove the radiator overflow hose from the radiator.
  5. On vehicles equipped with an automatic transaxle only, remove the transmission cooler line from the cooler inlet fitting and plug the line and the fitting.
  6. Remove the engine fan.
  7. Raise and support the vehicle.
  8. Remove the lower radiator hose from the radiator.
  9. On vehicles equipped with an automatic transaxle only, remove the transmission cooler line from the cooler outlet fitting and plug the line and the fitting.
Remove the cooler lines while holding the radiator connector with a back-up wrench.
  1. Support the radiator, and A/C condenser with a jackstand or other suitable device.
  2. Remove the lower radiator supports from the front of the subframe.
  3. Remove the two retaining bolts for the A/C condenser from the brackets at the bottom of the radiator.
  4. Position the jackstand aside and remove the radiator out the bottom of the vehicle.
To install:
  1. Carefully raise the radiator into place and support the radiator with a jackstand or other suitable device. Install the two retaining bolts for the A/C condenser into the brackets at the bottom of the radiator.
  2. Install the lower radiator supports and tighten the bolts to 71-97 inch lbs. (8-11 Nm).
  3. Remove the jackstand and install the transmission cooler outlet line (if equipped) and the lower radiator hose to the radiator.
  4. Lower the vehicle.
  5. Install and tighten the fan shroud nuts.
  6. Install the transmission cooler inlet line (if equipped) and the upper radiator hose to the radiator.
  7. On 2.5L equipped vehicles, install the radiator overflow hose from the radiator.
  8. Connect the negative battery cable.
  9. Fill the cooling system with the proper 50 / 50 mixture and start the vehicle.
  10. Bleed the cooling system and check for leaks.

Hope helps with this (remember rated this help) Good luck.

Jan 20, 2010 | 1996 Mercury Mystique

2 Answers

How to remove a radiator from a ford taurus


Disconnect battery ground cable. Remove battery. Remove battery tray. Remove clip retaining contant control relay module and position module aside. Remove radiator cap. Raise vehicle front end as high as possible. Remove radiator splash shield. Drain radiator. Remove the radiator mounting bracket assembly. Remove lower radiator hose. Partially lower vehicle. Remove upper radiator hose. Remove radiator overflow hose. Remove upper A/C condenser core retaining bolts. Remove upper transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Raise vehicle. Remove lower transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Remove transmission oil cooler bracket and position transmission oil cooler aside. Remove lower A/C condenser core bolts and position A/C condenser core aside(be careful not to loosen the AC condenser lines. Remove radiator support bracket. Remove radiator out through the bottom of the vehicle.
Installation
Position radiator. Position radiator support bracket and tighten nuts. Position A/C condenser core and tighten lower A/C condenser core bolts. Position transmission oil cooler tube and install transmission oil cooler tube bracket. Install lower transmission oil cooler tube. Install lower transmission oil cooler tube clips. Install lower radiator hose. Install radiator mounting bracket assembly. Tighten bolts. Install radiator splash shield. Lower vehicle. Install upper tranmission oil cooler tube. Install upper transmission oil cooler tube clips. Install upper A/C condenser core retaining bolts. Tighten bolts. Install radiator overflow hose and tighten clamps securely. Install upper radiator hose. Position constant control relay module and clip securely. Install battery tray. Install battery. Connect battery ground cable. Fill and bleed cooling system. Start engine and inspect for leaks.

Nov 25, 2009 | 1998 Ford Taurus

2 Answers

Radiator replacement


  1. Remove air cleaner and duct assembly.
  2. Drain the coolant.
    1. Remove the engine mount struts.
    2. Remove the cooling fans with the cooling fan shroud.
    3. Remove the radiator upper hose from the radiator.
    4. Remove the radiator lower hose from the radiator.
    5. Disconnect the transaxle oil cooler lines from the radiator.
    6. Remove the radiator brackets and bolts.
    7. Remove the radiator. Installation Procedure
    1. Install the radiator. Notice: Refer to Fastener Notice in Service Precautions.
      1. Install the radiator brackets and bolts.
        • Tighten the bolts to 24 Nm (18 ft. lbs.) .
      1. Connect the transaxle oil cooler lines to the radiator.
      2. Install the radiator upper hose to the radiator.
      3. Install the radiator lower hose to the radiator.
      4. Install the cooling fans with the cooling fan shroud.
      5. Install the engine mount struts. Notice: When adding coolant, it is important that you use GM Goodwrench DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) coolant. If Coolant other than DEX-COOL (R) or HAVOLINE (R) DEX-COOL (R) is added to the system the engine coolant will require change sooner; at 50,000 km (30,000 mi) or 24 months.
      6. Fill the cooling system.
      7. Install the air cleaner and duct assembly.

Jun 28, 2009 | 2000 Chevrolet Venture

1 Answer

Radiator replace


I Hope you Find this Helpfull And Please Remember to RATE ME

  1. Drain the coolant.
  2. Disable the SIR.
  3. Move the forwarding discriminating sensor out of the way.
  4. Remove the air cleaner assembly.
  5. Remove the cooling fans.
  6. Disconnect the radiator inlet hose from the radiator.
    1. Disconnect the radiator outlet hose from the radiator.
    2. Disconnect the engine oil cooler lines from the right radiator end tank.
    3. Disconnect the transmission oil cooler lines from the left radiator end tank.
    4. Remove the left and the right engine torque struts.
      1. Remove the upper radiator support screws.
      2. Remove the radiator from the vehicle. Lift the radiator up and out. INSTALLATION PROCEDURE
        1. Install the radiator to the vehicle.
        2. Install the upper radiator support screws. Tighten the bolts to 6 Nm (53 inch lbs.). NOTICE: Refer to Fastener Notice in Service Precautions.
        3. Install the transmission oil cooler lines to the radiator. Tighten the transmission oil cooler line fittings to 27 Nm (20 ft. lbs.).
        4. Connect the engine oil cooler lines to the radiator. Tighten the engine oil cooler lines to 18 Nm (13 ft. lbs.).
        5. Install the left and the right engine support torque struts.Connect the radiator outlet hose to the radiator.
          1. Connect the radiator inlet hose to the radiator.
          2. Install the cooling fans.
          3. Install the air cleaner assembly.
          4. Install the forward discriminating sensor.
          5. Enable the SIR.
          6. Refill the coolant.
        6. Hope this Helps and PLEASE RATE ME

Jun 03, 2009 | 1998 Cadillac DeVille

Not finding what you are looking for?
1996 Toyota Camry Logo

367 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...