Question about 2006 Chevrolet Silverado

1 Answer

Is it neccesary to remove front diff to change axle brgs & seal

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 217 Answers

No you do not have to remove it

Posted on Jan 01, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1992 f150 front axle to diff. seal replacement


OK, you must remove the front axle assembly to access the axle flange and then the seal, follow the instructions at the link but once the axle is out remove the axle flange from the front diff and replace the axle seal, use a seal driver and lube the new seal with lithium grease (white grease). You will need an air impact to get the flange nut off, replace it with a new one (do not reuse) and do not over tighten it. Cinch it down and then go about 1/8 more of full nut rotation to preload carrier bearing setting then spike in place. Ford F150 Front Axle Replacement Part 1

May 19, 2016 | Ford F-150 Cars & Trucks

1 Answer

Should transmission fluid leak out when I remove front axle seals on my 2000 blazer xr2


No Transmission Fluid in the front diff (gear oil)

Steering Knuckle Seals-there is no fluid,
just the front drive axles

Have to explain where your working & on what
vehicle component

You shouldn't have trans fluid leak from anything

Aug 26, 2014 | Cars & Trucks

1 Answer

How do you replace the rear axle seal on a 1992 buick roadmaster


remove the wheel and brake drum then remove rear diff. cover put transmission in neutral roll rear diff. around until you see an 8 mm bolt , remove bolt then diff. pin then push axle in to un key axle key then pull axle out to get to seal remove seal with seal remover tool

Oct 05, 2013 | Buick Cars & Trucks

1 Answer

Rear axle seals leaking


If the axle had a slight grouve in it,you would see or feel it

If you distort the seal on install,you would be aware of that

I would try a different brand seal & install not quite as far
in the housing, until it seats,then you will be using a different
surface on the axle

If the seal leaks on the outside of the metal shell, you need
permatex #2 or similar product, if the seal isn't rubber coated

Jun 09, 2012 | 1995 GMC Sierra

1 Answer

I have a 98 ford f150 4wd rear diff is howling bad under load and coast no noise at no load had bad rear axles and brgs even though i didnt think this would fix it i replaced them as i expected, no...


the bad bearings and axles probably caused damage or wear to the gears / pinion when under load the bearings keep the axles straight and keeps downward pressure from loads off the gears and gear bearings --look at gear mesh will probably be off very slightly and not from backlash shims but from ring gear bearings or pinion bearing damaged

Apr 26, 2017 | Ford F-150 Cars & Trucks

3 Answers

How to change my front differential seal and bearing ? passenger side. I bought a new wheel bearing because of a humming sound on passenger side and doing so saw leaking seal and maybe the humming was...


That will be a Huge job. The whole front diff must come out of the car and the case will need to be taken apart to even gain acess to the carrier side bearings.
The hub bearing is where the wheel bolts up is that maybe what you are talking about?
Also the axle seal isn't that bad to do you need to remove the cv shaft then it's just a simple remove the seal and install the new one.
But all of these jobs will be big ones.

Oct 13, 2009 | 1999 GMC Jimmy

2 Answers

Front pass side cv axle removal on 2003 hyundai santa fe


pull swiftly !!! on the axle hub
as its got a big circlip in there & that is why it feels STUCK!
Cheers Rob

Aug 15, 2009 | 2004 Hyundai Santa Fe

1 Answer

Change front differential seals in 1996 gm sierra


In order to replace the seals, remove the front diff assembly. To remove the passenger side seal, I would suggest removing the tube assembly (5 bolts). This is due to a steel washer that goes on the end of the axle. If you just pop the axle out, it is tough to get the washer aligned and back on the shaft. Use anerobic sealer to seal the housing to the diff case. The drivers side you can pop out with a hammer.

Jul 02, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

2005 Yukon Front Diff Axle seals


You don't have to remove the whole diff to change the seals, but you will have to seperate it where the shaft meets the carrier housing. There is a clip holding the passenger axle shaft in place that you have to remove to change the seal. The drivers side axle stub can be removed with a little force as there is a spring clip holding that side in.

Sep 01, 2008 | 2003 GMC Yukon

Not finding what you are looking for?
2006 Chevrolet Silverado Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...