Question about Ford E-250

1 Answer

When I put to reverse it won't move - E-250 Ford Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 45 Answers

Could be a bad relay in the trans, or the bands have gone bad

Posted on Jan 01, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 isuzu axiom won't move when put in drive or reverse


ur linkage come un clipped from the rod that goes into the transmission or ur bands need adjusted if its a clutch bleed the clutch

Feb 27, 2013 | 2003 Isuzu Axiom

1 Answer

!996 Toyota corolla, starts up ok but when put on reverse or drive, won't move even when pushed


Check the gear lever connection with the gearbox.
Check the gearbox oil level and colour. Replace if necessary.

Nov 13, 2012 | 1996 Toyota Corolla

1 Answer

Won't move when put in gear


Its your transmission yu will need to get a new one or used one

Sep 27, 2012 | 2002 Chevrolet Impala

1 Answer

2004 nissan altima 2.5s will start but won't move in any gears


You have a failed automatic transmission. You will need to remove and replace it or have it rebuilt.

May 31, 2012 | Cars & Trucks

1 Answer

Car won't move when started?


Fill up to proper level. If it still doesn't move check drive train.

May 26, 2012 | 1999 Lexus RX 300

1 Answer

My 1998 Honda civic ex won't move but the motor


Have you just replaced the clutch? Taken out the transaxle, and put it back in? Are you sure transmission was in good condition before this? If so, review your procedure carefully to be sure you got it all back right.
Watch the slave cylinder while someone depresses clutch. You should see the little plunger move slightly out and move the clutch lever back. The lever moves the release bearing inside bell housing into contact with the pressure plate. If slave cylinder doesn't move at all, try bleeding again. The plunger has to move when clutch is engaged.
I'm not sure what you mean by "will shift but won't go into gear". You mean it's actually going into a gear position and car won't move? Or it won't go into any gear, period. As if you had no clutch?

Nov 06, 2011 | 1998 Honda Civic

1 Answer

My car won't go in gear neither one it won't move


check linkage, and fluid level,also check emergancy brake (hey iv'e done it )

Sep 20, 2011 | 1997 Chevrolet Lumina

1 Answer

When you put it in drive or second it won't move when you push the gas but if you put it in 3rd or reverse it will move


theres a problem with the planetary gearing-----valve body------or bands and clutches-----------bring it to an honest shop or visit magicmechanic.net

Sep 04, 2011 | 1999 Oldsmobile Silhouette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...