Question about Dodge Durango

Open Question

How to change a tensioner pulley on a 2001 dodge durango

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 82 Answers

SOURCE: 2001 dodge durango v8 4.7

It is acually called the vehicle speed sensor I do believe. It should should be located on the top of your transmission with a wiring harness attached to it. It should also have 1 bolt holding it in also. Whatever you do, do not rotate the gear when you remove it. Try to mark the exact way it came out when you replace the sensor. When you pull the sensor out it will have this gear attached to it which will need to be placed into the new sensor and put back into the vehicle in the same way it came out or you will throw a code and it will not be pretty. Good luck, hopefully I didn't scare you it can be a simple repair just mind your P's and Q's.

Posted on Jan 07, 2009

polarcycle
  • 1392 Answers

SOURCE: Change front brake pads on 2001 dodge durango

Front, remove the hold down clip, should be a 7mm or a 45 torx bit to get the slider pins out. If you are not sure what you are doing, please spend a little money and have a pro do it for your safety, and the safety of others around you.

Posted on Mar 18, 2009

  • 412 Answers

SOURCE: removal of tensioner pulley in a 2003 Dodge Neon

the tensioner is part of the engine mount bracket..not serviced seperately as far as i know

Posted on May 23, 2009

  • 4088 Answers

SOURCE: 1999 dodge durango 5.9 v8 loud squealing noise

You didn't mention the alternator, power steering pump, or water pump. In fact, any pulley other than the crankshaft one can have a bad bearing or dry seal. Remove the belt and spin each pulley while listening for any rough noise or squeal. If it was the crankshaft, it might be time to check the oil. Start the engine with the belt off to see if it does squeal. Make sure the noise isn't coming from the radiator fan(s).

Posted on Nov 17, 2009

  • 1 Answer

SOURCE: my 2001 dodge durango is overheating an leaking coolant from a round plug type thing in the corner on the passenger side near the windshield

What exactly is the "round plug type thing" near the firewall [passenger side]? Is it a sensor of some type? I, too, have a coolant leak here on my 2001 Durango; its tucked in rather tightly near the hood/firewall corner. My electric fan is not kicking on; vehicle overheated tonight. (4.7 liter)

Posted on Dec 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change the belt


need to take tension off spring loaded pulley with tool sometimes a bolt sometimes a square hole, find tool at parts store , follow diagram near hood latch for belt routing, release tension remove old , install new release tension , good to go

Mar 15, 2011 | 2000 Dodge Durango

1 Answer

Car is overheating. I think the wrong tensioner pulley is installed. we bought the right one according to the parts store. if the tensioner pulley is not providing the right tension on the belt can it...


First off if your belt is slipping enough for the water pump to not function it should be making one heck of a racket.
look at the belt (carefully and with protective wear) and see if the water pump pulley is spinning when the engine is running.
more likely your culprit may be a thermostat or if when the belt came off the last time the vehicle overheated, it may have cause internal damage, head gasket etc.

Jan 01, 2011 | 2001 Dodge Durango

1 Answer

I am trying to change the serpentine belt on my 4 cylinder Dodge Dakota Sport (2001). Which pulley is the tensioner?


the tensioner will be bulky & look like it spring loaded . some will have a place you can put a racket in a square to pull up on tensioner

Nov 19, 2010 | 2001 Dodge Dakota

1 Answer

What size is the engine on a 2002 dodge durango R/T? Need to change the surpentine belt.


4.7L or 5.9L and it should be listed on a sticker somewhere in the engine compartment.

---
Drive Belt Removal & Installation 3.7L, & 4.7L Engines To Remove:
dak_97-04_47l_drv_blt.gif

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Disconnect negative battery cable.
  3. Rotate tensioner until it stops.
  4. Remove belt and slowly rotate the tensioner back to its free position.
To Install:
  1. Install new belt and route around all pulleys except idler pulley.
  2. Rotate the tensioner arm until it stops.
  3. Route the belt around the idler pulley and slowly let the tensioner rotate back to its free position.
3.9L, 5.2L, & 5.9L Engines To Remove:
NOTE: Check the belt routing label, located in the engine compartment, for the most current belt routing schematic.
CAUTION
Do not attempt to check tension with a belt tension gauge on vehicles equipped with an automatic belt tensioner.
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Attach a socket wrench to the pulley mounting bolt of the automatic belt tensioner and rotate the tensioner assembly clockwise until tension is relieved.
  3. Remove or disconnect the following:
    • Belt from idler pulley
    • Belt from vehicle
To Install:
  1. Position drive belt over all pulleys except idler pulley.
  2. Attach a socket wrench to automatic belt tensioner and rotate the tensioner assembly clockwise.
  3. Install belt over idler pulley, allow tensioner to rotate back into place, and remove the wrench.
prev.gif next.gif

Sep 03, 2010 | 2002 Dodge Durango

1 Answer

How do you losseb the serpentine belt tensioner on a 2000 durango, 5.9L?


There is a tensioner pulley that is spring loaded and you need a large wrench or breaker bar to take the tension off (or can rent a tensioner pulley wrench at your local auto parts store)

May 01, 2010 | 2000 Dodge Durango

1 Answer

I own a 1999 dodge durango slt 5.9, I keep hearing squeaks from under the hood. i had replace the pollys, belts and the tension. but still squeaking needs help fast!


Do you mean pulleys? Squeaks or Squeals ? Try some belt dressing, or to locate the culprit remove one belt at a time to see what belts and or pulleys are making the noise...

Sep 30, 2009 | 1999 Dodge Durango

1 Answer

How to change a serpentine belt 2004 5.7 hemi? I just need to know where to look for a belt tensioner, etc. do i have to remove shrouds and covers?


run the engine and watch the belt pulleys, the one that jitters and moves up and down is the tensioner pulley, it is an arm with a pulley on the end, it is a very short arm.

Sep 03, 2009 | 2004 Dodge Durango

1 Answer

The front belt, toward radiator, does not have a tensioner. How do I change it. 2001 Dodge Intrepid, 2.7 ltr.


IT DOES HAVE A TENSIONER PULLEY..SMALLER PULLEY LOCATED TO THE LEFT OF P/S PUMP..LOOSEN NUT ON FRONT OF PULLEY(15MM WRENCH)..AND THERE IS A BOLT LOCATED JUST BEHIND PULLEY(13MM SOCKET)LOOSEN THIS AND REMOVE BELT..IT IS EASIER TO REPLACE BELTS WITH UPPER RAD SUPPORT REMOVED..I HOPE THIS HELPS

Aug 26, 2009 | 2001 Dodge Intrepid

2 Answers

2001 dodge durango


Check your Belt Tensioner. If it is not keeping the Belt Tight Enough you will have the Above Problem.

Jan 25, 2009 | 2000 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...