Question about 2008 Audi A4 Sedan

1 Answer

My car would take a long time to build up speed and today it wont start

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 750 Answers



Posted on Jan 01, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

1999 kia sephia hesitate to pick up speed then surges all of a sudden why thank-you

if it starts and runs wont be
timing marks or crank angle sensor
or coils

any engine check light on ?
could be the air idle sensor
fuel pump pressure to the rail


Apr 11, 2017 | Kia Cars & Trucks

1 Answer

My dodge grand caravan today threw a 700 engine code transmission module, car wont go over 25 and only has powered acceleration for first 5 seconds car is on.

700 is a generic transmission code. It went to limp mode, that's why it drives like it does. Have the codes read with a newer /better code reader or a scanner. Find out what other codes are in there.

Aug 02, 2015 | 2001 Dodge Grand Caravan

2 Answers

1990 vw cabriolet. Thanks guys for the suggestions to my problem but tried it all but still wont start. Both pumps are working, new pressure regulator. It started yesterday but I cranked the engine for a...

Sounds like you have one or both of the belts off by a tooth. Did u use cam locks to hold the camshafts in place. If it is a zero tolerance engine you may have messed a few things up.

Mar 04, 2015 | 1990 Volkswagen Cabriolet

1 Answer

I have a 2006 Audi A4 with a multitronic (CVT) transmission. Over the past several days, under heavy acceleration, the engine will stop building rpms. This has happened at different speeds several times. I...

These cars are very complex and it's not easy to diagnose. You should take it to a qualified technician with the proper electronic disagonstic tools to verify the problem. Start off with a full scan. It may be a simple as a software upgrade or as complex as the tranny needing repair. I wouldn't drive the car hard and get this resolved asap.

Sep 17, 2010 | 2006 Audi A4

1 Answer

I've been working on a 2004 Kia Rio and it still dosent wanna act right. The motor has been rebuilt a few years ago along with the transmission, and ever since the trans build I keep having Codes come up...

you have a or some loose wires my friend. check carefully all the grounds one may be loose from the previous repair work look on trans grab the big ground cable from battery and see if it s loose at the bolt check area of intake manifold for loose grounds
then check for shorted wires look at the ones that go to all the sensors.most of the sensors share the 5 volt supplie wire and share the ground wire. the only ones that are seperate are the signal return wires
yours has codes for a bunch of sensors so i would concentrate on the 5 volt supplie and the ground
5 years ago a guy brought his rio into our dealership for a clutch and the tech stripped the bolt that comes from batt. ground to the transmission case. it came back 4 days later with all the codes like yours i found the loose ground at the stripped bolt and put a longer bolt in. car never came back

Mar 22, 2010 | 2004 Kia Rio

1 Answer

When I push the gas pedal my car's check engine light starts flashing and my vehicle boggs down and wont build up speed. When i let off the gas a little my car then slowly starts to pick up speed and my...

That may very well be correct.Asking for acceleration needs a strong spark and these parts will provide that.
All that for $242 installed? Great deal.

Oct 24, 2017 | 2000 Hyundai Accent

1 Answer

What causes my mitsubishi 3000gt wont start and my fuel injertors overflow theres a fire on the on the sparplug but it just wont start and i just changed my ignitioin ciol and still wont start i check the...

check timing it should be 5 b tdc 600 idle speed . this is for manual or automatic . check fuel pressure it should be 38 psi. when check timing idle speed should be at 600-800 rpms.your timing has to be checked using a scanner only. not adjustable with timing light.

Mar 29, 2009 | 1999 Mitsubishi 3000GT

Not finding what you are looking for?
2008 Audi A4 Sedan Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

80339 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides