Question about 2002 Mazda Protege

1 Answer

How do i pull the hub off my 2002 mazda , on drivers side front

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 6,826 Answers

REMOVAL & INSTALLATION Except Miata FRONT

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Steering knuckle from the vehicle
    • Inner oil seal from the knuckle
  3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
  4. Remove or disconnect the following:
    • Bearing inner race from the front wheel hub
    • Retaining ring from within the knuckle
    • Front wheel bearing from the knuckle, using the hub puller tools
    • Brake dust shield
  5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
  6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
  7. Using the press tools, press a new wheel bearing into the knuckle assembly.
  8. Install or connect the following:
    • Wheel bearing retaining ring
    • New oil seal using Installation tool 49 V001 795
    • Front wheel hub using the Mazda press tools
REAR
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
  2. Remove or disconnect the following:
    • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar) how do i pull the - 7923mg87.gif

    • Brake drum, if equipped
    • Rear caliper and rotor assembly from the hub, if equipped
    • Hub dust cover
  3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
  4. Remove or disconnect the following:
    • Hub retaining nut and discard it
    • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle 7923mg86.gif
    To install:
  5. Install or connect the following:
    • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
    • Stake the nut into the groove in the spindle
    • Dust cover
    • Assemble the brakes
    • Rear wheel

Posted on Jan 01, 2011

  • Duane Wong
    Duane Wong Jan 01, 2011

    You may want to consult autozone.com for further diagrams and information.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Window wont go up


Power window repair - Mazdas247




www.mazdas247.com > ... > Mazda Protege Forum > Protege How-To

Aug 8, 2005 - 10 posts - ‎10 authors

I have a 2002 and last week the driver's side power window died a horrible death. ... Check out my mods -> 2001 Mazda Protege LX aka Rum Runner ... My front pass sidewindow won't go up or down anymore. haven't taken ...


Passenger Window on 2007 CX-7 will not come up ...

2 posts

Nov 28, 2012


Driver's side window auto-up/down issues - Mazdas247

15 posts

Jun 10, 2011


Power Window Problem - Mazdas247

7 posts

Aug 9, 2009


Driver Side window controller won't work

14 posts

Nov 11, 2006


More results from www.mazdas247.com




2003 Mazda Protege 5 Replacing The Power Window Motor ...





? 7:02


https://www.youtube.com/watch?v=N3GP2UwTtAQ

Feb 3, 2015 - Uploaded by Steve K.

2003 Mazda Protege 5 Replacing The Power Window Motor and Regulator. Steve K. ... Looks like you just ...





Amazon.com: Dorman 741-741 Mazda Protege Fr


Oct 30, 2015 | 2002 Mazda Protege

1 Answer

1998 Mazda 626 LX-When driving, a rubbing noise is coming from the front driver side wheel. Was told it was the front wheel hub assembly. Would like to replace bothsides( bearings etc). How do I order...


Hope your mechanic is right cos that is a costly job. Try calling around your local parts dealers, aka Autozone, Advance, Oreilly for prices on parts.

Feb 03, 2010 | 1998 Mazda 626

2 Answers

How to change front wheel bearings on a KE 89 model please ":)


im havent had to much experience with mazdas but for most cars you can buy the hub and replace the whole thing at once remove tire then remove brake pads and rotor un bolt the 2 bolts that bolt to strut then drop lower balljoint then pull cv joint out of hub there should be 3 bolts holding hub on the engine side remove bolts pull off hub replace

Jul 25, 2009 | 1988 Mazda 323 Hatchback

1 Answer

94 mazda protege removal front driveaxles both sides


If we're talking about the CV shafts, they have to first be popped out of the Hub, then they are pulled from the transmission.

Jul 21, 2009 | 1994 Mazda Protege

1 Answer

I'm trying to repace the driver's side turn signal - 2002 MPV


if you have ll the screws out then you just need to work it out. there a ball on the lens that pops into a socket on the frame. if it never been removed its a bit of a struggle

Apr 16, 2009 | 2002 Mazda MPV

3 Answers

Cannot get the CV joint Driver side to pry out of the transaxle


take a pry bar between cv and tranny if this is possible and pry out. the c clip on inner shaft is stuck in tranny. common issue.

Apr 15, 2009 | 2002 Mazda 626

1 Answer

Front wheels are not locking in 4wd


the cam assembly in the autolocking hubs is sheared off smooth and needs to b replaced i just did that vary job today

Dec 17, 2008 | 1994 Mazda 2WD B Series Pickup

1 Answer

Drivers side wheel bearing


When you buy the replacement wheel bearing it comes as a sealed unit. This is why they're called hub assemblies.

Jul 03, 2008 | 2000 Mazda 626

1 Answer

MX5 Front Wheel Bearing


Easy fix. Remove the wheel, remove caliper and caliper bracket. Remove brake disc. Pry off hub dust cap. This can be difficult and sometimes the cap cannot be reused. They are inexpensive, however. The hubs are not rebuildable and must be replaced. Undo the large hub nut, remove old unit, replace, reinstall nut, crimp the detent at slot in spindle. (use a punch) Nut torque is #125 ft. pounds to 160. Reinstall cap, caliper bracket, etc.

Jun 09, 2008 | 2002 Mazda Miata

Not finding what you are looking for?
2002 Mazda Protege Logo

1,648 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...