Question about 1984 Dodge D150

1 Answer

Pulled plugs and they were blackend - 1984 Dodge D150

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 189 Answers

Black plugs woul mean it's flooding,(too much gas)

Posted on Oct 15, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cant start a ford telstar 1991 got spark and petrol but cant get it to run?


Sounds like a lean fuel condition, did you check the fuel regulator, thats pretty common on older vehicles, it might be dumping too much fuel judging by your blackend plugs. Also should stop using fuels with ETHANOL, the **** ruins fuel systems, just ask anyone.............

Sep 02, 2012 | Ford Cars & Trucks

1 Answer

Hi, I have a 2003 toyota 4runner v8 with about 120k mi. on it, and have a steering problem. The steering wheel is hard to turn as if there is no power assist, alternating between hard and normal. I had...


If you check the fluid leves and this is OK, them likely means something came loose in the pump. The only way to be sure with out replacing the pump is take it to a shop where they can hook up a pressure and read pump out put pressure.

Check if you havebits of metal in the fluid sounds like something in either the control valve or steering gear has broken down, this could go to bad sttering pump.

Keep us updated.

Mar 14, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

The power seat in my 1998 Dodge Durango will move forward and tilt, but it will not go backwards. Any idea what could be wrong and how do I fix it?


It sounds like a loose wire or dirty connection. Look under the seat to see where the wire clip is and unplug it if its dirty or blackend brush it with a brass brush then blow it out hook it up. If that doesnt fix it check the switch for the same or just replace it! Best of luck...

Oct 21, 2010 | 1998 Dodge Durango

1 Answer

Dashboard light won't go on and them smoke came from under dashboard?


Look at this as a guess and please leave me a thumbs up if I get lucky but NOT a thumbs down if I don't have the right answer OK? I can't afford a bad mark for trying to help someone.
The smoke you saw may have been only the fuse burnning out. This is not a serious thing unless it continues to blow more fuses. We now need to get you under the dash and locate the fuse box. Some boxes are covered by a flap that blends in with the dash so if you don't see the box by looking under the left hand driver side then look for that flap and pull down or off or what ever. Once you find the box you should see a diagram on the front of the cover or behind the cover. You will be looking for one marked instrument panel. But in your case with the smoke you need to check every single fuse. that one fuse may have taken more then one with it. Pull each one 1 at a time and look to see if the wire inside it is melted in the center or blackend. If the wire is good it will look clean and the wire will be one complete wire with an arch to it. That is unless yours are the old glass type but same therory. the wire inside must be complete.
Make sure the key is out of the ignition before replacing the bad one/ones. Replace with only the same amp fuse that came out of it. Mark and remeber where the bad fuse was. After you have checked all the fuses then with your flashlight look at the surrounding wiring for any melted wires under that area of the dash and under where you saw the smoke come from. If you find melted wire under there then remove the bad fuse you replaced until you can get good wire spliced into the melted wire.
If you do not see any melted wire then come up and turn the ignition switch to on and watch and listen for another pop. See if the dash lights come back on if you don't see smoke or hear the pop. If they do then you should be good to go. Fingers crossed at my end. Remember me in your kind works, Raz

Apr 20, 2010 | 1996 Volvo 850

2 Answers

The relays on a 93 ford tempo aren't working.. how do i fix it?


check the fuse links at the starter solenoid and the main red wire under the fuse panel

Jan 20, 2010 | Ford Tempo Cars & Trucks

1 Answer

No high/low beams but have running lights


if it goes out like that (while driving) it's probably a wiring issue - check at all connection points that you can (at plug/fuse box/etc.) for visible damage to the wires such as very sharp bends or if the outer coating looks shiny (even when dry) compared to other wired around it or looks bubbly or an area that looks burned/blackend/significantly darker than the rest of the wire (of what you can see)

Sep 18, 2009 | 2001 Chevrolet Cavalier

1 Answer

1992 Ford Bronco tail, and dash lights not working, why?


Sounds like the fuse...check all of your fuse under and around the drivers side dash...it could also be the light bulbs are burnt out...pull the bulbs out and check to see if they are blackend

Apr 18, 2009 | 2004 Nissan Sentra

2 Answers

'98 Buick Century has no odometer/gear selector display


The resisters on the back of the odometer fell off. they can be re solder if you can find them. That is what happened to mine. i stumbled on video directions on youtube. just pull out you cluster. there are 4 resisters on ther right top side of the of the PC board. if there still there they will be blackend and burned. just roll your finger on them and if they fall off easy there bad. you can buy replacement resistors for like $3 and same your self a $100 to fix or worse. buying a new one. ther resistors i used were 1/2 watt 150Ohm 5% tolerance resistors. and they can be bought from any raido shack. i hope this helps.

Mar 13, 2009 | 2001 Buick Century

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...