Question about 2002 Cadillac Deville

2 Answers

What all has to be taken off to get to to the oil pan gasket

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 6,826 Answers

Oil Pan REMOVAL & INSTALLATION

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence what all has to be taken off to get to to the oil - 7922vg08.gif
prev.gif next.gif

Posted on Jan 01, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cadillac Master
  • 14,036 Answers

REMOVE OIL LEVEL INDICATOR HARNESS CONNECTOR,REMOVE EXHAUST CROSSOVER PIPE.REMOVE THE TRANSAXLE ASSEMBLY FROM THE ENGINE

Posted on Jan 01, 2011

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: how much to change a oil pan gasket for 2001 grand prix 3.8 gt

If you want to repair the oil pan I would also check lower engine mount for leaking oil and cracks in anti sway bar near fitting's. This due to engine mount is oil filled. OEM sway bar is made of tubular steel and they crack easy. Replacement sway bar is solid steel. Here's the kicker. When they pull the lower frame to service oil pan. The engine mount and sway bar are attached to that frame. A honest mechanic should only charge for parts ($35 for mount and $100 for sway bar) and maybe a extra hour. My mechanic did all in 5 hours. FYI gasket is only $35 bucks. Good luck

Posted on Mar 02, 2010

  • 1596 Answers

SOURCE: Oil Pan Gasket Replacement - How to - GMC Yukon 2000








Removal Procedure

Important: The original oil pan gasket is retained and aligned to the oil pan by rivets. When installing a new gasket, it is not necessary to install new rivets.
DO NOT reuse the oil pan gasket. When installing the oil pan, install a NEW oil pan gasket.

Caution: Refer to Battery Disconnect Caution in Service Precautions.

  • Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnect/Connect Procedure
  • Remove the front differential if equipped with four wheel drive. Refer to Differential Carrier Assembly Replacement in Front Axle.
  • Remove the under body shield from the vehicle
  • Remove the oil pan underbody shield.
  • Remove the cross brace if equipped.
  • Drain the engine oil and remove the engine oil filter. Refer to Engine Oil and Oil Filter Change
  • Remove the lower transmission-to-oil pan bolts
  • Disconnect the oil level sensor electrical connector.
  • Remove two front wiring harness retainer bolts.


10. Remove the engine wiring harness retainer bolts from the engine oil pan.
11. Remove the engine oil cooler pipe to oil pan bolt.
12. Remove the transmission oil cooler pipe retainer and the bolt from the oil pan.
13. Remove the starter motor. Refer to Starter Motor Replacement.
14. Remove the left closeout cover and bolt.
15. Remove the engine oil pan. Refer to Oil Pan Removal.

Installation Procedure

Important: The alignment of the structural oil pan is critical. The rear bolt hole locations of the oil pan provide mounting points for the transmission bellhousing. To ensure the rigidity of the powertrain and correct transmission alignment, it is important that the rear of the block and the rear of the oil pan must NEVER protrude beyond the engine block and transmission bellhousing plane.

Will Send Remainder in another this place dont take kindly to larg files Your Email Address would realy be Better Then I could send Pictures Also up to YOU

Posted on Jan 27, 2009

  • 3 Answers

SOURCE: To change the oil pan gasket in a 93 Tercel

is not hard, i changed mine 95 tercel

Posted on Oct 24, 2008

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

  • 1 Answer

SOURCE: Trying to drop the oil

done this on several i-6 f-150s. slide back or remove transmission, remove motor mount bolts from frame(not motor), jack motor up as far as possible without damaging egr valve or wiper motor when they hit, shim under motor mounts so that when you drop the jack the motor does not come back down any(the motor is well balanced on the mounts, it will not fall out of the truck like a v8 will), then remove the oil pan. you May have to remove the pickup tube(usually not), and you May have to rotate the crankshaft so that the lobes clear the oil pan. this is a common problem with these trucks due to the size of the oil pan(Huge), and the minimum pan to crossmember clearance

Posted on Apr 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove oil pan on a 2001 gmc Sonoma pick up truck to replace gasket


1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN ...

? 2:31
https://www.youtube.com/watch?v=1KsRTlnW7Cg
Sep 27, 2011 - Uploaded by JohnSmiths8379858
trying to reomove the oil pan to this truck has been sitting for about 6 ... 1993 GMC SONOMA 2.6 CYL V6 NOT 4x4 OIL PAN REMOVAL "HELP!

Oil Pan Gasket: How to Change Oil Pan Gasket for 2001 ...

www.2carpros.com/questions/2001-gmc-sonoma-oil-pan-gasket
Mar 18, 2011 - How to change oil pan gasket for 2001 sonoma, can i get away with just raising the engine two inches to ... 2001 GMC Sonoma • 4 cylinder 2WD Automatic • 150,000 miles ... You need to remove the engine to get the sump off.

Nov 28, 2015 | GMC Cars & Trucks

1 Answer

Using a fel pro gasket kit, whats the oil pan bolt tightening sequence on a 69 chevy 250ci l6?



this is taken right from the manual.
thisth

Insert a screw on each side and at each end of the

pan to position the gasket.

2. Carefully position the oil pan in place, make

sure the gasket is not misaligned and tighten the

screws inserted in Step 1 finger-tight.

3. Install the remaining screw and tighten all to

specifications. Work from the center
outward in each direction.

Oil pan

Side screws 7 ft-lb

End screws 1 0 ft-lb
Drain plug 23 ft-lb

Nov 10, 2014 | Cars & Trucks

2 Answers

How do I remove an oil pan from a 2002 malibu, 3.1 liter


When you say the pan will not drop down do you mean that it is still stuck to the block. If that is the case manufacturers use a gasket material ( sealer that is an adhesive to glue the pan to the block and so reduce oil leaks at the gasket. You may have to use something like a paint scaper and a hammer to cut the gasket free..

Oct 28, 2014 | 2002 Chevrolet Malibu

3 Answers

I'm having probalems getting the oil pan off, i've taken every possible bolt that i can see off, still cannot get it loose... or to drop


If it won't come off the engine it (should just be a gasket) maybe siliconed on, and you will have to pry it off. If it is loose but won't come down its because of the oil sump pick-up that drops down deep into the oil pan. You may have to loosen the fornt mount and lift the motor up, or reach in and unbolt the sump from the oil pump. Some late models with aluminum oil pans had bolts going thru the tranny bell housing to the oil pan for alignment of the pan, but I doubt yours does.

Jan 30, 2011 | 2000 Chevrolet Monte Carlo

1 Answer

How to replace oil pan gasket on 2002 deville


Oil Pan REMOVAL & INSTALLATION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the crankcase.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Oil level indicator harness connector, if equipped
    • Exhaust Y-pipe, if needed
    • Transaxle assembly from the vehicle.
    • Oil pan bolts and the oil pan
    To install: NOTE: The oil pan gasket is reusable unless it is damaged. Do not remove the gasket from the oil pan groove unless gasket replacement is required.
  4. Thoroughly clean the inside of the oil pan and the cylinder block contact surface. If the oil pan gasket is being reused, be careful not to damage it. Do not expose the gasket to cleaning solvents.
  5. If a new gasket is being installed, start the gasket into the oil pan groove and work the gasket into the groove in both directions. Once the gasket is exposed to oil, it will expand and no longer stay in the groove without wrinkles. If this condition exists, replace the gasket.
  6. Install or connect the following:
    • Oil pan. Torque the bolts, in sequence, to 89 inch lbs. (10 Nm).
    • Oil level indicator connector, if removed
    • Transaxle assembly, if removed
    • Y-pipe, if removed
    • Flywheel cover, if removed
    • Oil pan drain plug. Torque it to 15 ft. lbs. (20 Nm).
    • Negative battery cable
  7. Refill the crankcase.
  8. Run the engine and check for leaks. Fig. 1: Oil pan bolt torque sequence 7922vg08.gif
prev.gif next.gif

Oct 29, 2010 | 2002 Cadillac Deville

1 Answer

Replace oil pan gasket 2002 chrysler 300m


The owner of the car should be able to locate and replace oil pan gasket .prepare the equipment to be used .Drain the oil from the oil pan ,spill it to an empty big can that can carry the oil from the oil pan.Then twist the bolts that connect the oil pan to the engine.After removing the bolts then you have take the old gasket off to the oil pan.After taking off the old gasket then you have to replace it with the new oil pan gasket.then return the oil pan with the new gasket. twist the bolt back until the oil pan that connect the oil pan with the engine.And return the drain plug twist until it will not spill.

Sep 30, 2009 | 2001 Chrysler 300M

1 Answer

Oil leak repaired the oil pan gasket still leaking what can it be?


good morning and welcome to fixya.

lets see if we cant get you some help here, you say you installed a new oil pan gasket and tightened all the bolts to spec. did you clean the mating surfaces completely and use a gasket sealer i.e high tack, gasket may have slipped when reinstalling could be on the end of pan, have you pin-pointed the spot where it is leaking from? you might run a dye test on it. could be leak coming from above running down disguising itself. not sure what steps you have already taken. if you could let me know so i can help you more. thank you again, and you and i will get you leak fixed

Mar 09, 2009 | 1999 Dodge Intrepid

2 Answers

Oil Leak


i would have to say the oil pan gasket. that is the one that I have replaced more often. it is ever usual for the rear main seal to go out but not impossible. but i would have to say oil pan gasket.
hope this helps and if you need anything else let me know. happy holidays.

Tom

Dec 19, 2008 | 1995 Oldsmobile Aurora

Not finding what you are looking for?
2002 Cadillac Deville Logo

763 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...