Question about 1984 Chevrolet Camaro

1 Answer

CamaroZ28 Battery voltage was at 12.7 and i can hear the starter clicking but then after i try to turn the key to start my volts go down to about 11.2. Im not sure if my engine is just seized or my starter is shot. Also im not sure if its to hot to start my car and it takes to much voltage to start my car at the temp. it at.

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Clean and check all battery cable connections. If still have problem thn check starter

Posted on Jul 08, 2008

  • bobbynNelda Jul 08, 2008

    through a bad connection you could be losing power



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

You can hear the solenoid engage but the starter doesn't turn. After 5-12 tries it starts.

If you got it recently go and get it exchanged, but most starters only have a 90 day warranty

Feb 11, 2015 | 2004 Dodge Caravan

1 Answer

Why wont my car start it died going down the road replaced starter?

If you put a volt meter on the battery and it reads 12 volts before you cranked the engine and it drops to 10 volts or less when you crank the engine, this indicates you have a bad cell in the battery and you should replace the battery because it is not holding the charge. The loud click sound coming from your starter is because you are not supplying enough voltage to energize it.

Aug 22, 2014 | 1998 Ford Taurus

3 Answers

1995 Isuzu Rodeo won't start all of a sudden.

Check connection battery,could be starter.

Jun 05, 2013 | Cars & Trucks

1 Answer

My 2006 buick lacrosse wont start radio and lights work but its not saying nothing when i try to crank it

Hello! Do you hear a click when the key is turned?...If no click is heard either the ignition key, the Crank relay, the starter, or the battery are suspect...Having lights and radio does not mean the battery is capable of running a starter motor......Put a meter on the battery...should read 12.5 volts...Turn key...Does voltage drop to 8 or 9 volts? Bad battery...If all is well with battery and connections to it...Check the starter fuse # 33 in the under hood fuse/relay box...If the fuse is good that click you should hear is from the Crank Relay in that box...If all of the above is OK connect your meter to the Purple wire that is connected to the starter motor...When the key is turned 12 volts must be on that wire...If there is the starter motor is defective...So, #1...Do you hear a click when key is turned...That would point at a bad starter or weak battery...#2...If you do not hear a click bad fuse #33, bad Crank Relay, bad ignition switch...#3...If fuse is good Bad Crank Relay or Ignition switch; Crank Relay is a low cost item ($10)...Replace Relay...Stop there and send a comment as to results...Guru...saailer

May 06, 2012 | 2006 Buick LaCrosse

1 Answer

My 2008 nissan rogue will not start, i get a clicking sound. The battery is clean, so what could the problem be?

If you have good voltage in the battery and a clicking sound ... either the start solenoid is faulty or the starter is faulty. You can check the start solenoid with a voltage meter. Place the probes one to the starter side of the solenoid the other to ground. Have someone turn the key. The battery side of the solenoid will always have 12 volts on it. The battery side should only have 12 volts when the solenoid is activated (you turned the key). If you get 12 volts on the start side, suspect the starter.

u for your question @

Sep 05, 2011 | 1999 Ford Explorer

1 Answer

My car wont start but my battery is good it just clicks

if your battery has 12 volts and you can hear click noise , try to locate the click noise. If that is coming from the starter location then the starter mtr is not working.a voltage check at the starter mtr with the key in the start position will verify the problem. if 12 volts is not present at the starter mtr thethe start switch or wires could be the problem

Feb 14, 2011 | 2006 Dodge Charger

3 Answers

The booster battery is attached to the dead batttery. Lights go on. When key is turned, hear 1-2 click only.

you may have to let the battery charge from the [boost] 15 minutes should do it. the click you hear is the starter trying to do it;s patient. let car run thats attempting to boost for 15mins while the cables[booster] are attached. trying to start the car any sooner only delays the boost process. you may have to replace your battery in the mercedes to get it running, if it has a dead cell in the old battery.a boost will not always work, but worth the effort. hope this helps and thank you for choosing

Dec 28, 2010 | 2006 Mercedes-Benz B-Class

2 Answers

I Went to start my car at the grocery store today, and when I turned the key all I get is a click from up front.

Sounds like your battery is bad, or the battery cables have built up corrosion so that you need to clean the battery posts and the inside of the cable terminals. When voltage is low, there is enough power to make the starter relay click but not enough to make the starter crank the engine. You are hearing the relay. It is located at the end of the positive cable from the battery.

Jul 25, 2009 | 2000 Ford Taurus

1 Answer

No power to starter

Hi Tonymcder;
Here's what happens in the start sequence when ypi turn the key.

When you turn the key, you should at least hear the starter solenoid click. When you turn the key the ignition switch sends 12 volts to the Starter solenoid ( really just a relay). The Solenoid closes and applies 12 volts (at a high current) to the starter motor to crank the engine. If you have a way to measure voltage, you should get 12 volts at the small terminal on the starter solenoid. The solenoid is mounted on the top of the starter motor.If you get
no voltage, probably an ignition switch If you get 12 volts and the starter doesn't crank the starter is probably defective. At this [point take a small hammer and tap the starter motor, not hard, just medium. Sometimes this will cause the starter motor to catch next time you turn the key. Best bet is to remove the starter motor (with solenoid attached) and take it to an Auto Zone type store where they can check it out for you. Be sure you disconnect the ground terminal of the battery before you attempt to remove the starter motor.
Hope this helps Loringh Thanks for using FixYa

Nov 29, 2008 | BMW 318 Cars & Trucks

2 Answers

My 2002 suburban will not start

First thing I would try is checking the actual battery voltage. Most batteries should be roughly 12.5 if new when sitting at idle. If the lights dim and relays click this is normally a sign of a weak/bad battery connection or possibly a discharged battery. If the battery has good voltage, and the lights continue to dim I would suspect checking the primary wire going to the starter with a 12 volt test light. You will want to check the smaller wire going to the starter and have someone turn the ignition to start. You should have 12 volts there. If you have 12 volts and the starter does nothing I would suspect a faulty starter at this point.

Nov 14, 2008 | 2004 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides