Question about 2006 Toyota RAV4

1 Answer

How do i remove the rear bumper from a 2006 rav4 xt4 please.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 22,246 Answers

Never done one as yet ,but just look for the bolts it cannot be that difficult

Posted on Jan 01, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove & install new front & rear bumpers 2006 Kia Sportage?


The easiest way for you to do that is to find on the new bumpers where the fixing points are (try to look for little holes, like where do screws go, or clips, even on the inner parts) and then try to locate them on the existing bumpers and remove them. After that, remove the old bumpers and instal the new ones by the exactly same steps.

Apr 25, 2014 | 2006 Kia Sportage

1 Answer

How to remove 2006 toyota sienna rear bumper


I have written a detailed step-by-step tutorial on how to remove and replace the bumper of a 2004-2007 Toyota Sienna on my blog: John Fixes Stuff How to Remove the Front Bumper on 2004 2007 Toyota Sienna

Mar 19, 2013 | 2006 Toyota Sienna

1 Answer

How to remove rear bumper 2006 lr3


open hatch you have retainers on either side around wheel wells you have screws on bottom you have retainers remove all retainers and screws than pull on sides and bumper cover comes off.

Jul 29, 2012 | 2006 Land Rover LR3

2 Answers

How do I remove the back bumper from a 2006 hyundai tuscon?


take help of the following steps to remove rear bumper on ur tucson.

Open the trunk of your vehicle.
  1. Unscrew all the screws on the inside plastic trim that covers your bumper to trunk connection.
  2. Pry the plastic piece out with a flathead screwdriver. You will expose the bolts that attach the rear bumper to the trunk.
  3. Unscrew the bolts connecting to the inside of your rear bumper. There should be four bolts.
  4. Unscrew the two to four screws connecting to your bumper from the inside of the rear wheel tire wells. These screws are on the area of the tire well that is closet to the bumper.
  5. Slide under the rear of your car. Use a flathead screwdriver to pop the plastic rivets out of place along the underside of the rear bumper. There should be four to six rivets.

  6. Squat behind your car and firmly pull the bumper off. There will popping plastic sounds, this is the pop-in-place plastic rivets that are the last pieces that hold your rear bumper in place.

Dec 27, 2010 | 2005 Hyundai Tucson

2 Answers

I have a 2006 Ford Explorer and 2 of my park aid assist sensor are bad. They are in the rear bumper. How would i replace the sensors? Is it really necessary to remove the bumper?


You only need to remove the bumper cover. Remove both tail lamp assemblies. Under the tail lamps you will a 10mm and a 8mm bolt, remove these. Look into each rear wheel well rearward and you will find a T20 torx screw on both sides, remove these. On the top of the rear bumper, between the bumper and the bottom of the liftgate opening you will find 6 to 8 plastic rivets that can be removed by pulling the center pins out, remove these. At this point you should be able to lift upward and rearward and release the bumper cover. Once the cover is free you must disconnect the electrical connector to the sensor wiring harness. With the bumper cover on the ground or a bench, you will see 4 9/16" nuts that hold the styrofoam bumper cushion to the bumper cover, remove these. Now you should be at the point where the backup sensors are accessable. When you install the new sensors be sure your electrical connectors click when they connect. these connectors go on hard and if they don't click you will be doing this job again. Reassemble in reverse order.
Hope this helps

Apr 01, 2010 | 2006 Ford Explorer

1 Answer

How to replace the rear bumper cover on a Chrysler Pacifica


1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

Feb 16, 2010 | 2006 Chrysler Pacifica

1 Answer

Replace parking light on 2006 beetle


Rear parking lamp assembly (2006 New Beetle) is held in the bumper with a spring clip. I removed the assembly using a flat screwdriver to very gently pry out of the bumper. The clip is on the outboard side of the assembly, so you must pry from the outboard side using great caution to not mar or scratch the paint. The inboard side "hooks" to the bumper and slides outward once the clip clears the bumper on the other end. The bulb and socket can be removed by pulling outward from the assembly.

Jan 28, 2010 | 2006 Volkswagen New Beetle

1 Answer

I lost my toyota RAV4 model XT4 2004 manuals book


you can try ordering one on the ebay

Oct 13, 2009 | 2004 Toyota RAV4

1 Answer

2004 toyota rav4 rear bumper assembly guide


there are two bolts to the center and two around the corner on at the edge up high and one at the bottom of the bumper/ Please rate my response thank you very much

Jun 16, 2008 | 2004 Toyota RAV4

Not finding what you are looking for?
2006 Toyota RAV4 Logo

Related Topics:

522 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...